Cisco Systems ME3600X24CXM manual Mounting the Switch on a Wall, Mounting Cisco ME 3800X on a Wall

Page 34

Chapter 2 Switch Installation

Installing the Switch

Mounting the Switch on a Wall

For the best support of the switch and cables, make sure that the switch is attached securely to wall studs or to a firmly attached plywood mounting backboard.

Warning Read the wall-mounting instructions carefully before beginning installation. Failure to use the correct hardware or to follow the correct procedures could result in a hazardous situation to people and damage to the system. Statement 378

Mount the switch with the side panel facing up (Figure 2-9).

Figure 2-9 Mounting Cisco ME 3800X on a Wall

1

1

1User-supplied screws

			1	2
				24X
				14X
				12X
				2X
				CONSOLE
				ALARMS
ALM1	ALM2	ALM3	ALM4
PSIN1	PSIN2	PS/FAN1	PS/FAN2	SDCARD

207932

You need to do these tasks to complete the installation:

•Power on the switch. See the “Verifying Switch Operation” section on page 2-4.

•Connect to the console port, and run the initial configuration. See the Cisco ME 3800X and ME 3600X Switch Getting Started Guide for instructions.

•Connect to the front-panel ports. See the “Connecting to the 10/100/1000 Ports” section on page 2-19and the “Connecting to Fiber-Optic SFP+ and SFP Modules” section on page 2-20.

For configuration instructions about using the CLI setup program, go to Appendix C, “Configuring the Switch with the CLI-Based Setup Program.”

	Cisco ME 3800X and ME 3600X Switch Hardware Installation Guide
2-14	OL-22168-01

Image 34

Contents Americas Headquarters Text Part Number OL-22168-01Page Audience PurposeRelated Publications Obtaining Documentation and Submitting a Service Request OL-22168-01 Setting Up the Switch Switch ModelsSwitch Model Description Front PanelAlarm Input Port Bits Port10/100/1000 Gigabit Ethernet Ports Management and Console PortSFP+ and SFP Modules Part Number Description Dwdm CAB-SFP-50CMLEDs SD Memory SlotSFP Module Patch Cable System LED Description Switch LED PanelsColor System Status Power Supply and Fan LED Description Power Supply Module Input LED DescriptionEthernet Management Port LED Description Sync LED Description Alarm LEDs DescriptionSD Card LED Description Port LEDs Description Rear PanelLED Color Meaning Power Supply Module Features Power Supply Module LEDsFan Module Management Options Fan Module LEDNetwork Configurations Switch Installation Switch Installation 122F 50C Statement Installation Guidelines Verifying Switch OperationPowering Off the Switch Installing the SwitchRack-Mounting Attaching Brackets to the Switch Rack-Mounting BracketsAttaching Brackets for 19-Inch Racks Attaching Brackets for 23-Inch Racks Attaching Brackets for Etsi Racks Attaching Angle Brackets for 23-Inch Racks Mounting the Switch Mounting in a RackMounting the Switch Using 23-Inch Angle Brackets Wall-Mounting Attaching Brackets for Wall-MountingMounting the Switch on a Wall Mounting Cisco ME 3800X on a WallInstalling SFP+ and SFP Modules Installing and Removing SFP+ and SFP ModulesTable- or Shelf-Mounting 11 Installing an SFP+ Module into an SFP+ Module Slot Removing SFP+ or SFP ModulesInserting and Removing the SFP+ Module Patch Cable 12 Removing a Bale-Clasp Latch SFP+ Module14 Connecting Two Switches with an SFP+ Module Patch Cable Connecting to the 10/100/1000 Ports 15 Connecting to an Ethernet PortConnecting to Fiber-Optic SFP+ and SFP Modules Where to Go NextPower Supply Module Description Model number DescriptionAC Input Power Supply Module Handle Side Connector-Side Description Fan Module DescriptionInstallation Guidelines Power Supply and Fan Module InstallationEquipment That You Supply Installing an AC Power Supply Module AC-1 PSU-1 AC-2 PSU-2Removing AC Power Supply Modules AC Power Supply Module and Power-Cord Retainer in a SwitchInstalling a DC Power Supply Module Preparing for InstallationGrounding the Switch Stripping the Ground WireCrimping the Ground Lug Wiring the DC Input Power Source Installing the DC Power Supply Module in the Switch24VDC 30A Inch 8.9 mm ± 0.02 inch 0.5 mm 3 Wire lead Insulation Removing the DC Power Supply Module Installing a Fan Module 14 Inserting a Fan Module in a SwitchOL-22168-01 Diagnosing Problems Switch Post ResultsBad or Damaged Cable Switch LEDsSwitch Connections Ethernet and Fiber CablesPing the End Device SFP+ and SFP Module Port IssuesPort and Interface Settings Spanning Tree LoopsSpeed, Duplex, and Autonegotiation Clearing the Switch IP Address and ConfigurationSwitch Performance Autonegotiation and NICsFinding the Switch Serial Number Serial Number Location on the Cisco ME 3800X and MEOL-22168-01 Technical Specifications Environmental RangesAC Power Requirements Physical DimensionsDC Power Requirements Table A-3 Technical Specifications-ME-3600X-24FS-M Table A-4 Technical Specifications-ME-3600X-24TS-M Physical Specifications Power SpecificationsOL-22168-01 Connector Specifications 10/100/1000SFP and SFP+ Module Connectors Copper SFP Module RJ-45 Connector10/100/1000 Ethernet Management Port Figure B-5 SFP Module Patch CablePin Signal Direction Description TX TIPSFP and SFP+ Module Cabling Cables and AdaptersCore Modal Wavelength Dwdm Cable Pinouts TP3Console Port Adapter Pinouts Figure B-11Switch Console RJ-45-to-DB-25 Port DTE DSR DTR CTS RTSOL-22168-01 Accessing the CLI Through the Console Port Starting the Terminal-Emulation SoftwareIP Settings Entering the Initial Configuration InformationCompleting the Setup Program Enter an enable password, and press Return These choices appear