Fujitsu RX200 manual Main Memory, Installation rules

Page 25

5 Main Memory

VCAUTION!

Please observe the safety information in the chapter “Safety Instructions” on page 9ff.

The eight slots for the main memory are suitable for PC2-3200 DDR-II DIMM memory modules. The board supports a maximum of 13-16 Gbytes of main memory (depending on the configuration). Organization in four memory banks, 0 to 3, enables fast memory access with two-way interleaving.

5.1Installation rules

VCAUTION!

Memory modules have to be installed in pairs. Each memory bank must always be fully equipped with the same type of modules.

The following memory configurations are permitted:

Mem. module

1

2

3

4

5

6

7

8

Mounted

Bank/DIMM no.

1.1

1.2

1.2

1.2

1.2

1.2

1.2

1.2

memory

Socket label

DIMM

DIMM

DIMM

DIMM

DIMM

DIMM

DIMM

DIMM

banks

 

A1

B1

A2

B2

A3

B3

A4

B4

￿

 

 

 

 

 

 

 

 

 

 

 

 

Populated with 2

X

X

 

 

 

 

 

 

1

DIMMs

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Populated with 4

X

X

X

X

 

 

 

 

2

DIMMs

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Populated with 6

X

X

X

X

X

X

 

 

3

DIMMs

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Populated with 8

X

X

X

X

X

X

X

X

4

DIMMs

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OptionsGuide

17

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Primergy RX200 S2 Serversystem Certified documentation according to DIN EN ISO Comments… Suggestions… Corrections…Page Page Abbreviations Related publications Index Page Contents Page Overview of the documentation PrefaceConcept and target groups Additional documentation about the serverFurther sources of information Overview of the documentation PrefaceExtensions and conversions Additional accessible drivesSecond processor Extension of the main memoryRemoteView RemoteView Service Board S2 LPNotational conventions Page Procedure Page Before setting up Safety InstructionsInstallation and operation Page Batteries ESD label Modules with electrostatic-sensitive devicesPage Opening the server PreparationRemoving the cover Opening the serverMain Memory Installation rulesUpgrading / exchanging main memory Upgrading / exchanging main memoryProcessors Installing a second processorRemoving the ventilation duct Installing a second processorProcessors Installing the processorRemoving the heat sink dummy Vcaution Installing the ventilation duct Installing the heat sinkExchanging the processor Exchanging the processorExchanging the processor Exchanging the processor Exchanging the heat sink Page Accessible Drives Installing the LocalView Module Installing the LocalView ModuleConnecting the LocalView module Accessible DrivesInstalling a CD-ROM/DVD drive Installing a CD-ROM/DVD driveRemoving the dummy cover Installing a CD-ROM/DVD drive Installing the CD-ROM/DVD drive Installing a floppy disk drive Removing/installing a floppy disk drive Installing a floppy disk driveConnecting the data cable Page Controllers in Non-Hot-Plug PCI Slots Installing controllers Installing controllersInstalling a PCI board Removing the riser card holderMounting the board Reinstalling the riser card holderPage RemoteView Components Installing the RemoteView Service Board S2 LPRemove the slot cover Closing the server CompletionClosing the server Installing the serverAbbreviations Abbreviations GAM LVD Rtds Page Related publications Integrated Mirroring User’s Guide Index Upgrade Comments Suggestions Corrections Page Comments Suggestions Corrections
Top Page Image Contents