Xerox 3 manual Press Enter. The Configuration Sheet will be printed

Page 44

Appendix A: Print The Configuration Sheet

For CenterDirect

External Print Server

(External Ethernet

Adapter)

3

Press Enter. The Configuration Sheet will be printed.

4

Review the current settings and make any modifications

 

necessary for your network application.

1

Set the DIP switches on the rear of the CentreDirect

 

External Print Server (External Ethernet Adapter) to

 

Switch 1=UP, Switch 2 = DOWN.

2

Unplug the power cord from the CentreDirect External

 

Print Server (External Ethernet Adapter).

3

Wait 5 seconds and reattach the power cord.

4

The CentreDirect External Print Server (External Ethernet

 

Adapter) will print a configuration page after

approximately 15 seconds.

To disable printing a configuration page, move both DIP switches to the UP position.

Resetting the CentreDirect External Print Server (External Ethernet Adapter)

1

2

Unplug the power cord from the CentreDirect External Print Server (External Ethernet Adapter).

Wait 5 seconds and reattach the power cord.

44 Quick Network Install Guide

Image 44
Contents DocuPrint Quick Network Install Guide Quick Network Install Guide Contents Contents Purpose of This Document Requirements Additional informationHow to Use this Document Printer System Administrator Guide to correctWindows 95/98 Peer-to-Peer Network Networked PrintersFound in the printer CD ROM Instruction booklet NextWindows 95/98 Peer-to-Peer Network Windows 95/98 Peer-to-Peer Network Quick Install Steps To change the group name in a NetBEUI-only network Type yes to confirm the monitor session Windows 95/98 Users Windows NT 4.x Network Introduction Preliminary StepsClick Add Port TCP/IP ProtocolAdd printer Wizard starts Click New Port Printer System Administrator Guide to correct Select the Hewlett-Packard Network Port Quick Install StepsDLC/LLC Protocol If the printer will not be shared, click Next. To share Port AppleTalk ProtocolSelect the AppleTalk Printing Devices and click New CD Drive\instal\winnt40 then click Open Windows 2000 Network Inside the Network and Dial-up Connections window Select Standard TCP/IP Port from the New Port Type Click in the Printer Name or IP Address edit box,Windows 2000 Network Windows 2000 Network DLC/LLC Protocol Select the Hewlett-Packard Network Port from the NewPage. Click Next Printer System Administrator Guide to correct Select the AppleTalk Printing Devices from the New Network and Dial-up Connections window and secectProperties Next Printer System Administrator Guide to correct Sheet Document in Appendix a Print The ConfigurationMacintosh EtherTalk Network Quick Setup Novell NetWare 3.1x, 4.1x NetworksPrinter System Administrator Guide to correct the problem Novell NetWare 3.1x, 4.1x, 5.x Networks OS/2 Warp Server LAN Server Network Are found in the Technical Information GuideOS/2 Warp V4.0 OS/2 Warp Connect Peer-to-Peer Network Unix Network IBM AIXAvailable on the Printer Management Software CD-ROM Go to Appendix B Set an IP Address and perform oneSunos and Solaris Refer to the CentreWare DP user Internet Printer Services Configure your Web Browser Appendix a Print Configuration Sheet For DocuPrint Networked PrintersPress Enter. The Configuration Sheet will be printed RARP/BOOTP Appendix B Set an IP AddressStatic Addressing Appendix B Set an IP Address Dynamic Addressing RARP/BOOTP Dynamic Addressing Dhcp Document entitled Appendix a Print The Configuration Sheet Dynamic Addressing Dhcp or RARP/BOOTP Arp -s x.x.x.x aa-aa-aa-aa-aa-aa CR Type Telnet x.x.x.x CRArpbypass set name 0x00.0x00.0x81.0xa.0xa.0xa AT&T and NCR X.x nameArp -s ether name 0081aaa no leading zeros RS-6000 Appendix B Set an IP Address Quick Network Install Guide
Related manuals
Manual 4 pages 48.38 Kb