Kodak i1800 Series manual Replacing the rear blotter strips

Page 63

Replacing the rear blotter strips

Replacing the rear blotter strips

Blotter strips collect ink overflow. They should be replaced when there is a build-up of ink. Replacement blotter strips may be purchased through your supplier.

1.Remove the output tray. The rear blotter strips are located in the two drawers underneath the baffle.

2.Open the one of the drawers by pushing it in a little and lifting up slightly, then pull it out.

3.Peel off the soiled blotter strip.

4.Peel the backing away from the new blotter strip.

5.Align the blotter strip in the channel. Be sure it is properly aligned before pressing the adhesive side into the channel.

6.Press the blotter strip firmly into place.

7.Repeat Steps 2 - 5 for the other blotter strip.

8.Close the drawer(s) by pushing it in and sliding it down slightly. This will lock the drawer in place.

9.Replace the output tray.

A-61555 March 2007

4-11

Image 63

Contents i1800 Series Scanners User’s GuideA-61555 A-61555March ContentsA-61555March Appendix B Appendix A1 Introduction Scanner features Supporting documentation System requirementsPhone numbers •United States and Canada Contacting Service and SupportGas springs warning Safety informationUser precautions MSDSUnited States European UnionEMC statements Environmental informationPeoples Republic of Power systemAcoustic emission connectionScanner components Front view 2 Getting Started11Exit deflector — aids in document stacking 15 18A-61555March Internal components Rear view Turning the scanner on 3 Using the ScannerA-61555March Materials Turning the scanner offStarting and stopping scanning Document preparationA-61555March Locking the side guides Adjusting the input elevatorSelecting your feeding positionAdjusting the input tray for document length Adjusting the height of the input elevatorOutput tray options Adjusting the output trayInstalling the document Adjusting the side guides1 2 3 Positioning the output trayAdjusting the angle of the output tray Adjusting the end stop3-10 The exit deflector Adjusting the output tray for documents from34 in Adjusting the short document tray 3. Adjust the sides guides as necessary1.Remove the end stop on the output tray Adjusting the height of the scanner Automatic feeding Feeding documents using multi-feeddetectionContinuous feeding Manual feeding Feeding documents that require special handling Using the operator control panel touchscreen Settings screen 3-20 3.Touch Close to return to the Settings screenSelecting the tone Selecting a language cycle the scanner Enabling/disabling imageaddressing for Scanner only3-24 4.Restart the scannerImage Calibration UDDS Calibration Image Address information Idle screenOperator Log information Accessing scannerCount only mode Performing a Print test Performing a self test Scanning Using function keys when scanning Manually pausing and resuming the scanner Automatically pausing and resuming the scannerResuming from Power Saver mode Power Saver mode Viewing messagesEnhanced Printer overview 4 The Enhanced Printer and Patch ReadersPrinter specifications Changing the front horizontal print position Changing print positionshorizontal print position Changing the rear3.Lift the printer carrier out of position 1.Open the top access cover Replacing the ink cartridge 9.Run a print test Replacing the front blotter strips 4-10 7.Press the blotter strip firmly into the channel9.Replace the ink blotter strip cover 10.Close the podReplacing the rear blotter strips they are not to spec Patch function overviewThe Patch Readers Patch typesToggle Patch Patch code placement5 Maintenance Cleaning frequency chart Cleaning tools and materials•Kodak Digital Science Roller Cleaning Pads 9E3357 Supplies, consumables and accessoriesOrdering parts 3E9575Cleaning procedures Cleaning the OCP touchscreenVacuuming the output tray and input elevator Cleaning the rollers Cleaning the separation roller tires 9. Lift up the printer access cover Cleaning the feed module tires14. Close the printer access cover Vacuuming under the background strips Vacuuming the transport areaguides — basic cleaning Cleaning the imagingUpper imaging guide Cleaning the imaging guides — thorough cleaningLower imaging guide Running a transport cleaning sheetFinal cleaning steps Replacement procedures •Close the pod and the printer access cover 7.Remove one core assembly 15.Close the pod 1.Open the pod guides Replacing the preseparation pad Replacing the imaging6 Troubleshooting Accessing the Operator LogAccessing the Operator Log from the touchscreen 4. Select the Scanner icon 2.From the Driver Types box, select TWAIN5. From the main screen, click Settings The Settings screen will be displayed6. Select Device The Device screen will be displayed 8.Select the Logs tabUse the button to create a compressed log package Message listing A-61555March Input elevator too full, feed module A-61555March UDDS calibration failed 6-10 Numerical messagelisting error conditionphone numbers and detailed information Contacting Service6-12 Problem solvingCalibration has failed Resolution Printer Accessory Appendix A AccessoriesUltralightweight Paper Feed Module Background Accessory Kodak Manual FeederAppendix B SpecificationsEastman Kodak Company 343 State Street Rochester, NY 14650 U.S.AKodak, 2007. All rights reserved. TM Kodak