Cisco Systems 78-6897-01 manual Determining the Nsap Address, Step Command Purpose

Page 37

Configuring SVCs

Determining the NSAP Address

Determine the ATM network service access point (NSAP) address for both the source and destination routers. The NSAP addresses is required to complete the SVC.

Step

Command

Purpose

1

Router# show interface atm

Display the 20-byte NSAP address of the

 

port[/slot ][.subinterface ]

router port on which the SVC terminates.

 

 

Enter the address in Table3-1.

 

 

The NSAP address does not display in

 

 

certain modes. In this case, you must enter

 

 

an NSAP address that meets the following

 

 

criteria:

 

 

• It must be unique in the network.

 

 

• It must not be a broadcast or multicast

 

 

MAC address.

2

(No command.)

Repeat this procedure to display the NSAP

 

 

address of the other router.

Enter the 20-byte NSAP address of each router in the space provided below in Table3-1.

Table3-1 NSAP Addresses

Router

NSAP Address

Source router1

Destination router2

1In Figure3-1, the source router is router A.

2In Figure3-1, the destination router is router D.

3-6ATM Switch Router Quick Software Configuration Guide

Image 37
Contents Strongly agree Strongly disagree Page ATM Switch Router Quick Software Configuration Guide Page ATM Switch Router Quick Software Configuration Guide About This Guide Chapter Using the Command-Line InterfaceChapter Getting Started Chapter Configuring Lane Index Chapter Configuring Tag SwitchingViii ATMSwitch Router Quick Software Configuration Guide Audience PurposeRelated Documentation OrganizationOrganization Chapter Title DescriptionConventions ConventionsConvention Description Boldface screen fontTips Cisco Connection OnlineCisco Connection Online Documentation CD-ROM Documentation CD-ROMXiv ATMSwitch Router Quick Software Configuration Guide Using the Command-Line Interface Switch# configure terminal Understanding Command ModesGetting Help Getting HelpUnderstanding Interface Numbering Understanding Interface NumberingCard Numbering Catalyst8540MSR Shown Card NumberingSubcard Numbering Subcard NumberingPort Numbering Processor Card NumberingPort Numbering Example of Interface Numbering Example of Interface NumberingDisplaying the Configuration Undoing a Command or FeatureUndoing a Command or Feature Switch# more systemrunning-configSaving Configuration Changes Saving Configuration ChangesSwitch# copy systemrunning-config nvramstartup-config Where to Go Next Where to Go NextGetting Started Naming the ATM Switch RouterStep Command Naming the ATM Switch RouterExample VerifyAssigning a Password Assigning a PasswordSetting Up Remote Administrative Access Setting Up Remote Administrative AccessSwitch# show interface ethernet 6ATMSwitch Router Quick Software Configuration Guide Configuring SVCs Configuring SVCs, PVCs Soft PVCs, PVPs, VP TunnelsConfiguring SVCs Configuring the RouterConfiguring the Router Configuring Signaling on the RoutersRouter# configure terminal Routerconfig# Router# configure terminal Configuring the IP Address and ESI AddressSwitch# show atm vc interface atm MultipointSwitch# show interface atm Configuring the Router PurposeDetermining the Nsap Address Step Command PurposeNsap Addresses Router Router# show interface atmConfigure a Map Group and Map List Router# ping Configuring SVCs Step CommandConfiguring PVCs Configuring PVCsVci interface atm card/subcard/port.vpt# vpi vci Configuring the ATM Switch RouterSwitchconfig-if#atm pvc 2 100 interface atm 0 0 any-vci Configuring the ATM Switch RouterSwitch# show atm vc interface atm 3/0/1 12ATM Switch Router Quick Software Configuration Guide Configuring Soft PVCs Step Command Purpose Configuring Soft PVCsExample Network for Configuring Soft PVCs Configuring Soft PVCsSwitch# show atm addresses Determining the Destination ATM Switch Router Nsap AddressSwitch# show atm address Switchconfig# Configuring the Source ATM Switch RouterSwitch# show atm vc interface atm 0/0/0 Configuring Soft PVCs Step Command Configuring PVPs Configuring PVPsAtm Configuring VP Tunnels Configuring VP TunnelsVPIs and VPTs for the Example VP Tunnel Switch a Switch B Switchconfig-if#interface atm 3/0/2.99 Switchconfig# interface atm 3/0/2Atm vp Switch# show atm interface atm 3/0/2.9924ATM Switch Router Quick Software Configuration Guide Configuring Lane Understanding Lane Components Understanding Lane on ATMUnderstanding Lane on ATM Supporting LAN Protocols Implementing LaneAddressing Implementing LaneAssigning Components to Interfaces and Subinterfaces Configuring Lane Router and LAN Switch RequirementsConfiguring a LEC Configuring a LECConfiguring the ATM Address of the Lecs Configuring the LecsConfiguring the Lecs Switchconfig# atm lecs-address lecsaddressConfiguring the Lecs Database Purpose Configuring the Lecs DatabaseConfiguring the LES/BUS Step Command Configuring the LES/BUSLane Configuration Examples Lane Configuration ExamplesATMSwitch# show lane default-atm-addresses interface ATM0 ATM Switch RouterATMSwitch# configure terminal ATMSwitch# copy systemrunning-config nvramstartup-configLE BUS ATM0.1 ATMSwitch# show lane configRouter1# configure terminal ATMSwitch# show lane clientRouter1# more systemrunning-config RouterATM enable ATM# configure terminal Catalyst 5500 SwitchATMconfig-if#lane server-bus ethernet engelan ATM# copy systemrunning-config nvramstartup-configATM# show lane client ATMconfig-subif#lane client ethernet 1 engelanVerifying Connectivity Switch# show laneVerifying Connectivity ATMSwitch# ping ATMSwitch# show lane client 18ATMSwitch Router Quick Software Configuration Guide Software Restrictions Configuring Tag SwitchingEnabling Tag Switching on the ATM Interface Configuring Tag Switching on an ATM Switch RouterConfiguring Tag Switching on an ATM Switch Router Switchconfig-if#ip unnumbered loopback Enabling Tag Switching on the ATM Interface Step CommandSwitch# show tag-switching interfaces ExamplesConfiguring the Routing Protocol Switch# show ip ospf Configuring the Routing ProtocolConfiguring Tag Switching on a Router Configuring Tag Switching on a RouterRouter 5-1 Configuration Tag Switching Configuration ExampleTag Switching Configuration Example Router# show tag-switching interfaceRouter 5-3 Configuration Router 5-2 ConfigurationRouter 5-5 Configuration ATM Switch Router A5-4 ConfigurationAtmA5-4#configure terminal AtmA6-4#configure terminal ATM Switch Router A6-4 ConfigurationD E Index ATMSwitch Router Quick Software Configuration Guide Index Index ATMSwitch Router Quick Software Configuration Guide