Cisco Systems ME3600X24CXM manual Fan Module Description, Connector-Side Description

Page 43

Chapter 3 Installing and Removing AC and DC Input Power Supply and Fan Modules

Fan Module Description

Fan Module Description

Table 3-2 Fan Module Model Number and Description

Model number	Description

ME-FANTRAY	Fan module

The fan module provides cooling and proper airflow when only one power supply module is installed.

Caution Both slots must be occupied either by two power supply modules or a power supply and a fan module. Do not run the switch with an empty slot unless you are replacing a faulty power supply or fan module. Running the switch with an empty slot triggers an alarm.

Each fan module contains three fans. The switch can operate safely if one fan fails. A fan failure triggers an alarm. When a fan fails, replace the fan module immediately.

Figure 3-3 Fan Module Handle Side

1

2

1

2

207448

3

Fan module

3 Extraction handle

Fan module status LED

Connector-Side Description

Figure 3-4shows the connector side of the power supply and fan module, which connects to the switch rear panel through its power supply module slot.

Cisco ME 3800X and ME 3600X Switch Hardware Installation Guide

	OL-22168-01	3-3

Image 43

Contents Text Part Number OL-22168-01 Americas HeadquartersPage Purpose AudienceRelated Publications Obtaining Documentation and Submitting a Service Request OL-22168-01 Switch Models Setting Up the SwitchFront Panel Switch Model DescriptionBits Port Alarm Input Port10/100/1000 Gigabit Ethernet Ports Management and Console PortSFP+ and SFP Modules Dwdm CAB-SFP-50CM Part Number DescriptionLEDs SD Memory SlotSFP Module Patch Cable System LED Description Switch LED PanelsColor System Status Power Supply and Fan LED Description Power Supply Module Input LED DescriptionEthernet Management Port LED Description Sync LED Description Alarm LEDs DescriptionSD Card LED Description Port LEDs Description Rear PanelLED Color Meaning Power Supply Module LEDs Power Supply Module FeaturesFan Module Fan Module LED Management OptionsNetwork Configurations Switch Installation Switch Installation 122F 50C Statement Verifying Switch Operation Installation GuidelinesPowering Off the Switch Installing the SwitchRack-Mounting Rack-Mounting Brackets Attaching Brackets to the SwitchAttaching Brackets for 19-Inch Racks Attaching Brackets for 23-Inch Racks Attaching Brackets for Etsi Racks Attaching Angle Brackets for 23-Inch Racks Mounting in a Rack Mounting the SwitchMounting the Switch Using 23-Inch Angle Brackets Attaching Brackets for Wall-Mounting Wall-MountingMounting Cisco ME 3800X on a Wall Mounting the Switch on a WallInstalling SFP+ and SFP Modules Installing and Removing SFP+ and SFP ModulesTable- or Shelf-Mounting Removing SFP+ or SFP Modules 11 Installing an SFP+ Module into an SFP+ Module Slot12 Removing a Bale-Clasp Latch SFP+ Module Inserting and Removing the SFP+ Module Patch Cable14 Connecting Two Switches with an SFP+ Module Patch Cable 15 Connecting to an Ethernet Port Connecting to the 10/100/1000 PortsWhere to Go Next Connecting to Fiber-Optic SFP+ and SFP ModulesModel number Description Power Supply Module DescriptionAC Input Power Supply Module Handle Side Fan Module Description Connector-Side DescriptionInstallation Guidelines Power Supply and Fan Module InstallationEquipment That You Supply AC-1 PSU-1 AC-2 PSU-2 Installing an AC Power Supply ModuleAC Power Supply Module and Power-Cord Retainer in a Switch Removing AC Power Supply ModulesPreparing for Installation Installing a DC Power Supply ModuleStripping the Ground Wire Grounding the SwitchCrimping the Ground Lug Wiring the DC Input Power Source Installing the DC Power Supply Module in the Switch24VDC 30A Inch 8.9 mm ± 0.02 inch 0.5 mm 3 Wire lead Insulation Removing the DC Power Supply Module 14 Inserting a Fan Module in a Switch Installing a Fan ModuleOL-22168-01 Switch Post Results Diagnosing ProblemsEthernet and Fiber Cables Switch LEDsSwitch Connections Bad or Damaged CableSpanning Tree Loops SFP+ and SFP Module Port IssuesPort and Interface Settings Ping the End DeviceAutonegotiation and NICs Clearing the Switch IP Address and ConfigurationSwitch Performance Speed, Duplex, and AutonegotiationSerial Number Location on the Cisco ME 3800X and ME Finding the Switch Serial NumberOL-22168-01 Environmental Ranges Technical SpecificationsAC Power Requirements Physical DimensionsDC Power Requirements Table A-3 Technical Specifications-ME-3600X-24FS-M Table A-4 Technical Specifications-ME-3600X-24TS-M Power Specifications Physical SpecificationsOL-22168-01 10/100/1000 Connector SpecificationsCopper SFP Module RJ-45 Connector SFP and SFP+ Module ConnectorsFigure B-5 SFP Module Patch Cable 10/100/1000 Ethernet Management PortTX TIP Pin Signal Direction DescriptionSFP and SFP+ Module Cabling Cables and AdaptersCore Modal Wavelength Dwdm TP3 Cable PinoutsFigure B-11 Console Port Adapter PinoutsDSR DTR CTS RTS Switch Console RJ-45-to-DB-25 Port DTEOL-22168-01 Starting the Terminal-Emulation Software Accessing the CLI Through the Console PortIP Settings Entering the Initial Configuration InformationCompleting the Setup Program Enter an enable password, and press Return These choices appear