Canon 2010F manual Platen Glass, Lift up the feeder, Place your original face down

Page 21

1

Introduction to Copying

Platen Glass

You should use the platen glass when scanning bound originals (such as books and magazines), originals on heavy or lightweight paper, and transparencies into memory.

1 Lift up the feeder.

IMPORTANT

This machine is equipped with an open/close sensor on the underside of the feeder (see circled area in the above illustration). When placing originals on the platen glass, lift the feeder about 11 7/8" (30 cm) so that the sensor detaches from the underside of the feeder. If the sensor does not detach from the underside of the feeder, the size of originals may not be detected correctly.

2 Place your original face down.

The surface that you want to scan into memory must be placed face down. Align the top edge of your original with the back edge of the platen glass (by the arrow in the top left corner).

Place books and other bound originals on the platen glass in the same way.

1-12Placing Originals

Image 21

Contents Copying Guide ImageRUNNER 2010F Copying Guide Manuals for the Machine Appendix How This Manual Is OrganizedContents Special Copying Features Customizing SettingsAppendix How to Use This Manual Symbols Used in This ManualKeys Used in This Manual Vii Illustrations Used in This ManualTrademarks Legal NoticesCopyright DisclaimersIntroduction to Copying Copy Basic Features Screen Special Features ScreenOverview of the imageRUNNER 2010F Additional Functions Menu Press Copy Flow of Copy OperationsIf the message Insert a Control Card appears If the message Enter Department ID and Password appearsPlace your original Set the desired copy mode on the Copy Basic Features screenSet the desired copy modes on the Special Features screen Enter the copy quantityPress Start If you want to cancel a copy job in the standby mode If you want to stop a copy jobIf you want to interrupt a copy job If you have set Department ID Management, press ID Placing Originals Platen GlassFeeder Vertical Placement Vertical Placement Horizontal Placement FeederOrientation Platen GlassPlaten Glass Lift up the feederPlace your original face down Gently lower the feeder Feeder ADF-J1 Original Output Tray Adjust the slide guides to ﬁt the size of your originalsUsing the Stop Key Canceling a Copy JobPress Stop If only one copy job is being processedYou cannot select multiple jobs and cancel them all at once Using the System Monitor ScreenPress Monitor Press F3 YESReserving Copy Jobs While Printing Reserved CopyingPlace your original, and set the desired copy modes Copy lightsWhen scanning is complete, remove the original from Machine Press Interrupt Interrupt ModeOnce the original is scanned, remove it from the machine 22Interrupt Mode Basic Copying Features Copy Quantity Specifying the Required Number of CopiesChanging the Copy Quantity Copy Quantity Automatic Paper Selection Paper SelectionMake sure that Auto Paper is selected press OK Manual Paper SelectionIf you want to use the stack bypass Press F3 or F4 to select the desired paper sizePress OK Copy Exposure Manual Text Mode Text/Photo ModeImage Quality Manual Copy Exposure and Image Quality AutomaticPress F1 Light or F3 Dark to adjust the exposure Copy Exposure ManualPress Light or Text/Photo Mode Text ModePhoto Mode Image Quality ManualCopy Exposure and Image Quality Automatic Press F2 Auto Exposur OK To cancel the automatic exposure control, pressChanging the Copy Zoom Ratio Preset ZoomZoom by Percentage Auto ZoomPreset Zoom ReduceEnlarge Zoom by Percentage Press F3 Reduce or F4 Enlarge to select a presetReduction or enlargement ratio press OK Each time you press200%. Enter a value within the setting range Set the copy ratio using the numeric keys press OKAuto Zoom Correct valuePress F2 Auto Zoom OK Press F1 Copy RatioOptional Units Collate Rotate Offset Staple*1 Collating CopiesIf the Collate Mode Is Set If the Rotate Mode Is SetOriginals Set Result If the Staple Mode Is Set If the Offset Mode Is SetOrder Collate Place your originals press CollateIf you want to set the Offset mode If you want to set the Rotate modeAppears Order StapleLights Number of Copies, on pPress Start 24Collating Copies Special Copying Features Features Two-Page SeparationPlace your original on the platen glass press Special Original Size setting menu appears Direction that the book opens press OKSpecial Press F4 Orignal Size to select the paper size press OK Place your original press Special Features Margin ModeOriginal Left Margin Selected Right Margin Top Margin Bottom Margin Selected Selected6Margin Mode Press YES or Original Frame Erase Frame EraseOriginal Frame Erase Book Frame Erase Mode Original Selected Copy Not SelectedBook Frame Erase Hole Punch ErasePress F4 Orignal Size to select the size of the original Book Frame Erase Opened press OK Press F3 Frame Erase Press F3 Book FR ERS OKPress F3 or F4 + to set the desired book frame erase Default setting is ‘10 mm’Width 3 mm to 50 mm for the center line press OK Clear to clear the valuePress F3 Frame Erase Press F4 HOLE/P Erase OK Hole Punch EraseEach time you press 16Frame Erase Image Combination Original Vertical Placement CopyCopying Special Place your originals press Special FeaturesBecomes highlighted Copy Layout setting menu appears Paper size press OK If you selected 2 on 1 Comb in stepIf you selected 4 on 1 in step Press Start Different Size Originals To 4 where you registered the Different Size OriginalsMode Place your originals in the feeder press the Shortcut keySet the desired copy modes 24Different Size Originals Customizing Settings Available Settings Applicable Copy Settings TableChanging the Current Standard Settings Image Quality and Copy ExposurePress Additional Functions Press Reset to return to the Copy Basic Features screen Press F3 or F4 to highlight 01 STD Image QualEXP press OK Press F3 or F4 to highlight 02 STD Zoom Ratio Press OK Zoom RatioPress F3 or F4 to highlight 03 Standard Copy QTY press OK Copy QuantityFrame Erase Width Press F3 or F4 to highlight 04 Frame EraseWidth press OK Auto Sort Press F2 or F3 + to set the desired frame erase widthMm to 20 mm press OK Sort Rotate Press F3 or F4 to highlight 05 Auto Sort Press OKPress F3 or F4 to select 01 on or 02 OFF Press OK Press F3 or F4 to highlight 06 Sort Rotate press OK Dull SharpnessSharp Original Copy Dull Is Set Dull Is Not SetPress F3 or F4 to highlight 08 Sharpness press OK Prescan Press F3 or F4 to highlight 09 Prescan press F4OKIf you want to use the prescan function, select 01 on 14Changing the Current Standard Settings Assigning Functions Using Shortcut KeysPress F3 or F4 to select a shortcut key press OK Press F3 or F4 to highlight 07 Shortcut KEY SET press OKIf necessary, specify the settings for each mode That contains the copy mode you want to setSetting Applicable Making Copies18Using Shortcut Keys Appendix Function to Be Set Combination of Functions ChartCombination available Combination unavailable 4Combination of Functions Chart Originals Size Different Numerics IndexIndex Making Copies Canon Italia S.p.A Canon Deutschland GmbH

Related manuals

Manual 382 pages 14.98 Kb