Xantrex Technology ACCB-L-L1 Conventions Used, Abbreviations and Acronyms, Related Information

Page 6

About This Guide

Conventions Used

The following conventions are used in this guide.

WARNING

Warnings identify conditions that could result in personal injury or loss of life.

CAUTION

Cautions identify conditions or practices that could result in damage to the unit or other equipment.

Important: These notes describe things which are important for you to know, but not as serious as a caution or warning.

Abbreviations and Acronyms

AC

Alternating Current

ACCB-L

AC Conduit Box Long (with ground bar only)

ACCB-L-L1

AC Conduit Box Long (adds internal components for wiring)

ACCB-L-L2

AC Conduit Box Long (built on ACCB-L-L1 for dual configuration)

ACCB-L2-PCK

AC Bypass Switch Assembly only (includes wiring)

ALM

Auxiliary Load Module

AHJ

Authority Having Jurisdiction

ASC

Authorized Service Center

AWG

American Wire Gauge

CEC

Canadian Electrical Code

CSA

Canadian Standards Association

DC

Direct Current

EPO

Emergency Power Off

GSM

Generator Start Module

ICA

Inverter Communications Adapter

ICM

Inverter Control Module

ISC-S

Inverter Stacking Control – Series

NEC

National Electrical Code

RMA

Return Material Authorization

UL

Underwriters Laboratory

Related Information

You can find more information about Xantrex Technology Inc. as well as its products and services at www.xantrex.com.

iv

973-0031-01-01 Rev A

Image 6
Contents Sine Wave Plus Long AC Conduit Box Owner’s Guide Page Sine Wave Plus Long AC Conduit Box Date and Revision Audience PurposeScope OrganizationConventions Used Abbreviations and AcronymsRelated Information Important Safety Instructions Explosive gas precautions CertificationsContents Operation Figures Page Tables Xii Introduction Introduction 1The Sine Wave Plus ACCB-L BasicACCB-L-L1 Specifications ACCB-L ACCB-L-L13ACCB-L Dimensions not to scale AC Bypass Switch Assembly For more information see , Operation in this guideBlockoff Plates 5Blockoff PlatesPage Installation Preparing for the Installation Installation Tools and MaterialsCode Compliance Configuration Planning Off-Grid ConfigurationsOn-Grid Configurations Pre-Installation Service PlanningLocation Ventilation Requirements 12 305 mm Required Shock Hazard Warning Label3Cover Removal and Replacement Removing and Replacing the CoverInstalling or Removing the Blockoff Plates 4The Blockoff Plate on the Long AC Conduit BoxKnockout Preparation 5SW Plus Inverter, AC Side Showing Knockout Location6Knockouts Locations Installing Additional Breakers 7Installing Additional Breakers on the DIN RailMounting Mounting on the Xantrex Back Plate XBP9Installing the ACCB-L on the Backplate Mounting on Plywood To mount the Long AC Conduit Box on plywoodWiring General Wire Sizes and Disconnect Requirements 1Torque Values for Wiring11ACCB-L Approved Internal Components 12ACCB-L-L1 Internal Components Factory installed Installation Wiring for Off-Grid Applications Single Inverter Configurations 120 VacInstallation Step-down Configurations 240 Vac to 120 Vac Installation Step-up Configuration Deep Well Pump 120 Vac to 240 Vac Dual Inverter Configurations 120 Vac and 240 Vac Wiring for On-Grid Applications 20Wiring an On-grid Application Using a Single InverterInstallation Step-up Configurations Utility Backup 120 Vac to 240 Vac Dual Inverter Configurations 120 Vac and 240 Vac Additional Accessory Wiring 24Accessory Wiring for Single-Inverter Configurations25Accessory Wiring for Dual-Inverter Configurations Operation AC Bypass Switch Operating the AC Bypass SwitchNormal Operation Bypass OperationDual Inverters 240 Vac Loads AC Input/Output OffWarranty and Return Information WarrantyDisclaimer ProductExclusions Return Material Authorization Policy Return ProcedureOut of Warranty Service Information About Your System Serial Number Purchased From Purchase DateIndex IX-2 Rev a Page Xantrex Technology Inc