Star Micronics TSP800 user manual English

Page 19

(2) Hexadecimal Dump Mode

Open the printer cover, then turn the power on while holding the FEED button. When the cover is closed, “*** HEX DUMP PRINTING ***” is printed, and the printer enters the Hexadecimal Dump Mode.

Each of the signals sent from the computer to the printer will be printed out in hexadecimal code.

This function allows you to check if a control code sent to the printer by the program being used is correct or not. The final line is not printed if its data is less than one full line. However, if the FEED button is pushed, the final line is printed. To turn off the mode, it is necessary to turn off the printer completely.

ENGLISH

– 16 –

Image 19

Contents TSP800 Series EC Council Directive 89/336/EEC of 3 May Table of Contents Standard Model Parts Identification and NomenclatureWall Mount/Stand Model Mounting hardware for wall mount model Choosing a place for the printerMounting the bracket for the wall mount model Specifications of the wall mounting bracketEspecially in front of the printer Wood structure wall Concrete structure wall Nippon Paper Industries Paper thickness Core outerDC24±5%, 2.0 a 5.0 a Load 10 sec. Max Connecting Cables and AC Adapter Connecting the Interface Cable Connecting to a Peripheral Unit Connecting the Optional AC Adapter Turning Power On Control Panel ErrorsNon recoverable error Self Printing English Loading the Roll Paper Push down both sides of the printer cover to close Adjusting the Near-end Sensor Paper thick Adjustment value according to the paper you are usingRemoving Paper Jam Preventing Paper JamsCleaning the Thermal Head Periodical CleaningCleaning the Paper Holder Page Table DES Matieres Modèle standard Identification des pièces et nomenclatureModèle mural/avec socle Montage du modèle mural Emplacement de l’imprimantePour les vis Forer des trous aux endroits indiqués Caractéristiques du support muralMise en place du support mural Repère la position des trous de forageMur en bois Mur en béton Ø18±1 mm Ø12±1 mm Consommables et adaptateur secteurCC24±5%, 2,0 a charge de 10 sec à 5,0 a max Passez l’attache dans le tore de fer- rite Câbles de connexion et adaptateur secteurConnexion du câble d’interface Raccordement d’un appareil périphérique Connexion de l’adaptateur secteur optionnel Mise sous tension de l’imprimante Erreur récupérable Panneau de commandeErreurs Erreur récupérable automatiquementErreur de détection de papier Erreur non récupérableAuto-impression Français Chargement du rouleau de papier Ne pas toucher la lame du coupe-ruban Réglage du capteur de fin de rouleau Valeur de réglage correspondant au papier utilisé Correction de bourrages de papier Prévention des bourrages de papierNettoyage de la tête d’impression NettoyageNettoyage du support de papier Page Inhaltsverzeichnis Standard-Modell Beschreibung und Bezeichnung der GeräteteileWandanbringungs-/Standmodell Anbringungsteile für Wandanbringungsmodell Wahl eines Aufstellungsorts für den DruckerBefestigen Spezifikationen des WandhaltebügelsAnbringen des Bügels für Wandanbringungsmodell An den gekennzeichneten Stellen Lö Cher bohrenHolzstrukturwand Betonstrukturwand Papierdicke Kern außen Verbrauchsteile und NetzteilWichtig Anschlußkabel und Netzteil Anschließen des Schnittstellenkabels Anschluß an ein Peripheriegerät Anschließen des optionalen Netzteils Einschalten Behebbare Fehler BedienfeldFehler Automatisch behebbare FehlerNicht behebbare Fehler Testdruck SelbstdruckDeutsch Worden sein Einlegen der PapierrolleNicht die Schneidwerkklinge berühren Einstellung des Endanäherungs-Sensors Einstellwerte entsprechend des verwendeten Papiers Beheben von Papierstau Verhindern von PapierstauReinigen des Thermalkopfes Regelmäßige ReinigungReinigen des Papierhalters Page Indice Modello standard Identificazione delle parti e nomenclaturaModello con supporto/da montare a parete Materiale di montaggio per il modello da montare a parete Scelta di un luogo per la stampanteMontaggo della staffa per il modello da montare a parete Specifiche della staffa di montaggio a pareteParete a struttura in legno Parete a struttura in cemento Spessore carta Nucleo esterno Diametro interno/esterno nucleoImportante Cavi di collegamento e trasformatore CA Collegamento del cavo interfaccia Collegamento ad un’unità periferica Collegamento del trasformatore CA opzionale Accensione Pannello di controllo ErroriNota Errori senza recupero Stampa automatica Necessario spegnere completamente la stampante Inserimento del rotolo di carta Importante Regolazione del sensore di esaurimento prossimo Valore di regolazione secondo la carta usata Eliminazione degli inceppamenti della carta Prevenzione degli inceppamenti della cartaPulizia della testina termica Pulizia periodicaPulizia del comparto carta Page Paper width 111.5 ± 0.5 mm Appendix a SpecificationsGeneral Specifications Overall dimension Standard model 180 W × 213 D × 148 H mmWall Mount Model Electrical Characteristics Auto Cutter SpecificationsInterface Reliability Environmental RequirementsRemarks Black mark specificationsAppendix B Dip Switch Setting Parallel Interface Type Star Page modeInternational Character Set DP8340 modeFactory settings of DIP switch are all on Character TableSerial Interface Type 105 106 Parallel interface connector printer side Table of Connection Signals for Each ModeAppendix C Parallel Interface Appendix D Serial Interface RS-232C ConnectorFollowings are a recommended interface cable connections Cable ConnectionsModular plug Peripheral Drive ConnectorAppendix F Memory Switch Settings Overseas Subsidiary Companies Star Micronics AMERICA, INC