Kodak i1800 Series manual Lift the printer carrier out of position

Page 57

3.Lift the printer carrier out of position.

Moving the printer carrier and cable from the front to the rear or vice versa

The scanner comes with the printer carrier and ribbon cable installed for front pre-scan printing. If your application requires rear post-scan printing, the printer carrier and cable must be moved from the front to the rear position. Printing can only be done on the front or the rear.

If you alternate between front and rear printing frequently, you may want to purchase a second printer carrier, then you only need to move the ink cartridge from the front to the back or vice versa. Otherwise, you need to move the printer carrier and cable from the front to rear or rear to front as well as the ink cartridge.

NOTE: After you move the printer carrier and cable you must restart the scanner.

Moving the printer carrier and cable from front position to the rear position

NOTE: Remove the ink cartridge before you begin. See the next section “Replacing the ink cartridge” for procedures.

1.Access the front printer by removing the output tray and lifting the printer access cover.

2.Disconnect the ribbon cable by pulling it straight out from the holder.

3.Lift the printer carrier out of position.

4.Close the printer access cover and reinstall the output tray.

5.Access the rear printer by lifting the top access cover.

6.Install the printer carrier in the desired position.

7.Connect the ribbon cable.

8.Install the ink cartridge. See the next section, “Replacing the ink cartridge” for procedures.

9.Close the top access cover.

10.Restart the scanner.

11.Run a test print.

A-61555 March 2007

4-5

Image 57

Contents i1800 Series Scanners User’s GuideA-61555 A-61555March ContentsA-61555March Appendix B Appendix A1 Introduction Scanner features Supporting documentation System requirementsPhone numbers •United States and Canada Contacting Service and SupportUser precautions Safety informationMSDS Gas springs warningEMC statements European UnionEnvironmental information United StatesAcoustic emission Power systemconnection Peoples Republic ofScanner components Front view 2 Getting Started11Exit deflector — aids in document stacking 15 18A-61555March Internal components Rear view Turning the scanner on 3 Using the ScannerA-61555March Starting and stopping scanning Turning the scanner offDocument preparation MaterialsA-61555March Selecting your feeding Adjusting the input elevatorposition Locking the side guidesAdjusting the input tray for document length Adjusting the height of the input elevatorInstalling the document Adjusting the output trayAdjusting the side guides Output tray options1 2 3 Positioning the output trayAdjusting the angle of the output tray Adjusting the end stop3-10 The exit deflector Adjusting the output tray for documents from34 in Adjusting the short document tray 3. Adjust the sides guides as necessary1.Remove the end stop on the output tray Adjusting the height of the scanner Automatic feeding Feeding documents using multi-feeddetectionContinuous feeding Manual feeding Feeding documents that require special handling Using the operator control panel touchscreen Settings screen 3-20 3.Touch Close to return to the Settings screenSelecting the tone Selecting a language addressing for Enabling/disabling imageScanner only cycle the scanner3-24 4.Restart the scannerImage Calibration UDDS Calibration Image Address information Idle screenOperator Log information Accessing scannerCount only mode Performing a Print test Performing a self test Scanning Using function keys when scanning Manually pausing and resuming the scanner Automatically pausing and resuming the scannerResuming from Power Saver mode Power Saver mode Viewing messagesEnhanced Printer overview 4 The Enhanced Printer and Patch ReadersPrinter specifications Changing the front horizontal print position Changing print positionshorizontal print position Changing the rear3.Lift the printer carrier out of position 1.Open the top access cover Replacing the ink cartridge 9.Run a print test Replacing the front blotter strips 9.Replace the ink blotter strip cover 7.Press the blotter strip firmly into the channel10.Close the pod 4-10Replacing the rear blotter strips The Patch Readers Patch function overviewPatch types they are not to specToggle Patch Patch code placement5 Maintenance Cleaning frequency chart Cleaning tools and materials•Kodak Digital Science Roller Cleaning Pads Ordering parts Supplies, consumables and accessories3E9575 9E3357Cleaning procedures Cleaning the OCP touchscreenVacuuming the output tray and input elevator Cleaning the rollers Cleaning the separation roller tires 9. Lift up the printer access cover Cleaning the feed module tires14. Close the printer access cover Vacuuming under the background strips Vacuuming the transport areaguides — basic cleaning Cleaning the imagingUpper imaging guide Cleaning the imaging guides — thorough cleaningLower imaging guide Running a transport cleaning sheetFinal cleaning steps Replacement procedures •Close the pod and the printer access cover 7.Remove one core assembly 15.Close the pod 1.Open the pod separation pad Replacing the preReplacing the imaging guides6 Troubleshooting Accessing the Operator LogAccessing the Operator Log from the touchscreen 4. Select the Scanner icon 2.From the Driver Types box, select TWAIN5. From the main screen, click Settings The Settings screen will be displayed6. Select Device The Device screen will be displayed 8.Select the Logs tabUse the button to create a compressed log package Message listing A-61555March Input elevator too full, feed module A-61555March UDDS calibration failed listing Numerical messageerror condition 6-10phone numbers and detailed information Contacting Service6-12 Problem solvingCalibration has failed Ultralightweight Paper Feed Module Appendix A AccessoriesBackground Accessory Kodak Manual Feeder Resolution Printer AccessoryAppendix B SpecificationsEastman Kodak Company 343 State Street Rochester, NY 14650 U.S.AKodak, 2007. All rights reserved. TM Kodak