Kodak i1800 Series manual Lower imaging guide

Page 77

Lower imaging guide

Lower imaging guide

1.Turn the screw on each end of the lower imaging guide, remove it from its position and set it aside.

2.Carefully vacuum the areas between the lamps, then use a Staticide wipe to thoroughly clean the glass plate between the lamps.

3.Clean the lower imaging guide thoroughly with a Staticide wipe.

4.Wipe the imaging guide again with an almost-dry Staticide wipe to remove any streaks.

5.Reinstall the lower imaging guide.

6.Close the pod.

5-12	A-61555 March 2007

Image 77

Contents A-61555 i1800 Series ScannersUser’s Guide A-61555March ContentsA-61555March Appendix B Appendix A1 Introduction Scanner features Supporting documentation System requirementsPhone numbers •United States and Canada Contacting Service and SupportUser precautions Safety informationMSDS Gas springs warningEMC statements European UnionEnvironmental information United StatesAcoustic emission Power systemconnection Peoples Republic ofScanner components Front view 2 Getting Started11Exit deflector — aids in document stacking 15 18A-61555March Internal components Rear view Turning the scanner on 3 Using the ScannerA-61555March Starting and stopping scanning Turning the scanner offDocument preparation MaterialsA-61555March Selecting your feeding Adjusting the input elevatorposition Locking the side guidesAdjusting the input tray for document length Adjusting the height of the input elevatorInstalling the document Adjusting the output trayAdjusting the side guides Output tray options1 2 3 Positioning the output trayAdjusting the angle of the output tray Adjusting the end stop3-10 The exit deflector 34 in Adjusting the output trayfor documents from 1.Remove the end stop on the output tray Adjusting the short document tray3. Adjust the sides guides as necessary Adjusting the height of the scanner Automatic feeding Feeding documents using multi-feeddetectionContinuous feeding Manual feeding Feeding documents that require special handling Using the operator control panel touchscreen Settings screen 3-20 3.Touch Close to return to the Settings screenSelecting the tone Selecting a language addressing for Enabling/disabling imageScanner only cycle the scanner3-24 4.Restart the scannerImage Calibration UDDS Calibration Image Address information Idle screenOperator Log information Accessing scannerCount only mode Performing a Print test Performing a self test Scanning Using function keys when scanning Manually pausing and resuming the scanner Automatically pausing and resuming the scannerResuming from Power Saver mode Power Saver mode Viewing messagesEnhanced Printer overview 4 The Enhanced Printer and Patch ReadersPrinter specifications Changing the front horizontal print position Changing print positionshorizontal print position Changing the rear3.Lift the printer carrier out of position 1.Open the top access cover Replacing the ink cartridge 9.Run a print test Replacing the front blotter strips 9.Replace the ink blotter strip cover 7.Press the blotter strip firmly into the channel10.Close the pod 4-10Replacing the rear blotter strips The Patch Readers Patch function overviewPatch types they are not to specToggle Patch Patch code placement5 Maintenance •Kodak Digital Science Roller Cleaning Pads Cleaning frequency chartCleaning tools and materials Ordering parts Supplies, consumables and accessories3E9575 9E3357Vacuuming the output tray and input elevator Cleaning proceduresCleaning the OCP touchscreen Cleaning the rollers Cleaning the separation roller tires 9. Lift up the printer access cover Cleaning the feed module tires14. Close the printer access cover Vacuuming under the background strips Vacuuming the transport areaguides — basic cleaning Cleaning the imagingUpper imaging guide Cleaning the imaging guides — thorough cleaningLower imaging guide Running a transport cleaning sheetFinal cleaning steps Replacement procedures •Close the pod and the printer access cover 7.Remove one core assembly 15.Close the pod 1.Open the pod separation pad Replacing the preReplacing the imaging guidesAccessing the Operator Log from the touchscreen 6 TroubleshootingAccessing the Operator Log 4. Select the Scanner icon 2.From the Driver Types box, select TWAIN6. Select Device 5. From the main screen, click SettingsThe Settings screen will be displayed Use the button to create a compressed log package The Device screen will be displayed8.Select the Logs tab Message listing A-61555March Input elevator too full, feed module A-61555March UDDS calibration failed listing Numerical messageerror condition 6-10phone numbers and detailed information Contacting Service6-12 Problem solvingCalibration has failed Ultralightweight Paper Feed Module Appendix A AccessoriesBackground Accessory Kodak Manual Feeder Resolution Printer AccessoryAppendix B SpecificationsKodak, 2007. All rights reserved. TM Kodak Eastman Kodak Company 343 State StreetRochester, NY 14650 U.S.A