Kodak i600 Series manual Message listing, Id#

Page 59

Message listing

Following is an alphabetic list of messages and corrective actions you can take if one of the following messages is encountered.

Operator Log Message

ID#

Description/Action

 

 

 

Background accessory changed

381

Background Accessory was changed while the scanner was

while powered up

 

powered on.

 

 

• Turn the power off to the scanner, wait a few seconds and

 

 

power the scanner back on.

 

 

• If you get this message and you did not change the

 

 

Background Accessory, clean and calibrate the scanner.

 

 

 

Calibration failed

108

• Try to calibrate the scanner again. Be sure you are using the

 

 

correct calibration target. See Chapter 3, “Calibrating the

 

 

scanner”.

 

 

• Clean the imaging guides. See Chapter 5, Maintenance for

 

 

procedures.

 

 

• If the problem persists, call Service.

 

 

 

Calibration is suggested

185, 585,

• It is suggested that you calibrate the scanner when the current

 

985

batch of documents has completed.

Calibration succeeded

107

Informational message. The scanner has been successfully

 

 

calibrated.

 

 

 

Calibration target is too narrow

331

The calibration target is too small. A 12- x 12-inch calibration

 

 

target is required for Image calibration.

 

 

• Calibrate the scanner again using the correct calibration target.

 

 

 

Call Service

Many ID

A condition was detected that may require repair.

 

numbers

• Turn the power off to the scanner, wait a few seconds and

 

 

power the scanner back on.

 

 

• If the problem persists, call Service.

 

 

 

Check document preparation

123

• Make sure the leading edges of the documents are aligned.

 

 

See Chapter 3, “Document preparation” for more information.

 

 

 

Check imaging guides and lamps

149, 549,

• Verify that the imaging guides are installed correctly. See

 

949

Chapter 5, Maintenance.

 

 

• Clean both sides of the imaging guides.

 

 

• If the pod is closed, and the message persists, call Service.

Close pod and re-enable scanner

306

The pod may have been opened and not closed properly when

 

 

scanning was attempted.

 

 

• Be sure the pod is completely closed.

 

 

 

Document too dark to deskew

143, 543,

Informational message. The scanner was unable to find the

 

943

document edges to determine the skew angle.

 

 

• The document is too dark.

 

 

• The image is too large.

Document too long to rotate

46, 446,

The scanned document was too long to rotate. Scanning was

 

846

stopped.

 

 

• Locate this document and rescan it with a lower resolution or

 

 

with Rotation turned off.

Elevator too full, feed module

297

• There is too much paper in the elevator tray and it is holding

missing or broken

 

the feed module up. The elevator tray capacity is 500 sheets.

 

 

Remove some documents from the elevator tray.

 

 

• The feed module is not installed properly. See Chapter 5,

 

 

Maintenance, for correct installation procedures.

 

 

• If the problem persists, call Service.

 

 

 

6-6

A-61500 April 2007

Page 58 Page 60
Image 59
Page 58 Page 60
Contents Page Contents Appendix a Introduction Scanner models Optional accessories Scanner features Supporting documentation Speed/capacity ThroughputInformation Safety informationUser precautions EnvironmentalAcoustic emission EMC statementsGetting Started Making connections Scanner components Front view Stop/Pause and Start/Resume buttons Internal components Rear view Starting and stopping scanning Using the ScannerTurning the scanner on and off Manually ending scanning Automatically pausing and resuming the scannerMaterials Document preparationAdjusting the side guides and end stop Locking the side guides Adjusting the back of the output trayForward detent positions Exit deflector Adjusting the optional short document tray Automatic feeding Continuous feeding Press Start/Resume Manual feedingSelect Kodak Scanner Calibrating the scannerImage calibration Page Click Calibrate Page Overview Enhanced PrinterFont size Printer specificationsChanging print positions Page Replacing the ink cartridge Page Replacing the blotter strips Page Maintenance Cleaning frequency chart Cleaning tools and materials Ordering parts Supplies and accessoriesOpening the pod Cleaning the output tray and elevator areaCleaning the separation roller tires Cleaning the drive rollersCleaning the feed module tires Close the printer access cover April Cleaning the scanner transport area Cleaning the imaging guides Cleaning the background stripsPage Running a transport cleaning sheet Replacing the feed module or feed module tires Replacement proceduresPage Locking tab Locking tab Slot Replacing the separation roller or separation roller tires Guides Replacing the preSeparation pad Replacing the imagingIndicator lights TroubleshootingScanner is in sleep mode and has detected a hardware error Accessing the Operator Log Page Page ID# Message listingApril Informational message. The pod was closed Informational message. Scanner paused April Listing Numerical messageApril Problem Possible Solution Problem solvingMaintenance Appendix a Accessories Scanner Type/Speed Appendix B Specifications

i600 Series specifications

The Kodak i600 Series is a range of high-performance document scanners designed to meet the needs of businesses requiring reliable and efficient document management solutions. Renowned for its durability and speed, the i600 Series excels in processing large volumes of documents, making it an ideal choice for busy offices and organizations.

One of the standout features of the Kodak i600 Series is its exceptional scanning speed. Equipped to handle up to 130 pages per minute, the scanners significantly reduce the time spent on document processing. This high throughput ensures that even the busiest work environments can maintain productivity without interruption. The automatic document feeder (ADF) can hold up to 500 sheets, allowing for bulk scanning without the need for constant supervision.

The i600 Series utilizes advanced imaging technologies to deliver superior image quality. With its Perfect Page technology, the scanners enhance the clarity and readability of documents irrespective of their original condition. This feature optimizes the scanned images by automatically adjusting brightness, contrast, and color balance. Additionally, the scanners support a range of document types, from large-format pages to mixed-sized documents, ensuring versatility in handling various office materials.

Seamless integration with existing workflows is another hallmark of the Kodak i600 Series. The scanners are compatible with a variety of software applications, enabling users to easily incorporate them into their document management systems. Furthermore, the series supports advanced file formats such as PDF and TIFF, thereby facilitating efficient storage and retrieval processes.

Security is also a top priority for organizations using the i600 Series. The scanners come equipped with features that allow for secure document handling, including user authentication and encryption options. This ensures that sensitive information remains protected throughout the scanning process.

Additionally, the Kodak i600 Series is designed with user-friendliness in mind. The intuitive touchscreen interface simplifies navigation and operation, allowing users to perform tasks with ease. Maintenance is also straightforward, with self-cleaning options that promote longevity and minimize downtime.

In summary, the Kodak i600 Series is a robust and versatile document scanning solution that combines speed, image quality, and security. Its advanced features and user-friendly design make it an excellent choice for businesses looking to enhance their document management capabilities. By streamlining workflows and improving efficiency, the i600 Series helps organizations achieve their goals while effectively managing their critical information.
Top Page Image Contents