Emerson 48330 user manual Querying System Status, First Page Of System Information

Page 46

36	Chapter 5 Operating SCU

4.At any system information page, press “ENT” to enter the “MAIN MENU” page, which contains 3 sub-menus: “Status”, “Maintenance” and “Settings”.

Main Menu

Status

Maintenance

Settings

You can press “ ” or “ ” repeatedly to select a sub-menu, and press “ENT” to enter the sub-menu. Press “ESC” to return to the menu of higher level.

1) Status

Including rectifier information, active alarm information and alarm history information.

2) Maintenance

The maintenance operation can be conducted only when the battery management mode is set to “Manual”. The maintenance includes battery FC, BC and test, load power off/on, battery power off/on and rectifier voltage trimming, current limit, switch control and resetting.

3) Settings

Including the setting of alarm parameter, battery parameter, AC/DC parameter, rectifier parameter and system parameter.

5.3Querying System Status

5.3.1First Page Of System Information

1.At the main menu page, press “ESC” to return to the first system information page.

2.If no operation is conducted on the monitoring module keypad for 8 minutes, the LCD will return to the first system information page and shut down the backlight to protect the screen. Pressing any key will turn on the back light.

The first system information page contains the major system operation information, including date/time, busbar voltage, total load current, system operation state (normal or alarm), battery management mode (AUTO or MANUAL) and battery state.

Among which, the battery state include FC, temperature compensation, BC, Cyclic Boost, test, short test and scheduled test. The current time are displayed in two pages shifting at the interval of 2s. One page shows year, month and date, the

ACTURA Flex 48330 Power System User Manual

Image 46

Contents Version V1.0 Revision date May 20 31011084Safety Precautions Electrical SafetyBattery Special Safe Requirements of This Equipment OthersContents System Settings Alarm Settings TestingTemperature Compensation Coefficient Parameters Routine MaintenanceDaily Inspection Replacement Appendix15 Value description of AC settings Changing audible/visual alarm and alarm call back planFunctions of SCU keys Figure List Page Abbreviation FeaturesSystem Description IntroductionSystem Configuration Outline of the DC Power System is illustrated in FigureConfiguration Cabinet dimension % 0.6 % 0.6 m % 0.6 % 0.4 m Configurations of Actura Flex 48330 Power SystemSCU BCU Rectifier Shelf ComponentsOutline Connector board Dimension of Rectifier Shelf are given in TableDimensions of rectifier shelf Manufacture type Wmm ×Dmm ×HmmDimensions RectifierMulti-Communication mode Function of indicatorsDimension H % W % D132mm % 85mm % 287mm Weight 0.76kg 3 SCUAlarm category settings for dry contact output Functions fulfilled by SCU and MCLevel Authority Default password Password protection for important operationsAuthority and default password Multi-Function Unit MFUAlarm output Battery Connection Unit BCUConfiguration of MFU Component Description0m % 0.6m % 0.6m cabinet BCU configurationSystem Cabinet 0m % 0.6m % 0.4m cabinetPower Supply InstallationInstallation Preparation Environmental conditions in power roomSite Survey Tools & MaterialUnpacking Installation on the floor Installation ProceduresCabinet Installation Drill reserve holesInstalling expansive pipe Connection requirements External Electrical Connection InterfaceConnection Of Input Cables AC input modesConnection of input terminals Different cable connection modesConnection of single-phase AC power input Connection Of Load Cables Configuration number of load MCBs and battery MCBsBusbar type Max. load number 12 Connector board in rectifier shelf Connection Of Communication CablesLayout Of Connector Board S6415X2 13 Layout of connector board S6415X2Interface definition of connector board S6415X2 Interface Definition Of Connector Board S6415X2Connector Pin Signal name Mark number Logic relation Pgng POWER+ Power Connection Of Temperature Sensor CablesConnector Pin Signal name Connection With ModemConnecting method Battery Installation And CablingBattery Installation Connection With Dry ContactsBattery Cable Connection Standard configuration16 Connection of battery cables Non-standard configuration 18 Negative battery cables connection in BCUParallel Connection Of Cabinets DC/Parallel connectionsStartup Check the DC Power System according to -1 before startupSystem checklist before startup Checking Before StartupParameters Configuration Startup ProcessTesting Rectifier TestingTesting MFU Testing SCUBCU Test Battery Breaker TestLoad Breaker Test Operation Panel Functions of LED indicatorsOperating SCU Functions of SCU keysOperation Procedures First system information page appearsQuerying System Status First Page Of System InformationBattery information Other System Information ScreenBC prompt and temperature information AC informationQuerying Rectifier Status Querying Alarms And Setting Alarm Plans Querying Active AlarmQuery Alarm History Alarm History Alarm Type Table Alarm type tableLlvd BlvdChapter Operating SCU Serial Alarm Description Default Setting Alarm Type For Dry Contacts Changing Audible/Visual Alarm And Alarm Call Back PlanChanging Alarm Types Of Dry Contacts Changing audible/visual alarm and alarm call back planOptional alarm types Alarm type RemarkSet the Alarm Names Through PLC Function PLC SN and Alarm Logic matrix used for configuring 8 dry contactsExample of PLC setting Alarm Remark DescriptionAlarm Remark Description PLCMaintenance Llvd BlvdOperating SCU Parameter Setting Method Setting System ParametersPress ESC to return to the menu of higher level Password levels and authorities Level AuthorityBatt. Selection First page of the Batt. Selection is shown belowLVD Parameter Description Charging Management Parameters There are 6 related pages, as shown belowOperating SCU BC/FC switchover diagram is shown below Parameter Range Default Value description12 Charging management parameter value description Battery Test Parameters There are 7 related pages, as shown belowSchematic diagram of the test function is shown below 13 Value description of the battery test parametersValue description of the parameters is listed below Temperature Compensation Coefficient Parameters First page of the setting interface is shown belowAC Settings Configuration interface is shown belowDC Setting There are three related pages, as shown belowRect Settings 17 Value description of rectifier settingsSystem Settings There will be a prompt when resetting the system 18 Value description of system settings EEM-MModel description is shown below 48V/50A/SET/NONE 48V/30A/SET/NONEFirst page of the setting interface is show below Alarm SettingsPower system model System type 19 Relationship between system model and system type20 Value description of alarm settings Maintenance Of SCU Routine MaintenanceMaintenance Of Rectifier Maintenance Of MFUCover Plates Battery MaintenanceStore the battery in a cool dry place Storage And SupplementaryReplacement Troubleshooting TroubleshootingTroubleshooting Rectifier Symptom Cause SuggestionMains Failure Disastrous AccidentsParameter Category Appendix System Technical ParametersEMC Mtbf Appendix 2 Engineering Design Diagram Appendix 2 Engineering Design Diagram Connector Connector specs MCBAppendix 3 System Circuit Diagram Appendix 3.1 System Electric Schematic DiagramAppendix 3.2 System Wiring Diagram Appendix 3.3 MFU Electric Wiring Diagram Appendix 3.4 BCU Electric Wiring Diagram Hvsd Appendix GlossaryAbbreviation Full word LVD