Cisco Systems ME3600X24CXM manual Entering the Initial Configuration Information, IP Settings

Page 78

Appendix C Configuring the Switch with the CLI-Based Setup Program

Entering the Initial Configuration Information

To power on the switch, connect one end of the AC power cord to the AC power connector on the switch, and connect the other end of the power cord to an AC power outlet.

To power on a DC switch, see Chapter 3, “Installing and Removing AC and DC Input Power Supply and Fan Modules.”

Entering the Initial Configuration Information

To set up the switch, you need to complete the setup program, which runs automatically after the switch is powered up. You must assign an IP address and other configuration information necessary for the switch to communicate with the local routers and the Internet.

IP Settings

You will need this information from your network administrator before you complete the setup program:

Switch IP address

Subnet mask (IP netmask)

Default gateway (router)

Enable secret password

Enable password

Telnet password

Completing the Setup Program

Follow these steps to complete the setup program and to create an initial configuration for the switch:

Step 1 Enter Yes at these two prompts.

Would you like to enter the initial configuration dialog? [yes/no]: yes

At any point you may enter a question mark '?' for help.

Use ctrl-c to abort configuration dialog at any prompt.

Default settings are in square brackets '[]'.

Basic management setup configures only enough connectivity for management of the system, extended setup will ask you to configure each interface on the system.

Would you like to enter basic management setup? [yes/no]: yes

Step 2 Enter a host name for the switch, and press Return.

On a command switch, the host name is limited to 28 characters; on a member switch to 31 characters. Do not use -n, where n is a number, as the last character in a host name for any switch.

Enter host name [Switch]: host_name

Cisco ME 3800X and ME 3600X Switch Hardware Installation Guide

 

C-2

OL-22168-01

 

 

 

Image 78
Contents Americas Headquarters Text Part Number OL-22168-01Page Audience PurposeRelated Publications Obtaining Documentation and Submitting a Service Request OL-22168-01 Setting Up the Switch Switch ModelsSwitch Model Description Front PanelAlarm Input Port Bits PortManagement and Console Port 10/100/1000 Gigabit Ethernet PortsSFP+ and SFP Modules Part Number Description Dwdm CAB-SFP-50CMSD Memory Slot LEDsSFP Module Patch Cable Switch LED Panels System LED DescriptionColor System Status Power Supply Module Input LED Description Power Supply and Fan LED DescriptionEthernet Management Port LED Description Alarm LEDs Description Sync LED DescriptionSD Card LED Description Rear Panel Port LEDs DescriptionLED Color Meaning Power Supply Module Features Power Supply Module LEDsFan Module Management Options Fan Module LEDNetwork Configurations Switch Installation Switch Installation 122F 50C Statement Installation Guidelines Verifying Switch OperationInstalling the Switch Powering Off the SwitchRack-Mounting Attaching Brackets to the Switch Rack-Mounting BracketsAttaching Brackets for 19-Inch Racks Attaching Brackets for 23-Inch Racks Attaching Brackets for Etsi Racks Attaching Angle Brackets for 23-Inch Racks Mounting the Switch Mounting in a RackMounting the Switch Using 23-Inch Angle Brackets Wall-Mounting Attaching Brackets for Wall-MountingMounting the Switch on a Wall Mounting Cisco ME 3800X on a WallInstalling and Removing SFP+ and SFP Modules Installing SFP+ and SFP ModulesTable- or Shelf-Mounting 11 Installing an SFP+ Module into an SFP+ Module Slot Removing SFP+ or SFP ModulesInserting and Removing the SFP+ Module Patch Cable 12 Removing a Bale-Clasp Latch SFP+ Module14 Connecting Two Switches with an SFP+ Module Patch Cable Connecting to the 10/100/1000 Ports 15 Connecting to an Ethernet PortConnecting to Fiber-Optic SFP+ and SFP Modules Where to Go NextPower Supply Module Description Model number DescriptionAC Input Power Supply Module Handle Side Connector-Side Description Fan Module DescriptionPower Supply and Fan Module Installation Installation GuidelinesEquipment That You Supply Installing an AC Power Supply Module AC-1 PSU-1 AC-2 PSU-2Removing AC Power Supply Modules AC Power Supply Module and Power-Cord Retainer in a SwitchInstalling a DC Power Supply Module Preparing for InstallationGrounding the Switch Stripping the Ground WireCrimping the Ground Lug Installing the DC Power Supply Module in the Switch Wiring the DC Input Power Source24VDC 30A Inch 8.9 mm ± 0.02 inch 0.5 mm 3 Wire lead Insulation Removing the DC Power Supply Module Installing a Fan Module 14 Inserting a Fan Module in a SwitchOL-22168-01 Diagnosing Problems Switch Post ResultsBad or Damaged Cable Switch LEDsSwitch Connections Ethernet and Fiber CablesPing the End Device SFP+ and SFP Module Port IssuesPort and Interface Settings Spanning Tree LoopsSpeed, Duplex, and Autonegotiation Clearing the Switch IP Address and ConfigurationSwitch Performance Autonegotiation and NICsFinding the Switch Serial Number Serial Number Location on the Cisco ME 3800X and MEOL-22168-01 Technical Specifications Environmental RangesPhysical Dimensions AC Power RequirementsDC Power Requirements Table A-3 Technical Specifications-ME-3600X-24FS-M Table A-4 Technical Specifications-ME-3600X-24TS-M Physical Specifications Power SpecificationsOL-22168-01 Connector Specifications 10/100/1000SFP and SFP+ Module Connectors Copper SFP Module RJ-45 Connector10/100/1000 Ethernet Management Port Figure B-5 SFP Module Patch CablePin Signal Direction Description TX TIPCables and Adapters SFP and SFP+ Module CablingCore Modal Wavelength Dwdm Cable Pinouts TP3Console Port Adapter Pinouts Figure B-11Switch Console RJ-45-to-DB-25 Port DTE DSR DTR CTS RTSOL-22168-01 Accessing the CLI Through the Console Port Starting the Terminal-Emulation SoftwareEntering the Initial Configuration Information IP SettingsCompleting the Setup Program Enter an enable password, and press Return These choices appear