Kodak i600 Series manual April

Page 60

Operator Log Message

ID#

Description/Action

Image buffer exceeded threshold

1, 48

The feeder has stopped and the transport is still running

 

 

because the scanner’s internal image buffer is almost full.

 

 

Processing will resume after the host computer has successfully

 

 

retrieved enough images to allow the scanner to continue.

 

 

• Be sure your host computer meets the recommended

 

 

specifications to avoid this condition.

Image outside document area

286

Based on relative cropping parameters, the image to be

 

 

generated from this document would be outside the document

 

 

area.

 

 

• Make sure the relative cropping offset, width and length are

 

 

correct and that the correct document is being scanned.

Image size exceeds available

301

There is not enough room to store this image in the buffer using

memory

 

the current settings.

 

 

• Lower the resolution setting before scanning the next batch of

 

 

documents.

 

 

• Select a different compression value.

Jam in transport

30

A document is lodged in the transport.

 

 

• Remove the documents that have been scanned from the exit

 

 

tray.

 

 

• Open the pod.

 

 

• Remove any jammed documents from inside the transport.

 

 

• Close the pod.

 

 

NOTE: The following procedure is a general guideline. Your

 

 

procedure may be different depending on how your

 

 

application is set up.

 

 

• Verify the last document that was scanned correctly.

 

 

• Place any documents that were not scanned at the top of the

 

 

batch.

 

 

• Place the documents in the elevator tray and begin scanning.

 

 

One or more documents that passed through the transport were

 

 

not scanned.

 

 

• Refeed all documents for which images were not obtained.

 

 

 

Lamps not ready for calibration

110

Calibration was attempted before the lamps were warmed up.

 

 

• Wait until the lamps have completely warmed (90 seconds)

 

 

and try the calibration again.

Lamps not ready for scanning

252

Scanning was attempted before the lamps were warmed up.

 

 

• Try to scan again.

 

 

 

Lamps ready for calibration

278

Informational message. The lamps are warmed and the scanner

 

 

is ready for calibration.

 

 

 

Lamps ready for scanning

280

Informational message. The lamps are warmed and scanning

 

 

can be started.

 

 

 

Lamps timed out

355

• Informational message. The lamps were turned off due to

 

 

inactivity.

Lower imaging guide dirty or

294, 694,

The lower (rear) imaging guide is dirty or there may be a small

document in transport

1094

piece of paper in the imaging guide area.

 

 

• Follow the cleaning procedures in Chapter 5, Maintenance to

 

 

clean the imaging guides.

A-61500 April 2007

6-7

Page 59 Page 61
Image 60
Page 59 Page 61
Contents Page Contents Appendix a Introduction Scanner models Optional accessories Scanner features Speed/capacity Throughput Supporting documentationSafety information User precautionsEnvironmental InformationEMC statements Acoustic emissionGetting Started Making connections Scanner components Front view Stop/Pause and Start/Resume buttons Internal components Rear view Using the Scanner Turning the scanner on and offStarting and stopping scanning Automatically pausing and resuming the scanner Manually ending scanningDocument preparation MaterialsAdjusting the side guides and end stop Adjusting the back of the output tray Locking the side guidesForward detent positions Exit deflector Adjusting the optional short document tray Automatic feeding Continuous feeding Manual feeding Press Start/ResumeCalibrating the scanner Image calibrationSelect Kodak Scanner Page Click Calibrate Page Enhanced Printer OverviewPrinter specifications Font sizeChanging print positions Page Replacing the ink cartridge Page Replacing the blotter strips Page Maintenance Cleaning frequency chart Cleaning tools and materials Supplies and accessories Ordering partsCleaning the output tray and elevator area Opening the podCleaning the drive rollers Cleaning the separation roller tiresCleaning the feed module tires Close the printer access cover April Cleaning the scanner transport area Cleaning the background strips Cleaning the imaging guidesPage Running a transport cleaning sheet Replacement procedures Replacing the feed module or feed module tiresPage Locking tab Locking tab Slot Replacing the separation roller or separation roller tires Replacing the pre Separation padReplacing the imaging GuidesTroubleshooting Indicator lightsScanner is in sleep mode and has detected a hardware error Accessing the Operator Log Page Page Message listing ID#April Informational message. The pod was closed Informational message. Scanner paused April Numerical message ListingApril Problem solving Problem Possible SolutionMaintenance Appendix a Accessories Appendix B Specifications Scanner Type/Speed

i600 Series specifications

The Kodak i600 Series is a range of high-performance document scanners designed to meet the needs of businesses requiring reliable and efficient document management solutions. Renowned for its durability and speed, the i600 Series excels in processing large volumes of documents, making it an ideal choice for busy offices and organizations.

One of the standout features of the Kodak i600 Series is its exceptional scanning speed. Equipped to handle up to 130 pages per minute, the scanners significantly reduce the time spent on document processing. This high throughput ensures that even the busiest work environments can maintain productivity without interruption. The automatic document feeder (ADF) can hold up to 500 sheets, allowing for bulk scanning without the need for constant supervision.

The i600 Series utilizes advanced imaging technologies to deliver superior image quality. With its Perfect Page technology, the scanners enhance the clarity and readability of documents irrespective of their original condition. This feature optimizes the scanned images by automatically adjusting brightness, contrast, and color balance. Additionally, the scanners support a range of document types, from large-format pages to mixed-sized documents, ensuring versatility in handling various office materials.

Seamless integration with existing workflows is another hallmark of the Kodak i600 Series. The scanners are compatible with a variety of software applications, enabling users to easily incorporate them into their document management systems. Furthermore, the series supports advanced file formats such as PDF and TIFF, thereby facilitating efficient storage and retrieval processes.

Security is also a top priority for organizations using the i600 Series. The scanners come equipped with features that allow for secure document handling, including user authentication and encryption options. This ensures that sensitive information remains protected throughout the scanning process.

Additionally, the Kodak i600 Series is designed with user-friendliness in mind. The intuitive touchscreen interface simplifies navigation and operation, allowing users to perform tasks with ease. Maintenance is also straightforward, with self-cleaning options that promote longevity and minimize downtime.

In summary, the Kodak i600 Series is a robust and versatile document scanning solution that combines speed, image quality, and security. Its advanced features and user-friendly design make it an excellent choice for businesses looking to enhance their document management capabilities. By streamlining workflows and improving efficiency, the i600 Series helps organizations achieve their goals while effectively managing their critical information.
Top Page Image Contents