Kodak i1800 Series manual Replacing the front blotter strips

Page 61

Replacing the front blotter strips

Replacing the front blotter strips

Blotter strips collect ink overflow. They should be replaced when there is a build-up of ink. Replacement blotter strips may be purchased through your supplier.

1.Open the pod.

2.Use the green tab to lift and remove the ink blotter strip cover to access the front blotter strips.

Remove Ink Blotter Strip cover

3.Carefully pull the blotter strip(s) off the transport. You can replace one or both of the strips as necessary..

4.Discard the soiled strip(s)

5.Peel the backing away from the blotter strip.

A-61555 March 2007

4-9

Image 61

Contents User’s Guide i1800 Series ScannersA-61555 A-61555March ContentsA-61555March Appendix B Appendix A1 Introduction Scanner features Supporting documentation System requirementsPhone numbers •United States and Canada Contacting Service and SupportUser precautions Safety informationMSDS Gas springs warningEMC statements European UnionEnvironmental information United StatesAcoustic emission Power systemconnection Peoples Republic ofScanner components Front view 2 Getting Started11Exit deflector — aids in document stacking 15 18A-61555March Internal components Rear view Turning the scanner on 3 Using the ScannerA-61555March Starting and stopping scanning Turning the scanner offDocument preparation MaterialsA-61555March Selecting your feeding Adjusting the input elevatorposition Locking the side guidesAdjusting the input tray for document length Adjusting the height of the input elevatorInstalling the document Adjusting the output trayAdjusting the side guides Output tray options1 2 3 Positioning the output trayAdjusting the angle of the output tray Adjusting the end stop3-10 The exit deflector for documents from Adjusting the output tray34 in 3. Adjust the sides guides as necessary Adjusting the short document tray1.Remove the end stop on the output tray Adjusting the height of the scanner Automatic feeding Feeding documents using multi-feeddetectionContinuous feeding Manual feeding Feeding documents that require special handling Using the operator control panel touchscreen Settings screen 3-20 3.Touch Close to return to the Settings screenSelecting the tone Selecting a language addressing for Enabling/disabling imageScanner only cycle the scanner3-24 4.Restart the scannerImage Calibration UDDS Calibration Image Address information Idle screenOperator Log information Accessing scannerCount only mode Performing a Print test Performing a self test Scanning Using function keys when scanning Manually pausing and resuming the scanner Automatically pausing and resuming the scannerResuming from Power Saver mode Power Saver mode Viewing messagesEnhanced Printer overview 4 The Enhanced Printer and Patch ReadersPrinter specifications Changing the front horizontal print position Changing print positionshorizontal print position Changing the rear3.Lift the printer carrier out of position 1.Open the top access cover Replacing the ink cartridge 9.Run a print test Replacing the front blotter strips 9.Replace the ink blotter strip cover 7.Press the blotter strip firmly into the channel10.Close the pod 4-10Replacing the rear blotter strips The Patch Readers Patch function overviewPatch types they are not to specToggle Patch Patch code placement5 Maintenance Cleaning tools and materials Cleaning frequency chart•Kodak Digital Science Roller Cleaning Pads Ordering parts Supplies, consumables and accessories3E9575 9E3357Cleaning the OCP touchscreen Cleaning proceduresVacuuming the output tray and input elevator Cleaning the rollers Cleaning the separation roller tires 9. Lift up the printer access cover Cleaning the feed module tires14. Close the printer access cover Vacuuming under the background strips Vacuuming the transport areaguides — basic cleaning Cleaning the imagingUpper imaging guide Cleaning the imaging guides — thorough cleaningLower imaging guide Running a transport cleaning sheetFinal cleaning steps Replacement procedures •Close the pod and the printer access cover 7.Remove one core assembly 15.Close the pod 1.Open the pod separation pad Replacing the preReplacing the imaging guidesAccessing the Operator Log 6 TroubleshootingAccessing the Operator Log from the touchscreen 4. Select the Scanner icon 2.From the Driver Types box, select TWAINThe Settings screen will be displayed 5. From the main screen, click Settings6. Select Device 8.Select the Logs tab The Device screen will be displayedUse the button to create a compressed log package Message listing A-61555March Input elevator too full, feed module A-61555March UDDS calibration failed listing Numerical messageerror condition 6-10phone numbers and detailed information Contacting Service6-12 Problem solvingCalibration has failed Ultralightweight Paper Feed Module Appendix A AccessoriesBackground Accessory Kodak Manual Feeder Resolution Printer AccessoryAppendix B SpecificationsRochester, NY 14650 U.S.A Eastman Kodak Company 343 State StreetKodak, 2007. All rights reserved. TM Kodak