Cisco Systems 78-6897-01 manual Setting Up Remote Administrative Access

Page 29

Setting Up Remote Administrative Access

Setting Up Remote Administrative Access

You can configure the Ethernet interface on the processor card (CPU card) so that you can Telnet to the ATM switch router and configure it remotely. This section describes how to configure the Ethernet port for remote administrative access.

Note For local administrative access, connect a PC or workstation to the console port on the processor card. This requires physical access to the ATM switch router.

Take these steps:

Step Command

1Switch> enable

2Switch# configure terminal Switch(config)#

3Switch(config)# ip route prefix mask ethernet 0[.subinterface]

4Switch(config)# interface ethernet 0 Switch(config-if)#

5Switch(config-if)# ip address address

6Switch(config)# end Switch#

Purpose

Enter privileged EXEC mode.

Enter global configuration mode.

Configure a static route on the Ethernet interface. If your management station or TFTP1 server is on a different subnet than the switch, you must configure a static IP route.2

Enter interface configuration mode on the Ethernet interface.

Configure an IP address on the Ethernet interface.

Return to privileged EXEC mode.

1TFTP = Trivial File Transfer Protocol.

2If you fail to configure a static IP route before installing a new image, you might lose remote administrative access to the switch. If this happens, you can regain access from a direct console connection, although this requires physical access to the console port on the processor card.

2-4ATMSwitch Router Quick Software Configuration Guide

Image 29
Contents Strongly agree Strongly disagree Page ATM Switch Router Quick Software Configuration Guide Page ATM Switch Router Quick Software Configuration Guide Chapter Getting Started Chapter Using the Command-Line InterfaceAbout This Guide Chapter Configuring Lane Index Chapter Configuring Tag SwitchingViii ATMSwitch Router Quick Software Configuration Guide Audience PurposeRelated Documentation OrganizationOrganization Chapter Title DescriptionConventions ConventionsConvention Description Boldface screen fontCisco Connection Online Cisco Connection OnlineTips Documentation CD-ROM Documentation CD-ROMXiv ATMSwitch Router Quick Software Configuration Guide Using the Command-Line Interface Switch# configure terminal Understanding Command ModesGetting Help Getting HelpUnderstanding Interface Numbering Understanding Interface NumberingCard Numbering Catalyst8540MSR Shown Card NumberingSubcard Numbering Subcard NumberingPort Numbering Processor Card NumberingPort Numbering Example of Interface Numbering Example of Interface NumberingDisplaying the Configuration Undoing a Command or FeatureUndoing a Command or Feature Switch# more systemrunning-configSwitch# copy systemrunning-config nvramstartup-config Saving Configuration ChangesSaving Configuration Changes Where to Go Next Where to Go NextGetting Started Naming the ATM Switch RouterStep Command Naming the ATM Switch RouterExample VerifyAssigning a Password Assigning a PasswordSetting Up Remote Administrative Access Setting Up Remote Administrative AccessSwitch# show interface ethernet 6ATMSwitch Router Quick Software Configuration Guide Configuring SVCs Configuring SVCs, PVCs Soft PVCs, PVPs, VP TunnelsConfiguring SVCs Configuring the RouterRouter# configure terminal Routerconfig# Configuring Signaling on the RoutersConfiguring the Router Router# configure terminal Configuring the IP Address and ESI AddressSwitch# show atm vc interface atm MultipointSwitch# show interface atm Configuring the Router PurposeDetermining the Nsap Address Step Command PurposeNsap Addresses Router Router# show interface atmConfigure a Map Group and Map List Router# ping Configuring SVCs Step CommandConfiguring PVCs Configuring PVCsVci interface atm card/subcard/port.vpt# vpi vci Configuring the ATM Switch RouterSwitch# show atm vc interface atm 3/0/1 Configuring the ATM Switch RouterSwitchconfig-if#atm pvc 2 100 interface atm 0 0 any-vci 12ATM Switch Router Quick Software Configuration Guide Configuring Soft PVCs Step Command Purpose Configuring Soft PVCsExample Network for Configuring Soft PVCs Configuring Soft PVCsSwitch# show atm address Determining the Destination ATM Switch Router Nsap AddressSwitch# show atm addresses Switchconfig# Configuring the Source ATM Switch RouterSwitch# show atm vc interface atm 0/0/0 Configuring Soft PVCs Step Command Configuring PVPs Configuring PVPsAtm VPIs and VPTs for the Example VP Tunnel Switch a Switch B Configuring VP TunnelsConfiguring VP Tunnels Switchconfig-if#interface atm 3/0/2.99 Switchconfig# interface atm 3/0/2Atm vp Switch# show atm interface atm 3/0/2.9924ATM Switch Router Quick Software Configuration Guide Configuring Lane Understanding Lane on ATM Understanding Lane on ATMUnderstanding Lane Components Supporting LAN Protocols Implementing LaneAddressing Implementing LaneAssigning Components to Interfaces and Subinterfaces Configuring Lane Router and LAN Switch RequirementsConfiguring a LEC Configuring a LECConfiguring the ATM Address of the Lecs Configuring the LecsConfiguring the Lecs Switchconfig# atm lecs-address lecsaddressConfiguring the Lecs Database Purpose Configuring the Lecs DatabaseConfiguring the LES/BUS Step Command Configuring the LES/BUSLane Configuration Examples Lane Configuration ExamplesATMSwitch# show lane default-atm-addresses interface ATM0 ATM Switch RouterATMSwitch# configure terminal ATMSwitch# copy systemrunning-config nvramstartup-configLE BUS ATM0.1 ATMSwitch# show lane configRouter1# configure terminal ATMSwitch# show lane clientRouter1# more systemrunning-config RouterATM enable ATM# configure terminal Catalyst 5500 SwitchATMconfig-if#lane server-bus ethernet engelan ATM# copy systemrunning-config nvramstartup-configATM# show lane client ATMconfig-subif#lane client ethernet 1 engelanVerifying Connectivity Switch# show laneVerifying Connectivity ATMSwitch# ping ATMSwitch# show lane client 18ATMSwitch Router Quick Software Configuration Guide Software Restrictions Configuring Tag SwitchingConfiguring Tag Switching on an ATM Switch Router Configuring Tag Switching on an ATM Switch RouterEnabling Tag Switching on the ATM Interface Switchconfig-if#ip unnumbered loopback Enabling Tag Switching on the ATM Interface Step CommandSwitch# show tag-switching interfaces ExamplesConfiguring the Routing Protocol Switch# show ip ospf Configuring the Routing ProtocolConfiguring Tag Switching on a Router Configuring Tag Switching on a RouterRouter 5-1 Configuration Tag Switching Configuration ExampleTag Switching Configuration Example Router# show tag-switching interfaceRouter 5-3 Configuration Router 5-2 ConfigurationAtmA5-4#configure terminal ATM Switch Router A5-4 ConfigurationRouter 5-5 Configuration AtmA6-4#configure terminal ATM Switch Router A6-4 ConfigurationD E Index ATMSwitch Router Quick Software Configuration Guide Index Index ATMSwitch Router Quick Software Configuration Guide