Star Micronics TSP800 user manual 106

Page 109

The following is the procedure for changing the settings on DIP switch No. 3.

1.Turn off the printer and all components connected to it.

2.Remove the 2 screws.

3.Remove the serial interface board unit.

4.Change the setting of the DIP switches.

5.Replace the serial interface board unit. Then secure it with the screws.

6.Turn on the printer and all components connected to it.

DIP switch 3

ON

OFF No. 1 2 3 4 5 6 7 8

DIP-SW3

The factory settings of DIP switch are all on, except for switches 7 and 8.

DIP-SW 3

Switch		Function			ON			OFF

3-1		Baud Rate					See table below

3-2
3-2

3-3		Data Length			8 bits			7 bits

3-4		Parity Check			Disabled			Enabled

3-5		Parity			Odd			Even

3-6		Handshake			DTR			XON/XOFF

3-7	Should not be changed (Should be set to off)				—			—

3-8
3-8


	Baud Rate		Switch 3-1					Switch 3-2

	4800BPS		OFF					ON

	9600BPS		ON					ON

	19200BPS		ON					OFF

APPENDIX

– 106 –

Image 109

Contents TSP800 Series EC Council Directive 89/336/EEC of 3 May Table of Contents Standard Model Parts Identification and NomenclatureWall Mount/Stand Model Mounting hardware for wall mount model Choosing a place for the printerMounting the bracket for the wall mount model Specifications of the wall mounting bracketEspecially in front of the printer Wood structure wall Concrete structure wall Nippon Paper Industries Paper thickness Core outerDC24±5%, 2.0 a 5.0 a Load 10 sec. Max Connecting Cables and AC Adapter Connecting the Interface Cable Connecting to a Peripheral Unit Connecting the Optional AC Adapter Turning Power On Control Panel ErrorsNon recoverable error Self Printing English Loading the Roll Paper Push down both sides of the printer cover to close Adjusting the Near-end Sensor Paper thick Adjustment value according to the paper you are usingRemoving Paper Jam Preventing Paper JamsCleaning the Thermal Head Periodical CleaningCleaning the Paper Holder Page Table DES Matieres Modèle standard Identification des pièces et nomenclatureModèle mural/avec socle Montage du modèle mural Emplacement de l’imprimanteMise en place du support mural Caractéristiques du support muralRepère la position des trous de forage Pour les vis Forer des trous aux endroits indiquésMur en bois Mur en béton Ø18±1 mm Ø12±1 mm Consommables et adaptateur secteurCC24±5%, 2,0 a charge de 10 sec à 5,0 a max Passez l’attache dans le tore de fer- rite Câbles de connexion et adaptateur secteurConnexion du câble d’interface Raccordement d’un appareil périphérique Connexion de l’adaptateur secteur optionnel Mise sous tension de l’imprimante Erreurs Panneau de commandeErreur récupérable automatiquement Erreur récupérableErreur de détection de papier Erreur non récupérableAuto-impression Français Chargement du rouleau de papier Ne pas toucher la lame du coupe-ruban Réglage du capteur de fin de rouleau Valeur de réglage correspondant au papier utilisé Correction de bourrages de papier Prévention des bourrages de papierNettoyage de la tête d’impression NettoyageNettoyage du support de papier Page Inhaltsverzeichnis Standard-Modell Beschreibung und Bezeichnung der GeräteteileWandanbringungs-/Standmodell Anbringungsteile für Wandanbringungsmodell Wahl eines Aufstellungsorts für den DruckerAnbringen des Bügels für Wandanbringungsmodell Spezifikationen des WandhaltebügelsAn den gekennzeichneten Stellen Lö Cher bohren BefestigenHolzstrukturwand Betonstrukturwand Papierdicke Kern außen Verbrauchsteile und NetzteilWichtig Anschlußkabel und Netzteil Anschließen des Schnittstellenkabels Anschluß an ein Peripheriegerät Anschließen des optionalen Netzteils Einschalten Fehler BedienfeldAutomatisch behebbare Fehler Behebbare FehlerNicht behebbare Fehler Testdruck SelbstdruckDeutsch Worden sein Einlegen der PapierrolleNicht die Schneidwerkklinge berühren Einstellung des Endanäherungs-Sensors Einstellwerte entsprechend des verwendeten Papiers Beheben von Papierstau Verhindern von PapierstauReinigen des Thermalkopfes Regelmäßige ReinigungReinigen des Papierhalters Page Indice Modello standard Identificazione delle parti e nomenclaturaModello con supporto/da montare a parete Materiale di montaggio per il modello da montare a parete Scelta di un luogo per la stampanteMontaggo della staffa per il modello da montare a parete Specifiche della staffa di montaggio a pareteParete a struttura in legno Parete a struttura in cemento Spessore carta Nucleo esterno Diametro interno/esterno nucleoImportante Cavi di collegamento e trasformatore CA Collegamento del cavo interfaccia Collegamento ad un’unità periferica Collegamento del trasformatore CA opzionale Accensione Pannello di controllo ErroriNota Errori senza recupero Stampa automatica Necessario spegnere completamente la stampante Inserimento del rotolo di carta Importante Regolazione del sensore di esaurimento prossimo Valore di regolazione secondo la carta usata Eliminazione degli inceppamenti della carta Prevenzione degli inceppamenti della cartaPulizia della testina termica Pulizia periodicaPulizia del comparto carta Page General Specifications Appendix a SpecificationsOverall dimension Standard model 180 W × 213 D × 148 H mm Paper width 111.5 ± 0.5 mmWall Mount Model Electrical Characteristics Auto Cutter SpecificationsInterface Reliability Environmental RequirementsRemarks Black mark specificationsAppendix B Dip Switch Setting Parallel Interface Type Star Page modeFactory settings of DIP switch are all on DP8340 modeCharacter Table International Character SetSerial Interface Type 105 106 Parallel interface connector printer side Table of Connection Signals for Each ModeAppendix C Parallel Interface Appendix D Serial Interface RS-232C ConnectorFollowings are a recommended interface cable connections Cable ConnectionsModular plug Peripheral Drive ConnectorAppendix F Memory Switch Settings Overseas Subsidiary Companies Star Micronics AMERICA, INC