Cisco Systems ME3600X24CXM Installing and Removing SFP+ and SFP Modules, Table- or Shelf-Mounting

Page 35

Chapter 2 Switch Installation

Installing and Removing SFP+ and SFP Modules

Table- or Shelf-Mounting

Follow these steps to install the switch on a table or a shelf:

Step 1 Place the switch on a table or a shelf near an AC power source.

Step 2 After the switch is placed on the table or shelf, you need to do these tasks to complete the installation:

Power on the switch. See the “Verifying Switch Operation” section on page 2-4.

Connect to the console port, and run the initial configuration. See the Cisco ME 3800X and ME 3600X Switch Getting Started Guide for instructions.

Connect to the front-panel ports. See the “Connecting to the 10/100/1000 Ports” section on page 2-19and the “Connecting to Fiber-Optic SFP+ and SFP Modules” section on page 2-20.

For configuration instructions about using the CLI setup program, go to Appendix C, “Configuring the Switch with the CLI-Based Setup Program.”

Note When the connectors are not being used, replace the dust covers on them for protection.

Installing and Removing SFP+ and SFP Modules

Installing SFP+ and SFP Modules

Figure 2-10shows an SFP+ module that has a bale-clasp latch.

Caution We strongly recommend that you do not install or remove fiber-optic SFP+ or SFP modules with cables attached because of the potential damage to the cables, the cable connector, or the optical interfaces in the SFP+ or SFP module. Disconnect all cables before removing or installing an SFP+ or SFP module.

Removing and installing an SFP+ or SFP module can shorten its useful life. Do not remove and insert SFP+ or SFP modules more often than is absolutely necessary.

Figure 2-10 SFP+ Module with a Bale-Clasp Latch

86575

 

 

Cisco ME 3800X and ME 3600X Switch Hardware Installation Guide

 

 

 

 

 

 

OL-22168-01

 

 

2-15

 

 

 

 

 

Image 35
Contents Text Part Number OL-22168-01 Americas HeadquartersPage Purpose AudienceRelated Publications Obtaining Documentation and Submitting a Service Request OL-22168-01 Switch Models Setting Up the SwitchFront Panel Switch Model DescriptionBits Port Alarm Input PortSFP+ and SFP Modules Management and Console Port10/100/1000 Gigabit Ethernet Ports Dwdm CAB-SFP-50CM Part Number DescriptionSFP Module Patch Cable SD Memory SlotLEDs Color System Status Switch LED PanelsSystem LED Description Ethernet Management Port LED Description Power Supply Module Input LED DescriptionPower Supply and Fan LED Description SD Card LED Description Alarm LEDs DescriptionSync LED Description LED Color Meaning Rear PanelPort LEDs Description Power Supply Module LEDs Power Supply Module FeaturesFan Module Fan Module LED Management OptionsNetwork Configurations Switch Installation Switch Installation 122F 50C Statement Verifying Switch Operation Installation GuidelinesRack-Mounting Installing the SwitchPowering Off the Switch Rack-Mounting Brackets Attaching Brackets to the SwitchAttaching Brackets for 19-Inch Racks Attaching Brackets for 23-Inch Racks Attaching Brackets for Etsi Racks Attaching Angle Brackets for 23-Inch Racks Mounting in a Rack Mounting the SwitchMounting the Switch Using 23-Inch Angle Brackets Attaching Brackets for Wall-Mounting Wall-MountingMounting Cisco ME 3800X on a Wall Mounting the Switch on a WallTable- or Shelf-Mounting Installing and Removing SFP+ and SFP ModulesInstalling SFP+ and SFP Modules Removing SFP+ or SFP Modules 11 Installing an SFP+ Module into an SFP+ Module Slot12 Removing a Bale-Clasp Latch SFP+ Module Inserting and Removing the SFP+ Module Patch Cable14 Connecting Two Switches with an SFP+ Module Patch Cable 15 Connecting to an Ethernet Port Connecting to the 10/100/1000 PortsWhere to Go Next Connecting to Fiber-Optic SFP+ and SFP ModulesModel number Description Power Supply Module DescriptionAC Input Power Supply Module Handle Side Fan Module Description Connector-Side DescriptionEquipment That You Supply Power Supply and Fan Module InstallationInstallation Guidelines AC-1 PSU-1 AC-2 PSU-2 Installing an AC Power Supply ModuleAC Power Supply Module and Power-Cord Retainer in a Switch Removing AC Power Supply ModulesPreparing for Installation Installing a DC Power Supply ModuleStripping the Ground Wire Grounding the SwitchCrimping the Ground Lug 24VDC 30A Installing the DC Power Supply Module in the SwitchWiring the DC Input Power Source Inch 8.9 mm ± 0.02 inch 0.5 mm 3 Wire lead Insulation Removing the DC Power Supply Module 14 Inserting a Fan Module in a Switch Installing a Fan ModuleOL-22168-01 Switch Post Results Diagnosing ProblemsEthernet and Fiber Cables Switch LEDsSwitch Connections Bad or Damaged CableSpanning Tree Loops SFP+ and SFP Module Port IssuesPort and Interface Settings Ping the End DeviceAutonegotiation and NICs Clearing the Switch IP Address and ConfigurationSwitch Performance Speed, Duplex, and AutonegotiationSerial Number Location on the Cisco ME 3800X and ME Finding the Switch Serial NumberOL-22168-01 Environmental Ranges Technical SpecificationsDC Power Requirements Physical DimensionsAC Power Requirements Table A-3 Technical Specifications-ME-3600X-24FS-M Table A-4 Technical Specifications-ME-3600X-24TS-M Power Specifications Physical SpecificationsOL-22168-01 10/100/1000 Connector SpecificationsCopper SFP Module RJ-45 Connector SFP and SFP+ Module ConnectorsFigure B-5 SFP Module Patch Cable 10/100/1000 Ethernet Management PortTX TIP Pin Signal Direction DescriptionCore Modal Wavelength Cables and AdaptersSFP and SFP+ Module Cabling Dwdm TP3 Cable PinoutsFigure B-11 Console Port Adapter PinoutsDSR DTR CTS RTS Switch Console RJ-45-to-DB-25 Port DTEOL-22168-01 Starting the Terminal-Emulation Software Accessing the CLI Through the Console PortCompleting the Setup Program Entering the Initial Configuration InformationIP Settings Enter an enable password, and press Return These choices appear