Xerox 3 manual Dynamic Addressing Dhcp or RARP/BOOTP

Page 51

For the CentreDirect

External Print Server

(External Ethernet

Adapter)

Appendix B: Set an IP Address

Dynamic Addressing (DHCP or RARP/BOOTP)

The CentreDirect External Print Server (External Ethernet Adapter) comes from the factory with DHCP and BOOTP/RARP enabled. If you have any of these IP resolution methods on your network, the CentreDirect External Print Server (External Ethernet Adapter) will automatically acquire a TCP/IP address from the server.

1

Connect power to the CentreDirect External Print Server

 

(External Ethernet Adapter).

2

The CentreDirect External Print Server (External

 

Ethernet Adapter) will automatically acquire an IP

 

address from the server. Depending on your network, the

 

time required may vary. When the CentreDirect External

 

Print Server (External Ethernet Adapter) acquires an

 

address, the SYS light will flash 1/second.

3

Once an IP address has been acquired, the CentreDirect

 

External Print Server (External Ethernet Adapter) will

print a configuration page.

To disable printing a configuration page, move both DIP switches to the UP position.

Quick Network Install Guide ❖ 51

Page 50 Page 52
Image 51
Page 50 Page 52
Contents DocuPrint Quick Network Install Guide Quick Network Install Guide Contents Contents Requirements Additional information Purpose of This DocumentPrinter System Administrator Guide to correct How to Use this DocumentNext Windows 95/98 Peer-to-Peer NetworkNetworked Printers Found in the printer CD ROM Instruction bookletWindows 95/98 Peer-to-Peer Network Windows 95/98 Peer-to-Peer Network Quick Install Steps To change the group name in a NetBEUI-only network Type yes to confirm the monitor session Windows 95/98 Users Introduction Preliminary Steps Windows NT 4.x NetworkTCP/IP Protocol Add printer Wizard startsClick Add Port Click New Port Printer System Administrator Guide to correct Quick Install Steps DLC/LLC ProtocolSelect the Hewlett-Packard Network Port If the printer will not be shared, click Next. To share AppleTalk Protocol Select the AppleTalk Printing Devices and click NewPort CD Drive\instal\winnt40 then click Open Windows 2000 Network Inside the Network and Dial-up Connections window Click in the Printer Name or IP Address edit box, Select Standard TCP/IP Port from the New Port TypeWindows 2000 Network Windows 2000 Network Select the Hewlett-Packard Network Port from the New DLC/LLC ProtocolPage. Click Next Printer System Administrator Guide to correct Network and Dial-up Connections window and secect PropertiesSelect the AppleTalk Printing Devices from the New Next Printer System Administrator Guide to correct Document in Appendix a Print The Configuration Macintosh EtherTalk NetworkSheet Novell NetWare 3.1x, 4.1x Networks Quick SetupPrinter System Administrator Guide to correct the problem Novell NetWare 3.1x, 4.1x, 5.x Networks Are found in the Technical Information Guide OS/2 Warp Server LAN Server NetworkOS/2 Warp V4.0 OS/2 Warp Connect Peer-to-Peer Network IBM AIX Unix NetworkGo to Appendix B Set an IP Address and perform one Sunos and Solaris Refer to the CentreWare DP userAvailable on the Printer Management Software CD-ROM Internet Printer Services Configure your Web Browser For DocuPrint Networked Printers Appendix a Print Configuration SheetPress Enter. The Configuration Sheet will be printed Appendix B Set an IP Address RARP/BOOTPStatic Addressing Appendix B Set an IP Address Dynamic Addressing RARP/BOOTP Dynamic Addressing Dhcp Document entitled Appendix a Print The Configuration Sheet Dynamic Addressing Dhcp or RARP/BOOTP Type Telnet x.x.x.x CR Arp -s x.x.x.x aa-aa-aa-aa-aa-aa CRX.x name Arp -s ether name 0081aaa no leading zeros RS-6000Arpbypass set name 0x00.0x00.0x81.0xa.0xa.0xa AT&T and NCR Appendix B Set an IP Address Quick Network Install Guide
Related manuals
Manual 4 pages 48.38 Kb
Top Page Image Contents