Xerox 3 manual Printer System Administrator Guide to correct

Page 17

Windows NT 4.x Network

19

20

21

If the printer will not be shared, click Next>. To share the printer, enter a Share Name, check the share checkbox, then click Next>.

At the next dialog it is recommended that you print a test page. Click Finish.

Wait for the Test Print to print. A new dialog will ask for confirmation of the test print, click Yes.

22	Send a print job to the printer.
23	Check the print job for print quality. If print quality
	problems exist, use the print quality section of your
	printer System Administrator Guide to correct the
	problem.
24	If your print job did not print, see the Troubleshooting
	section for your operating system in the Technical

Information Guide to correct the problem.

Printers connected to a Windows NT network with TCP/IP protocol enabled can use a Web Browser to monitor and configure your printer. Refer to the section in this document entitled Internet Printer Services.

For installing or managing multiple printers on a Windows NT network with TCP/IP protocol enabled, you can use the Xerox CentreWare MC snap-in to Microsoft Management Console.

Refer to the Xerox CentreWare MC Users Guide.

Quick Network Install Guide ❖ 17

Image 17

Contents DocuPrint Quick Network Install Guide Quick Network Install Guide Contents Contents Requirements Additional information Purpose of This DocumentPrinter System Administrator Guide to correct How to Use this DocumentNetworked Printers Windows 95/98 Peer-to-Peer NetworkFound in the printer CD ROM Instruction booklet NextWindows 95/98 Peer-to-Peer Network Windows 95/98 Peer-to-Peer Network Quick Install Steps To change the group name in a NetBEUI-only network Type yes to confirm the monitor session Windows 95/98 Users Introduction Preliminary Steps Windows NT 4.x NetworkClick Add Port TCP/IP ProtocolAdd printer Wizard starts Click New Port Printer System Administrator Guide to correct Select the Hewlett-Packard Network Port Quick Install StepsDLC/LLC Protocol If the printer will not be shared, click Next. To share Port AppleTalk ProtocolSelect the AppleTalk Printing Devices and click New CD Drive\instal\winnt40 then click Open Windows 2000 Network Inside the Network and Dial-up Connections window Click in the Printer Name or IP Address edit box, Select Standard TCP/IP Port from the New Port TypeWindows 2000 Network Windows 2000 Network Select the Hewlett-Packard Network Port from the New DLC/LLC ProtocolPage. Click Next Printer System Administrator Guide to correct Select the AppleTalk Printing Devices from the New Network and Dial-up Connections window and secectProperties Next Printer System Administrator Guide to correct Sheet Document in Appendix a Print The ConfigurationMacintosh EtherTalk Network Novell NetWare 3.1x, 4.1x Networks Quick SetupPrinter System Administrator Guide to correct the problem Novell NetWare 3.1x, 4.1x, 5.x Networks Are found in the Technical Information Guide OS/2 Warp Server LAN Server NetworkOS/2 Warp V4.0 OS/2 Warp Connect Peer-to-Peer Network IBM AIX Unix NetworkAvailable on the Printer Management Software CD-ROM Go to Appendix B Set an IP Address and perform oneSunos and Solaris Refer to the CentreWare DP user Internet Printer Services Configure your Web Browser For DocuPrint Networked Printers Appendix a Print Configuration SheetPress Enter. The Configuration Sheet will be printed Appendix B Set an IP Address RARP/BOOTPStatic Addressing Appendix B Set an IP Address Dynamic Addressing RARP/BOOTP Dynamic Addressing Dhcp Document entitled Appendix a Print The Configuration Sheet Dynamic Addressing Dhcp or RARP/BOOTP Type Telnet x.x.x.x CR Arp -s x.x.x.x aa-aa-aa-aa-aa-aa CRArpbypass set name 0x00.0x00.0x81.0xa.0xa.0xa AT&T and NCR X.x nameArp -s ether name 0081aaa no leading zeros RS-6000 Appendix B Set an IP Address Quick Network Install Guide

Related manuals

Manual 4 pages 48.38 Kb