Cisco Systems ME3600X24CXM Physical Dimensions, AC Power Requirements, DC Power Requirements

Page 62

Appendix A Technical Specifications

Environmental and Technical Specifications for the Switch

4.Acoustic noise is measured per ISO 7779 and declared per ISO 9296.

5.This can be limited by specification of optical modules.

Table A-2

Technical Specifications—ME-3800X-24FS-M

 

 

Physical Dimensions

 

 

 

Weight

14.50 lb (6.58 kg) (no FRU installed)

 

 

Dimensions (H x W x D)

1.72 x 17.50 x 20.39 in. (4.37 x 44.45 x 51.79 cm)

 

 

AC Power Requirements

 

 

 

Input voltage

100 to 240 VAC ± 10% (autoranging), 50 to 60 Hz.

 

 

Power consumption with 1 AC power

Total: 779 BTUs per hour (maximum).

supply module and 1 fan module

Maximum: 228 W (worst-case SFPs, SFP+ LRM, 100% traffic).

installed

Typical: 155 W (12 SFPs with 1000BASE-SX, 2 SFP+ with SR, 100% traffic).

 

 

Minimum: 123 W (no cables or SFP modules installed).

 

Power rating: 120 V (0.254 KVA), 230 V (0.248 KVA).

 

 

Power consumption with 2 AC power

Total: 796 BTUs per hour (maximum).

supply modules installed

Maximum: 233 W (worst-case SFPs, SFP+ LRM, 100% traffic).

 

 

Typical: 163 W (12 SFPs with 1000BASE-SX, 2 SFP+ with SR, 100% traffic).

 

Minimum: 132 W (no cables or SFP modules installed).

 

Power rating: 120 V (0.259 KVA), 230 V (0.254 KVA).

 

 

DC Power Requirements

 

 

 

Input voltage

18 to 32 VDC and 36 to 72 VDC.

 

 

Power consumption with 1 DC power

Total: 840 BTUs per hour (maximum).

supply module and 1 fan module

Maximum: 246 W (18 VDC input, worst-case SFPs, SFP+ LRM, 100% traffic).

installed

Typical: 156 W (48 VDC, 12 SFPs with 1000BASE-SX, 2 SFP+ with SR, 100%

 

 

traffic).

 

Minimum: 124 W (48 VDC, no cables or SFP modules installed).

 

 

Power consumption with 2 DC power

Total: 813 BTUs per hour (maximum).

supply modules installed

Maximum: 238 W (18 VDC input, worst-case SFPs, SFP+ LRM, 100% traffic).

 

 

Typical: 161 W (48 VDC, 12 SFPs with 1000BASE-SX, 2 SFP+ with SR, 100%

 

traffic).

 

Minimum: 129 W (48 VDC, no cables or SFP modules installed).

 

 

Note If you install one AC and one DC power supply module in a switch, the power specifications are similar to two installed DC power supply modules.

Cisco ME 3800X and ME 3600X Switch Hardware Installation Guide

 

A-2

OL-22168-01

 

 

 

Image 62
Contents Americas Headquarters Text Part Number OL-22168-01Page Audience PurposeRelated Publications Obtaining Documentation and Submitting a Service Request OL-22168-01 Setting Up the Switch Switch ModelsSwitch Model Description Front PanelAlarm Input Port Bits PortSFP+ and SFP Modules Management and Console Port10/100/1000 Gigabit Ethernet Ports Part Number Description Dwdm CAB-SFP-50CMSFP Module Patch Cable SD Memory SlotLEDs Color System Status Switch LED PanelsSystem LED Description Ethernet Management Port LED Description Power Supply Module Input LED DescriptionPower Supply and Fan LED Description SD Card LED Description Alarm LEDs DescriptionSync LED Description LED Color Meaning Rear PanelPort LEDs Description Power Supply Module Features Power Supply Module LEDsFan Module Management Options Fan Module LEDNetwork Configurations Switch Installation Switch Installation 122F 50C Statement Installation Guidelines Verifying Switch OperationRack-Mounting Installing the SwitchPowering Off the Switch Attaching Brackets to the Switch Rack-Mounting BracketsAttaching Brackets for 19-Inch Racks Attaching Brackets for 23-Inch Racks Attaching Brackets for Etsi Racks Attaching Angle Brackets for 23-Inch Racks Mounting the Switch Mounting in a RackMounting the Switch Using 23-Inch Angle Brackets Wall-Mounting Attaching Brackets for Wall-MountingMounting the Switch on a Wall Mounting Cisco ME 3800X on a WallTable- or Shelf-Mounting Installing and Removing SFP+ and SFP ModulesInstalling SFP+ and SFP Modules 11 Installing an SFP+ Module into an SFP+ Module Slot Removing SFP+ or SFP ModulesInserting and Removing the SFP+ Module Patch Cable 12 Removing a Bale-Clasp Latch SFP+ Module14 Connecting Two Switches with an SFP+ Module Patch Cable Connecting to the 10/100/1000 Ports 15 Connecting to an Ethernet PortConnecting to Fiber-Optic SFP+ and SFP Modules Where to Go NextPower Supply Module Description Model number DescriptionAC Input Power Supply Module Handle Side Connector-Side Description Fan Module DescriptionEquipment That You Supply Power Supply and Fan Module InstallationInstallation Guidelines Installing an AC Power Supply Module AC-1 PSU-1 AC-2 PSU-2Removing AC Power Supply Modules AC Power Supply Module and Power-Cord Retainer in a SwitchInstalling a DC Power Supply Module Preparing for InstallationGrounding the Switch Stripping the Ground WireCrimping the Ground Lug 24VDC 30A Installing the DC Power Supply Module in the SwitchWiring the DC Input Power Source Inch 8.9 mm ± 0.02 inch 0.5 mm 3 Wire lead Insulation Removing the DC Power Supply Module Installing a Fan Module 14 Inserting a Fan Module in a SwitchOL-22168-01 Diagnosing Problems Switch Post ResultsBad or Damaged Cable Switch LEDsSwitch Connections Ethernet and Fiber CablesPing the End Device SFP+ and SFP Module Port IssuesPort and Interface Settings Spanning Tree LoopsSpeed, Duplex, and Autonegotiation Clearing the Switch IP Address and ConfigurationSwitch Performance Autonegotiation and NICsFinding the Switch Serial Number Serial Number Location on the Cisco ME 3800X and MEOL-22168-01 Technical Specifications Environmental RangesDC Power Requirements Physical DimensionsAC Power Requirements Table A-3 Technical Specifications-ME-3600X-24FS-M Table A-4 Technical Specifications-ME-3600X-24TS-M Physical Specifications Power SpecificationsOL-22168-01 Connector Specifications 10/100/1000SFP and SFP+ Module Connectors Copper SFP Module RJ-45 Connector10/100/1000 Ethernet Management Port Figure B-5 SFP Module Patch CablePin Signal Direction Description TX TIPCore Modal Wavelength Cables and AdaptersSFP and SFP+ Module Cabling Dwdm Cable Pinouts TP3Console Port Adapter Pinouts Figure B-11Switch Console RJ-45-to-DB-25 Port DTE DSR DTR CTS RTSOL-22168-01 Accessing the CLI Through the Console Port Starting the Terminal-Emulation SoftwareCompleting the Setup Program Entering the Initial Configuration InformationIP Settings Enter an enable password, and press Return These choices appear