Star Micronics TSP800 user manual Parallel Interface Type, Star Page mode

Page 105

B-1. Parallel Interface Type

ON

OFF

No. 1 2 3 4 5 6 7 8

DIP-SW1

ON

OFF

No. 1 2 3 4

DIP-SW2

DIP-SW 1

Switch 1-1	Switch 1-2	Command emulation
ON	ON	Star Line Mode
OFF	ON	Star Page Mode

ON	OFF	DP8340 Mode

The factory settings of DIP switch are all on.

The functions of switches 1-3 through 1-8 will change according to the command emulation that has been set using switches 1-1 and 1-2.

(1) Star Line mode

Switch	Function		ON	OFF

1-1	Command emulation		Always ON
						APPENDIX
1-2	Command emulation		Always ON			APPENDIX
1-2	Command emulation		Always ON

1-3	Should not be changed (Should be set to on)

1-4	Sensor adjustment		Invalid	Valid

1-5	Pin #31 (INIT) reset signal		Valid	Invalid

1-6	Handshaking conditions		Offline or receive	Receive buffer full
1-6	Handshaking conditions		Offline or receive	Receive buffer full
	(conditions for BUSY)		buffer full

1-7	Automatic status back function		Invalid	Valid

1-8	Should not be changed (Should be set to on)

(2) Star Page mode

Switch	Function		ON	OFF

1-1	Command emulation		Always OFF

1-2	Command emulation		Always ON

1-3	Should not be changed (Should be set to on)

1-4	Sensor adjustment		Invalid	Valid

1-5	Pin #31 (INIT) reset signal		Valid	Invalid

1-6	Handshaking conditions		Offline or receive	Receive buffer full
	(conditions for BUSY)		buffer full

1-7	Automatic status back function		Invalid	Valid

1-8	Should not be changed (Should be set to on)

– 102 –

Image 105

Contents TSP800 Series EC Council Directive 89/336/EEC of 3 May Table of Contents Standard Model Parts Identification and NomenclatureWall Mount/Stand Model Mounting hardware for wall mount model Choosing a place for the printerSpecifications of the wall mounting bracket Mounting the bracket for the wall mount modelEspecially in front of the printer Wood structure wall Concrete structure wall Nippon Paper Industries Paper thickness Core outerDC24±5%, 2.0 a 5.0 a Load 10 sec. Max Connecting Cables and AC Adapter Connecting the Interface Cable Connecting to a Peripheral Unit Connecting the Optional AC Adapter Turning Power On Control Panel ErrorsNon recoverable error Self Printing English Loading the Roll Paper Push down both sides of the printer cover to close Adjusting the Near-end Sensor Paper thick Adjustment value according to the paper you are usingRemoving Paper Jam Preventing Paper JamsPeriodical Cleaning Cleaning the Thermal HeadCleaning the Paper Holder Page Table DES Matieres Modèle standard Identification des pièces et nomenclatureModèle mural/avec socle Montage du modèle mural Emplacement de l’imprimanteMise en place du support mural Caractéristiques du support muralRepère la position des trous de forage Pour les vis Forer des trous aux endroits indiquésMur en bois Mur en béton Ø18±1 mm Ø12±1 mm Consommables et adaptateur secteurCC24±5%, 2,0 a charge de 10 sec à 5,0 a max Passez l’attache dans le tore de fer- rite Câbles de connexion et adaptateur secteurConnexion du câble d’interface Raccordement d’un appareil périphérique Connexion de l’adaptateur secteur optionnel Mise sous tension de l’imprimante Erreurs Panneau de commandeErreur récupérable automatiquement Erreur récupérableErreur de détection de papier Erreur non récupérableAuto-impression Français Chargement du rouleau de papier Ne pas toucher la lame du coupe-ruban Réglage du capteur de fin de rouleau Valeur de réglage correspondant au papier utilisé Correction de bourrages de papier Prévention des bourrages de papierNettoyage Nettoyage de la tête d’impressionNettoyage du support de papier Page Inhaltsverzeichnis Standard-Modell Beschreibung und Bezeichnung der GeräteteileWandanbringungs-/Standmodell Anbringungsteile für Wandanbringungsmodell Wahl eines Aufstellungsorts für den DruckerAnbringen des Bügels für Wandanbringungsmodell Spezifikationen des WandhaltebügelsAn den gekennzeichneten Stellen Lö Cher bohren BefestigenHolzstrukturwand Betonstrukturwand Papierdicke Kern außen Verbrauchsteile und NetzteilWichtig Anschlußkabel und Netzteil Anschließen des Schnittstellenkabels Anschluß an ein Peripheriegerät Anschließen des optionalen Netzteils Einschalten Fehler BedienfeldAutomatisch behebbare Fehler Behebbare FehlerNicht behebbare Fehler Testdruck SelbstdruckDeutsch Worden sein Einlegen der PapierrolleNicht die Schneidwerkklinge berühren Einstellung des Endanäherungs-Sensors Einstellwerte entsprechend des verwendeten Papiers Beheben von Papierstau Verhindern von PapierstauRegelmäßige Reinigung Reinigen des ThermalkopfesReinigen des Papierhalters Page Indice Modello standard Identificazione delle parti e nomenclaturaModello con supporto/da montare a parete Materiale di montaggio per il modello da montare a parete Scelta di un luogo per la stampanteMontaggo della staffa per il modello da montare a parete Specifiche della staffa di montaggio a pareteParete a struttura in legno Parete a struttura in cemento Spessore carta Nucleo esterno Diametro interno/esterno nucleoImportante Cavi di collegamento e trasformatore CA Collegamento del cavo interfaccia Collegamento ad un’unità periferica Collegamento del trasformatore CA opzionale Accensione Errori Pannello di controlloNota Errori senza recupero Stampa automatica Necessario spegnere completamente la stampante Inserimento del rotolo di carta Importante Regolazione del sensore di esaurimento prossimo Valore di regolazione secondo la carta usata Eliminazione degli inceppamenti della carta Prevenzione degli inceppamenti della cartaPulizia periodica Pulizia della testina termicaPulizia del comparto carta Page General Specifications Appendix a SpecificationsOverall dimension Standard model 180 W × 213 D × 148 H mm Paper width 111.5 ± 0.5 mmWall Mount Model Auto Cutter Specifications Electrical CharacteristicsInterface Reliability Environmental RequirementsRemarks Black mark specificationsAppendix B Dip Switch Setting Parallel Interface Type Star Page modeFactory settings of DIP switch are all on DP8340 modeCharacter Table International Character SetSerial Interface Type 105 106 Table of Connection Signals for Each Mode Parallel interface connector printer sideAppendix C Parallel Interface Appendix D Serial Interface RS-232C ConnectorFollowings are a recommended interface cable connections Cable ConnectionsModular plug Peripheral Drive ConnectorAppendix F Memory Switch Settings Overseas Subsidiary Companies Star Micronics AMERICA, INC