Kodak A-61167 manual Replacing parts, Cleaning the paper path, CAT No

Page 32

Cleaning the paper path

1.

Remove the wrapping from the Transport Cleaning Sheet.

 

 

2.

Adjust the paper feeder guides to fit the cleaning sheet.

 

 

3.

Feed the cleaning sheet (adhesive side up) through the scanner in portrait

 

 

orientation until all residue is removed from the drive rollers.

 

 

4.

Adjust the feeder guides to fit, then feed the cleaning sheet (adhesive side

 

 

up) through the scanner in landscape orientation until all residue is

 

 

removed from the drive rollers.

 

 

5.

Using the same cleaning sheet, repeat Steps 3 and 4, but feed the

 

 

cleaning sheet through the scanner with the adhesive side down until all

 

 

residue is removed from the drive rollers.

 

 

NOTE: When a cleaning sheet gets very dirty, discard it and use a new one.

Replacing parts

Customer-replacement parts (feed module, separator module, pre-separation

 

pad, roller tires, and installation instructions) are available in the following kits:

 

 

 

 

 

 

 

Item

 

CAT No.

 

 

 

 

 

Kodak Feeder Consumables Kit for i200 Series Scanners (1

 

124 1066

 

complete feed module, 1 complete separator module, 2 pre-

 

 

 

separation pads, 24 tires)

 

 

 

 

 

 

 

Kodak Extra-Large Feeder Consumables Kit for i200 Series

 

821 5808

 

Scanners (5 complete feed modules, 5 complete separator

 

 

 

modules, 10 pre-separation pads, 120 tires)

 

 

 

 

 

 

 

Kodak Imaging Guide Set (1 upper, 1 lower)

 

120 0278

 

 

 

 

 

Use only these replacement parts in your scanner.

 

The expected life of customer-replaceable parts is shown below.

Kodak Separator Module for i200 Series Scanners: 200,000 document pages

Kodak Feed Module for i200 Series Scanners: 500,000 document pages

NOTES: The composition of the tire materials was engineered to provide the ultimate in feeding reliability across the broadest range of document types, sizes, and thicknesses. Expected life figures are offered as guidelines for operations that follow the recommended scanner cleaning procedures in this section and that scan document types within the recommended paper types (refer to “Preparing documents for scanning” in the Introduction section).

Your experience may vary. Certain paper types (such as carbonless paper or newsprint), failure to clean regularly, and/or use of non- recommended cleaning solvents can shorten tire life.

Tire life may be reduced due to a long transport timeout setting.

To order replacement parts, refer to Appendix B, Supplies and Accessories.

28

A-61167 April 2005

Image 32
Contents User’s Guide Contents Using the Scanner TroubleshootingAppendix D Kodak i200 Series Dockable Flatbed Scanner features IntroductionPaper transport features Image quality featuresMaintenance Speed/Capacity ThroughputOptional accessories Preparing documents for scanning Recommended documents Safety information User precautionsSafety and regulatory agency approvals Environmental information Acoustic emission Power system EMC statements United StatesJapan TaiwanInstalling the Scanner Site specificationsSystem requirements Front Unpacking the scanner Registering your scannerScanner components Internal RearSide Making connections Power setup Page Page Tray extenders and side guides Page Continuous feeding Using the ScannerStarting and stopping scanning Automatic feeding Manual feeding Damaged documentsSpecial Document mode Additional featuresLong Paper mode Toggle patch Perfect Page withIThresholding Maintenance Cleaning the scannerCleaning the separator module Front roller cover Page Cleaning the imaging guides CAT No Replacing partsCleaning the paper path Click Calibrate Lamps Clearing document jams TroubleshootingIndicator lights Adjusting the separator module tension System is not responding Color image quality Problem solving Problem Possible SolutionProblem Possible Solution Transporting the scanner Appendix a Specifications Power Source Scanner DimensionsScanner Weight DimensionsAppendix B Supplies and Accessories Contents of the imprinter kit Appendix C Kodak i200 Series ImprinterInstalling the imprinter Removing the circuit board coverAttaching the imprinter board and cable Thumbscrews Hook Imprinter connector Page Page Completing the imprinter installation Page Installing the ink blotter strips Installing an ink cartridge Setting the imprinter position Imprinter maintenance Replacing the ink blotter strips Replacing Ink cartridge carrier Print characters Printable Character SetImprinter specifications Appendix D Kodak i200 Series Dockable Flatbed Contents of the dockable flatbed kit Flatbed specificationsInstalling the dockable flatbed Remove the scanner front panel Using the flatbed Book scanningClick Calibrate Cleaning the flatbed After a power failure Removing the dockable flatbed Press firmly against the right side of the door to latch it Scanner Model Document Size Basic Memory Total Memory Appendix E Installing Optional MemoryInstalling memory in the scanner Circuit board cover Remove the existing memory card from the main control board Eastman Kodak Company