Cisco Systems 78-6897-01 manual Configuring the Routing Protocol, Switch# show ip ospf

Page 78

Configuring the Routing Protocol

Example

Note An IP address of 1.1.1.1 with a subnet mask of 255.255.255.0 is entered as an IP network prefix of 1.1.1.0 with a subnet mask of 0.0.0.255. Likewise, an IP address of

1.2.1.1with a subnet mask of 255.255.255.0 is entered as an IP network prefix of 1.2.1.0 with a subnet mask of 0.0.0.255.

Switch(config)# router ospf 10000 Switch(config-router)# network 1.1.1.0 0.0.0.255 area 0 Switch(config-router)# network 1.2.1.0 0.0.0.255 area 0 Switch(config-router)# network 1.3.0.0 0.0.255.255 area 0 Switch(config-router)# network 200.2.2.0 0.0.0.255 area 0 Switch(config-router)# network 1.0.1.0 0.0.0.255 area 0 Switch(config-router)# network 1.18.0.0 0.0.255.255 area 0 Switch(config-router)# exit

Switch(config)#

Verify

Switch# show ip ospf

Routing Process "ospf 10000" with ID 1.0.1.11

Supports only single TOS(TOS0) routes

SPF schedule delay 5 secs, Hold time between two SPFs 10 secs Number of DCbitless external LSA 0

Number of DoNotAge external LSA 0

Number of areas in this router is 1. 1 normal 0 stub 0 nssa Area BACKBONE(0) (Inactive)

Number of interfaces in this area is 4

Area has no authentication

SPF algorithm executed 2 times

Area ranges are

Link State Update Interval is 00:30:00 and due in 00:14:42 Link State Age Interval is 00:20:00 and due in 00:14:10 Number of DCbitless LSA 0

Number of indication LSA 0

Number of DoNotAge LSA 0

Switch#

Configuring Tag Switching 5-5

Image 78
Contents Strongly agree Strongly disagree Page ATM Switch Router Quick Software Configuration Guide Page ATM Switch Router Quick Software Configuration Guide Chapter Using the Command-Line Interface About This GuideChapter Getting Started Chapter Configuring Lane Chapter Configuring Tag Switching IndexViii ATMSwitch Router Quick Software Configuration Guide Purpose AudienceOrganization OrganizationRelated Documentation Chapter Title DescriptionConvention Description ConventionsConventions Boldface screen fontCisco Connection Online TipsCisco Connection Online Documentation CD-ROM Documentation CD-ROMXiv ATMSwitch Router Quick Software Configuration Guide Using the Command-Line Interface Getting Help Understanding Command ModesSwitch# configure terminal Getting HelpUnderstanding Interface Numbering Understanding Interface NumberingCard Numbering Card Numbering Catalyst8540MSR ShownSubcard Numbering Subcard NumberingProcessor Card Numbering Port NumberingPort Numbering Example of Interface Numbering Example of Interface NumberingUndoing a Command or Feature Undoing a Command or FeatureDisplaying the Configuration Switch# more systemrunning-configSaving Configuration Changes Saving Configuration ChangesSwitch# copy systemrunning-config nvramstartup-config Where to Go Next Where to Go NextNaming the ATM Switch Router Getting StartedExample Naming the ATM Switch RouterStep Command VerifyAssigning a Password Assigning a PasswordSetting Up Remote Administrative Access Setting Up Remote Administrative AccessSwitch# show interface ethernet 6ATMSwitch Router Quick Software Configuration Guide Configuring SVCs, PVCs Soft PVCs, PVPs, VP Tunnels Configuring SVCsConfiguring the Router Configuring SVCsConfiguring Signaling on the Routers Configuring the RouterRouter# configure terminal Routerconfig# Switch# show atm vc interface atm Configuring the IP Address and ESI AddressRouter# configure terminal MultipointConfiguring the Router Purpose Switch# show interface atmNsap Addresses Router Step Command PurposeDetermining the Nsap Address Router# show interface atmConfigure a Map Group and Map List Configuring SVCs Step Command Router# pingConfiguring PVCs Configuring PVCsConfiguring the ATM Switch Router Vci interface atm card/subcard/port.vpt# vpi vciConfiguring the ATM Switch Router Switchconfig-if#atm pvc 2 100 interface atm 0 0 any-vciSwitch# show atm vc interface atm 3/0/1 12ATM Switch Router Quick Software Configuration Guide Configuring Soft PVCs Configuring Soft PVCs Step Command PurposeConfiguring Soft PVCs Example Network for Configuring Soft PVCsDetermining the Destination ATM Switch Router Nsap Address Switch# show atm addressesSwitch# show atm address Configuring the Source ATM Switch Router Switchconfig#Switch# show atm vc interface atm 0/0/0 Configuring Soft PVCs Step Command Configuring PVPs Configuring PVPsAtm Configuring VP Tunnels Configuring VP TunnelsVPIs and VPTs for the Example VP Tunnel Switch a Switch B Switchconfig# interface atm 3/0/2 Switchconfig-if#interface atm 3/0/2.99Switch# show atm interface atm 3/0/2.99 Atm vp24ATM Switch Router Quick Software Configuration Guide Configuring Lane Understanding Lane on ATM Understanding Lane ComponentsUnderstanding Lane on ATM Addressing Implementing LaneSupporting LAN Protocols Implementing LaneConfiguring Lane Router and LAN Switch Requirements Assigning Components to Interfaces and SubinterfacesConfiguring a LEC Configuring a LECConfiguring the Lecs Configuring the LecsConfiguring the ATM Address of the Lecs Switchconfig# atm lecs-address lecsaddressConfiguring the Lecs Database Configuring the Lecs Database PurposeConfiguring the LES/BUS Configuring the LES/BUS Step CommandLane Configuration Examples Lane Configuration ExamplesATMSwitch# configure terminal ATM Switch RouterATMSwitch# show lane default-atm-addresses interface ATM0 ATMSwitch# copy systemrunning-config nvramstartup-configATMSwitch# show lane config LE BUS ATM0.1Router1# more systemrunning-config ATMSwitch# show lane clientRouter1# configure terminal RouterATMconfig-if#lane server-bus ethernet engelan Catalyst 5500 SwitchATM enable ATM# configure terminal ATM# copy systemrunning-config nvramstartup-configATMconfig-subif#lane client ethernet 1 engelan ATM# show lane clientSwitch# show lane Verifying ConnectivityVerifying Connectivity ATMSwitch# ping ATMSwitch# show lane client 18ATMSwitch Router Quick Software Configuration Guide Configuring Tag Switching Software RestrictionsConfiguring Tag Switching on an ATM Switch Router Enabling Tag Switching on the ATM InterfaceConfiguring Tag Switching on an ATM Switch Router Switch# show tag-switching interfaces Enabling Tag Switching on the ATM Interface Step CommandSwitchconfig-if#ip unnumbered loopback ExamplesConfiguring the Routing Protocol Configuring the Routing Protocol Switch# show ip ospfConfiguring Tag Switching on a Router Configuring Tag Switching on a RouterTag Switching Configuration Example Tag Switching Configuration ExampleRouter 5-1 Configuration Router# show tag-switching interfaceRouter 5-2 Configuration Router 5-3 ConfigurationATM Switch Router A5-4 Configuration Router 5-5 ConfigurationAtmA5-4#configure terminal ATM Switch Router A6-4 Configuration AtmA6-4#configure terminalD E Index ATMSwitch Router Quick Software Configuration Guide Index Index ATMSwitch Router Quick Software Configuration Guide