Kodak i1800 Series manual Adjusting the input elevator, Selecting your feeding, position

Page 21

Adjusting the input elevator

Adjusting the input elevator

Adjusting the side guides 1. Place the documents in the input elevator.

2.Adjust the side guides to fit the documents. The side guides should be far enough apart to accommodate the widest document that you are feeding.

Selecting your feeding	The side guides can be adjusted for right-edge, left-edge or center
position	feeding. The side guides can be moved together for center feeding or
	independently for offset feeding (right-edge or left-edge).
	When using the Enhanced Printer, documents should be placed in the
	input elevator in a manner that will align the print string in the proper
	location. Offset feeding may be required.
	If your stack of documents contain mixed sizes and has been left- or
	right-edge aligned, adjust the side guides for offset feeding.
Locking the side guides	Side guides may be locked into position after they are adjusted. This
	may be helpful when the placement of print strings is important.
	If you want to lock the side guides into position, move any documents
	which may be in the input tray and move the locking switch into the
	locked position.

A-61555 March 2007

3-5

Image 21

Contents i1800 Series Scanners User’s GuideA-61555 A-61555March ContentsA-61555March Appendix B Appendix A1 Introduction Scanner features Supporting documentation System requirementsPhone numbers •United States and Canada Contacting Service and SupportUser precautions Safety informationMSDS Gas springs warningEMC statements European UnionEnvironmental information United StatesAcoustic emission Power systemconnection Peoples Republic ofScanner components Front view 2 Getting Started11Exit deflector — aids in document stacking 15 18A-61555March Internal components Rear view Turning the scanner on 3 Using the ScannerA-61555March Starting and stopping scanning Turning the scanner offDocument preparation MaterialsA-61555March Selecting your feeding Adjusting the input elevatorposition Locking the side guidesAdjusting the input tray for document length Adjusting the height of the input elevatorInstalling the document Adjusting the output trayAdjusting the side guides Output tray options1 2 3 Positioning the output trayAdjusting the angle of the output tray Adjusting the end stop3-10 The exit deflector Adjusting the output tray for documents from34 in Adjusting the short document tray 3. Adjust the sides guides as necessary1.Remove the end stop on the output tray Adjusting the height of the scanner Automatic feeding Feeding documents using multi-feeddetectionContinuous feeding Manual feeding Feeding documents that require special handling Using the operator control panel touchscreen Settings screen 3-20 3.Touch Close to return to the Settings screenSelecting the tone Selecting a language addressing for Enabling/disabling imageScanner only cycle the scanner3-24 4.Restart the scannerImage Calibration UDDS Calibration Image Address information Idle screenOperator Log information Accessing scannerCount only mode Performing a Print test Performing a self test Scanning Using function keys when scanning Manually pausing and resuming the scanner Automatically pausing and resuming the scannerResuming from Power Saver mode Power Saver mode Viewing messagesEnhanced Printer overview 4 The Enhanced Printer and Patch ReadersPrinter specifications Changing the front horizontal print position Changing print positionshorizontal print position Changing the rear3.Lift the printer carrier out of position 1.Open the top access cover Replacing the ink cartridge 9.Run a print test Replacing the front blotter strips 9.Replace the ink blotter strip cover 7.Press the blotter strip firmly into the channel10.Close the pod 4-10Replacing the rear blotter strips The Patch Readers Patch function overviewPatch types they are not to specToggle Patch Patch code placement5 Maintenance Cleaning frequency chart Cleaning tools and materials•Kodak Digital Science Roller Cleaning Pads Ordering parts Supplies, consumables and accessories3E9575 9E3357Cleaning procedures Cleaning the OCP touchscreenVacuuming the output tray and input elevator Cleaning the rollers Cleaning the separation roller tires 9. Lift up the printer access cover Cleaning the feed module tires14. Close the printer access cover Vacuuming under the background strips Vacuuming the transport areaguides — basic cleaning Cleaning the imagingUpper imaging guide Cleaning the imaging guides — thorough cleaningLower imaging guide Running a transport cleaning sheetFinal cleaning steps Replacement procedures •Close the pod and the printer access cover 7.Remove one core assembly 15.Close the pod 1.Open the pod separation pad Replacing the preReplacing the imaging guides6 Troubleshooting Accessing the Operator LogAccessing the Operator Log from the touchscreen 4. Select the Scanner icon 2.From the Driver Types box, select TWAIN5. From the main screen, click Settings The Settings screen will be displayed6. Select Device The Device screen will be displayed 8.Select the Logs tabUse the button to create a compressed log package Message listing A-61555March Input elevator too full, feed module A-61555March UDDS calibration failed listing Numerical messageerror condition 6-10phone numbers and detailed information Contacting Service6-12 Problem solvingCalibration has failed Ultralightweight Paper Feed Module Appendix A AccessoriesBackground Accessory Kodak Manual Feeder Resolution Printer AccessoryAppendix B SpecificationsEastman Kodak Company 343 State Street Rochester, NY 14650 U.S.AKodak, 2007. All rights reserved. TM Kodak