Belkin F1DP116G, F1DP108G user manual Information, How to get service

Page 83

Information

How to get service.

To get service for your Belkin product you must take the following steps:

1.Contact Belkin Corporation at 501 W. Walnut St., Compton CA 90220, Attn: Customer Service, or call (800)-223-5546, within 15 days of the Occurrence. Be prepared to provide the following information:

a.The part number of the Belkin product.

b.Where you purchased the product.

c.When you purchased the product.

d.Copy of original receipt.

2.Your Belkin Customer Service Representative will then instruct you on how to forward your receipt and Belkin product and how to proceed with your claim.

Belkin Corporation reserves the right to review the damaged Belkin product. All costs of shipping the Belkin product to Belkin Corporation for inspection shall be borne solely by the purchaser. If Belkin determines, in its sole discretion, that it is impractical to ship the damaged equipment to Belkin Corporation, Belkin may designate, in its sole discretion, an equipment repair facility to inspect and estimate the cost to repair such equipment. The cost, if any, of shipping the equipment to and from such repair facility and of such estimate shall be borne solely by the purchaser. Damaged equipment must remain available for inspection until the claim is finalized. Whenever claims are settled, Belkin Corporation reserves the right to be subrogated under any existing insurance policies the purchaser may have.

How state law relates to the warranty.

THIS WARRANTY CONTAINS THE SOLE WARRANTY OF BELKIN CORPORATION, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR, EXCEPT AS REQUIRED BY LAW, IMPLIED, INCLUDING THE IMPLIED WARRANTY OR CONDITION OF QUALITY, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, AND SUCH IMPLIED WARRANTIES, IF ANY, ARE LIMITED IN DURATION TO THE TERM OF THIS WARRANTY.

Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you.

IN NO EVENT SHALL BELKIN CORPORATION BE LIABLE FOR INCIDENTAL, SPECIAL, DIRECT, INDIRECT, CONSEQUENTIAL OR MULTIPLE DAMAGES SUCH AS, BUT NOT LIMITED TO, LOST BUSINESS OR PROFITS ARISING OUT OF THE SALE OR USE OF ANY BELKIN PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

This warranty gives you specific legal rights, and you may also have other rights, which may vary from state to state. Some states do not allow the exclusion or limitation of incidental, consequential, or other damages, so the above limitations may not apply to you.

1

2

3

4

5

6

7

8

9

10

section

79

Image 83
Contents OmniView SMB KVM-over-IP Switch Page Table of Contents Using the Switch from a Local Console Using the Switch from a Remote ConsoleIntroduction Package ContentsOverview Remote-Management FeaturesOther Features Interface Modules Equipment RequirementsServer Interface Modules OmniView SMB ServerBelkin UTP Patch Cables CablesSystem Requirements Back View Unit Display DiagramsFront View Specifications SMB Server Interface Module, PS/2 VGA-Cable Length MiniDIN8-Cable Length SMB Server Interface Module, USBSMB Server Interface Module, Legacy Sun VGA-Cable Length USB-Cable LengthWhere to place the Switch Local InstallationPre-Configuration Cable-Distance Requirements for PS/2, USB, and Sun Servers Mounting the Switch Local InstallationConnecting the Console to the Switch Local Installation Connecting Servers to the Switch PS/2 Connection Local Installation Connecting Servers to the Switch USB Connection Local Installation Connecting Servers to the Switch Sun MiniDIN8 Connection Local Installation Powering Up the Systems How to Assign a Bank Address Daisy-Chaining Multiple KVM Switches OptionalDIP SWITCH# SMB CAT5 Bank Address BANK-DIP-Switch-Configuration Chart SMB CAT5 KVM SwitchesExample of Daisy-Chain Configuration Getting Started Connecting the Primary and Secondary KVM SwitchesConnecting the servers Identifying the IP Address Remote InstallationTo log into the web interface Logging into the Web InterfaceRemote Installation First TCP Port Network ConfigurationDevice Name Set a Static IP Enable DhcpUser User SettingsAdministrator To add a new user View OnlyTo block a user To edit a userTo delete a user Blocking a standard user and View Only userSwitch-Configuration Switch ConfigurationTo specify and name servers Installing new Switch-Definition Files SDFsTo install the SDF To configure your serial device Serial SettingsAccount Blocking Security SettingsPassword Policy SSL Certificate Idle TimeoutTo install an SSL certificate Firmware Upgrade To upgrade firmware MaintenanceLogging Out Restore Factory SettingsTo restore factory settings To start a remote session Using the Switch from a Remote ConsoleStarting a Remote Session To work in full-screen mode Full-Screen ModeDisconnecting the Remote Session Using the Quick-Access ToolbarMoving or Hiding the Quick-Access Toolbar Mouse-Pointer Calibration Mouse Configuration and SettingsMouse-Pointer Alignment To align mouse pointersTo manually synchronize mouse pointers Manual SettingsYou must manually synchronize the mouse pointers if Mouse-Pointer Options Windows XP USB OptionAdvanced-Mouse Emulation To change the mouse-emulation settingsTo add a keyboard sequence Keyboard Configuration and SettingsTo transmit a keyboard sequence Add-Special-Key Box To record a keyboard sequenceTo adjust the video manually Video Configuration and SettingsManual Video Adjust To refresh the video settingsTo adjust the video automatically Auto Video AdjustTo change the bandwidth settings Performance Settings BandwidthTo connect to a different server Selecting a ServerAdditional Features To restore factory defaults Restoring Factory DefaultsSelecting a Server or Bank Using the Switch from a Local ConsoleSelecting a Server or Bank Using Hot Keys Down Selecting a Bank Using Scroll Buttons Selecting a Server Using Port SelectorsAutoScan Mode Main OSD-Menu On-Screen Display OSDFunction/Help OSD-Menu Keyboard CommandsScan Time Function/Help-Page Keyboard CommandsAdmin Password ScanHot Key TimeoutMonitor-DDC2 Feature Hot-Key-Command Shortcuts Sun Key Combo Key Sun Combo KeysUpdating Firmware Can I use the Switch on my Sun server that supports USB? Frequently Asked QuestionsFrequently Asked Questions General ProblemSolution Local ConsoleMouse KeyboardUSB Remote Console Video quality is bad and/or grainy Glossary Section FCC Statement Belkin Corporation Limited 2-Year Product WarrantyInformation How to get serviceBelkin Tech Support
Related manuals
Manual 84 pages 11.57 Kb