Kodak i1800 Series manual Automatic feeding, Feeding documents using multi-feeddetection

Page 31

Feeding documents using multi-feed detection

Feeding documents using multi-feed detection

Automatic feeding

The scanner has three multi-feed detection sensors that can be independently enabled or disabled. When multi-feed detection is enabled, adjust the side guides so the documents fully cover at least one sensor. If the document partially covers a sensor, false multi-feeds may occur.

To scan a stack of documents follow the guidelines for size, type, quantity, etc., outlined in the “Document preparation” section.

For faster throughput, place documents into the input elevator in landscape orientation (longer side as the leading edge).

IMPORTANT: Staples and paper clips on documents may damage the scanner. Remove all staples and paper clips before scanning.

1.Align the leading edges of the stacked documents.

2.Position the stack of the documents, face up in the input elevator so the stack covers the paper present sensor.

Depending on how your capture application software is configured, your documents will automatically start feeding, or you may need to touch the Scan button on the touchscreen to begin feeding documents.

A-61555 March 2007

3-15

Image 31

Contents User’s Guide i1800 Series ScannersA-61555 A-61555March ContentsA-61555March Appendix B Appendix A1 Introduction Scanner features Supporting documentation System requirementsPhone numbers •United States and Canada Contacting Service and SupportGas springs warning Safety informationUser precautions MSDSUnited States European UnionEMC statements Environmental informationPeoples Republic of Power systemAcoustic emission connectionScanner components Front view 2 Getting Started11Exit deflector — aids in document stacking 15 18A-61555March Internal components Rear view Turning the scanner on 3 Using the ScannerA-61555March Materials Turning the scanner offStarting and stopping scanning Document preparationA-61555March Locking the side guides Adjusting the input elevatorSelecting your feeding positionAdjusting the input tray for document length Adjusting the height of the input elevatorOutput tray options Adjusting the output trayInstalling the document Adjusting the side guides1 2 3 Positioning the output trayAdjusting the angle of the output tray Adjusting the end stop3-10 The exit deflector for documents from Adjusting the output tray34 in 3. Adjust the sides guides as necessary Adjusting the short document tray1.Remove the end stop on the output tray Adjusting the height of the scanner Automatic feeding Feeding documents using multi-feeddetectionContinuous feeding Manual feeding Feeding documents that require special handling Using the operator control panel touchscreen Settings screen 3-20 3.Touch Close to return to the Settings screenSelecting the tone Selecting a language cycle the scanner Enabling/disabling imageaddressing for Scanner only3-24 4.Restart the scannerImage Calibration UDDS Calibration Image Address information Idle screenOperator Log information Accessing scannerCount only mode Performing a Print test Performing a self test Scanning Using function keys when scanning Manually pausing and resuming the scanner Automatically pausing and resuming the scannerResuming from Power Saver mode Power Saver mode Viewing messagesEnhanced Printer overview 4 The Enhanced Printer and Patch ReadersPrinter specifications Changing the front horizontal print position Changing print positionshorizontal print position Changing the rear3.Lift the printer carrier out of position 1.Open the top access cover Replacing the ink cartridge 9.Run a print test Replacing the front blotter strips 4-10 7.Press the blotter strip firmly into the channel9.Replace the ink blotter strip cover 10.Close the podReplacing the rear blotter strips they are not to spec Patch function overviewThe Patch Readers Patch typesToggle Patch Patch code placement5 Maintenance Cleaning tools and materials Cleaning frequency chart•Kodak Digital Science Roller Cleaning Pads 9E3357 Supplies, consumables and accessoriesOrdering parts 3E9575Cleaning the OCP touchscreen Cleaning proceduresVacuuming the output tray and input elevator Cleaning the rollers Cleaning the separation roller tires 9. Lift up the printer access cover Cleaning the feed module tires14. Close the printer access cover Vacuuming under the background strips Vacuuming the transport areaguides — basic cleaning Cleaning the imagingUpper imaging guide Cleaning the imaging guides — thorough cleaningLower imaging guide Running a transport cleaning sheetFinal cleaning steps Replacement procedures •Close the pod and the printer access cover 7.Remove one core assembly 15.Close the pod 1.Open the pod guides Replacing the preseparation pad Replacing the imagingAccessing the Operator Log 6 TroubleshootingAccessing the Operator Log from the touchscreen 4. Select the Scanner icon 2.From the Driver Types box, select TWAINThe Settings screen will be displayed 5. From the main screen, click Settings6. Select Device 8.Select the Logs tab The Device screen will be displayedUse the button to create a compressed log package Message listing A-61555March Input elevator too full, feed module A-61555March UDDS calibration failed 6-10 Numerical messagelisting error conditionphone numbers and detailed information Contacting Service6-12 Problem solvingCalibration has failed Resolution Printer Accessory Appendix A AccessoriesUltralightweight Paper Feed Module Background Accessory Kodak Manual FeederAppendix B SpecificationsRochester, NY 14650 U.S.A Eastman Kodak Company 343 State StreetKodak, 2007. All rights reserved. TM Kodak