Xerox 3 manual How to Use this Document, Printer System Administrator Guide to correct

Page 6

Purpose of This Document

How to Use this

Document

This document has been arranged to get the printer set up on your network quickly and with minimum reading.

1

Review the Table of Contents.

2

Find the network operating systems (NOS), which

 

pertains to your network.

3

Go to the page indicated and perform the procedure. The

 

procedure may point you to one or more of the

 

Appendices located in the rear of this document.

4

Once these procedures are finished it is recommended

 

you print a test page.

5

Check the print job for print quality. If print quality

 

problems exist, use the Troubleshooting section of your

 

printer System Administrator Guide to correct the

 

problem.

6

If your print job did not print, see the Troubleshooting

 

section for your operating system in the Technical

Information Guide to correct the problem.

DocuPrint printers come with an imbedded Web Server. If you wish to monitor or administer your printer using your standard Web Browser software perform the procedures in the section entitled Internet Printer Services .

6 Quick Network Install Guide

Image 6
Contents DocuPrint Quick Network Install Guide Quick Network Install Guide Contents Contents Purpose of This Document Requirements Additional informationHow to Use this Document Printer System Administrator Guide to correctFound in the printer CD ROM Instruction booklet Windows 95/98 Peer-to-Peer NetworkNetworked Printers NextWindows 95/98 Peer-to-Peer Network Windows 95/98 Peer-to-Peer Network Quick Install Steps To change the group name in a NetBEUI-only network Type yes to confirm the monitor session Windows 95/98 Users Windows NT 4.x Network Introduction Preliminary StepsTCP/IP Protocol Add printer Wizard startsClick Add Port Click New Port Printer System Administrator Guide to correct Quick Install Steps DLC/LLC ProtocolSelect the Hewlett-Packard Network Port If the printer will not be shared, click Next. To share AppleTalk Protocol Select the AppleTalk Printing Devices and click NewPort CD Drive\instal\winnt40 then click Open Windows 2000 Network Inside the Network and Dial-up Connections window Select Standard TCP/IP Port from the New Port Type Click in the Printer Name or IP Address edit box,Windows 2000 Network Windows 2000 Network DLC/LLC Protocol Select the Hewlett-Packard Network Port from the NewPage. Click Next Printer System Administrator Guide to correct Network and Dial-up Connections window and secect PropertiesSelect the AppleTalk Printing Devices from the New Next Printer System Administrator Guide to correct Document in Appendix a Print The Configuration Macintosh EtherTalk NetworkSheet Quick Setup Novell NetWare 3.1x, 4.1x NetworksPrinter System Administrator Guide to correct the problem Novell NetWare 3.1x, 4.1x, 5.x Networks OS/2 Warp Server LAN Server Network Are found in the Technical Information GuideOS/2 Warp V4.0 OS/2 Warp Connect Peer-to-Peer Network Unix Network IBM AIXGo to Appendix B Set an IP Address and perform one Sunos and Solaris Refer to the CentreWare DP userAvailable on the Printer Management Software CD-ROM Internet Printer Services Configure your Web Browser Appendix a Print Configuration Sheet For DocuPrint Networked PrintersPress Enter. The Configuration Sheet will be printed RARP/BOOTP Appendix B Set an IP AddressStatic Addressing Appendix B Set an IP Address Dynamic Addressing RARP/BOOTP Dynamic Addressing Dhcp Document entitled Appendix a Print The Configuration Sheet Dynamic Addressing Dhcp or RARP/BOOTP Arp -s x.x.x.x aa-aa-aa-aa-aa-aa CR Type Telnet x.x.x.x CRX.x name Arp -s ether name 0081aaa no leading zeros RS-6000Arpbypass set name 0x00.0x00.0x81.0xa.0xa.0xa AT&T and NCR Appendix B Set an IP Address Quick Network Install Guide
Related manuals
Manual 4 pages 48.38 Kb