Kodak i1800 Series manual A-61555March

Page 93
Manual background

Messages

ID#

Operator Message

Paused waiting for host

1, 48

The feeder has stopped and the transport is still running

 

 

because the scanner’s internal image buffer is almost full.

 

 

Processing will automatically resume after the capture software

 

 

application has successfully retrieved enough images to allow

 

 

the scanner to continue.

 

 

• Be sure your host computer meets the recommended

 

 

specifications to avoid this condition.

Please update firmware before

91

The expected production version of operational firmware was

scanning

 

not found. The back-up firmware is in use.

 

 

• Reload the most recent version of operational scanner

 

 

firmware.

Pod door closed

26

Informational message. The pod was closed.

 

 

 

Pod door opened

25

Informational message. The pod is not closed completely.

 

 

 

Power on self-test completed

20

Informational message. The scanner has completed its self-tests

 

 

after power-on.

Power on self-test failed

6

This error could occur during scanner power-up.

 

 

• Power-down the scanner, then power down the PC. Wait a few

 

 

seconds and then power the PC back up, then power up the

 

 

scanner.

 

 

• If the problem persists, call Service.

Printer bitmap font in use

281

Informational message. An alternate printer font file was found

 

 

and is being used instead of the default font.

 

 

 

Rear calibration failed

112

The rear imaging path calibration failed.

 

 

• Clean the imaging guides. See Chapter 5, Maintenance for

 

 

procedures.

 

 

• Try to calibrate the scanner again. Be sure you are using the

 

 

correct calibration target. See Chapter 3, “Calibrating the

 

 

Scanner”.

 

 

• If the problem persists, call Service.

 

 

 

Rear calibration succeeded

113

Informational message. The rear image path has been

 

 

successfully calibrated.

 

 

 

Refeed document set

Many ID

Documents passed through the transport but no images were

 

numbers

created.

 

 

• Clean document sensors.

 

 

• Make sure the leading edges of the documents are aligned.

 

 

See Chapter 3, “Document preparation” for more information.

 

 

• Check the condition of your feed module and separation roller

 

 

tires and your pre-separation pad. Clean and replace if

 

 

necessary.

 

 

• Refeed these documents and verify that the images have been

 

 

captured.

 

 

 

Requested pages scanned

337

Informational message. The scanner has completed scanning

 

 

the requested number of documents.

Paused for image processing

63

Informational message. Scanner paused.

 

 

• Slow host PC may not be able to keep up with the scanner.

 

 

 

Transport timeout

336

Informational message. The transport was turned off due to

 

 

inactivity.

 

 

 

6-8

A-61555 March 2007

Page 92 Page 94
Image 93
Page 92 Page 94
Contents i1800 Series Scanners User’s GuideA-61555 A-61555March ContentsA-61555March Appendix B Appendix A1 Introduction Scanner features Supporting documentation System requirementsPhone numbers •United States and Canada Contacting Service and SupportUser precautions Safety informationMSDS Gas springs warningEMC statements European UnionEnvironmental information United StatesAcoustic emission Power systemconnection Peoples Republic ofScanner components Front view 2 Getting Started11Exit deflector — aids in document stacking 15 18A-61555March Internal components Rear view Turning the scanner on 3 Using the ScannerA-61555March Starting and stopping scanning Turning the scanner offDocument preparation MaterialsA-61555March Selecting your feeding Adjusting the input elevatorposition Locking the side guidesAdjusting the input tray for document length Adjusting the height of the input elevatorInstalling the document Adjusting the output trayAdjusting the side guides Output tray options1 2 3 Positioning the output trayAdjusting the angle of the output tray Adjusting the end stop3-10 The exit deflector Adjusting the output tray for documents from34 in Adjusting the short document tray 3. Adjust the sides guides as necessary1.Remove the end stop on the output tray Adjusting the height of the scanner Automatic feeding Feeding documents using multi-feeddetectionContinuous feeding Manual feeding Feeding documents that require special handling Using the operator control panel touchscreen Settings screen 3-20 3.Touch Close to return to the Settings screenSelecting the tone Selecting a language addressing for Enabling/disabling imageScanner only cycle the scanner3-24 4.Restart the scannerImage Calibration UDDS Calibration Image Address information Idle screenOperator Log information Accessing scannerCount only mode Performing a Print test Performing a self test Scanning Using function keys when scanning Manually pausing and resuming the scanner Automatically pausing and resuming the scannerResuming from Power Saver mode Power Saver mode Viewing messagesEnhanced Printer overview 4 The Enhanced Printer and Patch ReadersPrinter specifications Changing the front horizontal print position Changing print positionshorizontal print position Changing the rear3.Lift the printer carrier out of position 1.Open the top access cover Replacing the ink cartridge 9.Run a print test Replacing the front blotter strips 9.Replace the ink blotter strip cover 7.Press the blotter strip firmly into the channel10.Close the pod 4-10Replacing the rear blotter strips The Patch Readers Patch function overviewPatch types they are not to specToggle Patch Patch code placement5 Maintenance Cleaning frequency chart Cleaning tools and materials•Kodak Digital Science Roller Cleaning Pads Ordering parts Supplies, consumables and accessories3E9575 9E3357Cleaning procedures Cleaning the OCP touchscreenVacuuming the output tray and input elevator Cleaning the rollers Cleaning the separation roller tires 9. Lift up the printer access cover Cleaning the feed module tires14. Close the printer access cover Vacuuming under the background strips Vacuuming the transport areaguides — basic cleaning Cleaning the imagingUpper imaging guide Cleaning the imaging guides — thorough cleaningLower imaging guide Running a transport cleaning sheetFinal cleaning steps Replacement procedures •Close the pod and the printer access cover 7.Remove one core assembly 15.Close the pod 1.Open the pod separation pad Replacing the preReplacing the imaging guides6 Troubleshooting Accessing the Operator LogAccessing the Operator Log from the touchscreen 4. Select the Scanner icon 2.From the Driver Types box, select TWAIN5. From the main screen, click Settings The Settings screen will be displayed6. Select Device The Device screen will be displayed 8.Select the Logs tabUse the button to create a compressed log package Message listing A-61555March Input elevator too full, feed module A-61555March UDDS calibration failed listing Numerical messageerror condition 6-10phone numbers and detailed information Contacting Service6-12 Problem solvingCalibration has failed Ultralightweight Paper Feed Module Appendix A AccessoriesBackground Accessory Kodak Manual Feeder Resolution Printer AccessoryAppendix B SpecificationsEastman Kodak Company 343 State Street Rochester, NY 14650 U.S.AKodak, 2007. All rights reserved. TM Kodak
Top Page Image Contents