Xerox 3 manual OS/2 Warp V4.0 OS/2 Warp Connect Peer-to-Peer Network

Page 38

OS/2 Warp V4.0 and OS/2 Warp Connect 3.0 Peer-to-Peer Network

OS/2 Warp V4.0 and

OS/2 Warp Connect 3.0

Peer-to-Peer Network

Quick Install Steps	1
	2

3

4

5

6

7

Print the Configuration Sheet. Details are in this document in Appendix A: Print The Configuration

Sheet.

Check the Configuration Sheet and verify that both TCP/IP protocol and proper connector are enabled on the printer.

Create a new printer to load print drivers. Details for this are found in the Technical Information Guide.

Create a printer share and its access permissions (sharing and connecting).

Start LPRPORTD/LPRMON, ping printer, open EPM and send a print job to the printer.

Check the print job for print quality. If print quality problems exist, use the print quality section of your printer System Administrator Guide to correct the problem.

If your print job did not print, see the Troubleshooting section for your operating system in the Technical Information Guide to correct the problem.

38 ❖ Quick Network Install Guide

Image 38

Contents DocuPrint Quick Network Install Guide Quick Network Install Guide Contents Contents Purpose of This Document Requirements Additional informationHow to Use this Document Printer System Administrator Guide to correctFound in the printer CD ROM Instruction booklet Windows 95/98 Peer-to-Peer NetworkNetworked Printers NextWindows 95/98 Peer-to-Peer Network Windows 95/98 Peer-to-Peer Network Quick Install Steps To change the group name in a NetBEUI-only network Type yes to confirm the monitor session Windows 95/98 Users Windows NT 4.x Network Introduction Preliminary StepsClick Add Port TCP/IP ProtocolAdd printer Wizard starts Click New Port Printer System Administrator Guide to correct Select the Hewlett-Packard Network Port Quick Install StepsDLC/LLC Protocol If the printer will not be shared, click Next. To share Port AppleTalk ProtocolSelect the AppleTalk Printing Devices and click New CD Drive\instal\winnt40 then click Open Windows 2000 Network Inside the Network and Dial-up Connections window Select Standard TCP/IP Port from the New Port Type Click in the Printer Name or IP Address edit box,Windows 2000 Network Windows 2000 Network DLC/LLC Protocol Select the Hewlett-Packard Network Port from the NewPage. Click Next Printer System Administrator Guide to correct Select the AppleTalk Printing Devices from the New Network and Dial-up Connections window and secectProperties Next Printer System Administrator Guide to correct Sheet Document in Appendix a Print The ConfigurationMacintosh EtherTalk Network Quick Setup Novell NetWare 3.1x, 4.1x NetworksPrinter System Administrator Guide to correct the problem Novell NetWare 3.1x, 4.1x, 5.x Networks OS/2 Warp Server LAN Server Network Are found in the Technical Information GuideOS/2 Warp V4.0 OS/2 Warp Connect Peer-to-Peer Network Unix Network IBM AIXAvailable on the Printer Management Software CD-ROM Go to Appendix B Set an IP Address and perform oneSunos and Solaris Refer to the CentreWare DP user Internet Printer Services Configure your Web Browser Appendix a Print Configuration Sheet For DocuPrint Networked PrintersPress Enter. The Configuration Sheet will be printed RARP/BOOTP Appendix B Set an IP AddressStatic Addressing Appendix B Set an IP Address Dynamic Addressing RARP/BOOTP Dynamic Addressing Dhcp Document entitled Appendix a Print The Configuration Sheet Dynamic Addressing Dhcp or RARP/BOOTP Arp -s x.x.x.x aa-aa-aa-aa-aa-aa CR Type Telnet x.x.x.x CRArpbypass set name 0x00.0x00.0x81.0xa.0xa.0xa AT&T and NCR X.x nameArp -s ether name 0081aaa no leading zeros RS-6000 Appendix B Set an IP Address Quick Network Install Guide

Related manuals

Manual 4 pages 48.38 Kb