Cisco Systems 78-6897-01 manual Determining the Destination ATM Switch Router Nsap Address

Page 46

Configuring the ATM Switch Router

Determining the Destination ATM Switch Router NSAP Address

Determine the destination ATM switch router NSAP address for the interface. See the ATM switch router C in Figure3-3.

Take these steps:

Step Command

1 Switch# show atm addresses

Purpose

On the destination ATM switch router, display the destination ATM address. You need this address to complete the soft PVC. Write the address in the space provided below (or copy it to memory):

2(No command.)

Example

Switch# show atm address

Proceed to the next section, “Configuring the Source ATM Switch Router” to complete the soft PVC.

Switch Address(es): 47.00918100000000E04FACB401.00E04FACB401.00 active

Soft VC Address(es): 47.0091.8100.0000.00e0.4fac.b401.4000.0c84.9030.00 ATM-P9/1/3

47.0091.8100.0000.0061.E5B5.C011.1111.1122.2222.00 ATM0/0/1 47.0091.8100.0000.00e0.4fac.b401.4000.0c85.0020.00 ATM0/1/0 47.0091.8100.0000.00e0.4fac.b401.4000.0c85.0030.00 ATM0/1/1

ILMI Switch Prefix(es): 47.0091.8100.0000.00e0.4fac.b401

ILMI Configured Interface Prefix(es):

LECS Address(es): 47.0091.8100.0000.00e0.4fac.b401.00e0.4fac.b405.00

Switch#

Configuring SVCs, PVCs, SoftPVCs, PVPs, and VPTunnels 3-15

Image 46
Contents Strongly agree Strongly disagree Page ATM Switch Router Quick Software Configuration Guide Page ATM Switch Router Quick Software Configuration Guide About This Guide Chapter Using the Command-Line InterfaceChapter Getting Started Chapter Configuring Lane Chapter Configuring Tag Switching IndexViii ATMSwitch Router Quick Software Configuration Guide Purpose AudienceOrganization OrganizationRelated Documentation Chapter Title DescriptionConvention Description ConventionsConventions Boldface screen fontTips Cisco Connection OnlineCisco Connection Online Documentation CD-ROM Documentation CD-ROMXiv ATMSwitch Router Quick Software Configuration Guide Using the Command-Line Interface Getting Help Understanding Command ModesSwitch# configure terminal Getting HelpUnderstanding Interface Numbering Understanding Interface NumberingCard Numbering Card Numbering Catalyst8540MSR ShownSubcard Numbering Subcard NumberingPort Numbering Processor Card NumberingPort Numbering Example of Interface Numbering Example of Interface NumberingUndoing a Command or Feature Undoing a Command or FeatureDisplaying the Configuration Switch# more systemrunning-configSaving Configuration Changes Saving Configuration ChangesSwitch# copy systemrunning-config nvramstartup-config Where to Go Next Where to Go NextNaming the ATM Switch Router Getting StartedExample Naming the ATM Switch RouterStep Command VerifyAssigning a Password Assigning a PasswordSetting Up Remote Administrative Access Setting Up Remote Administrative AccessSwitch# show interface ethernet 6ATMSwitch Router Quick Software Configuration Guide Configuring SVCs, PVCs Soft PVCs, PVPs, VP Tunnels Configuring SVCsConfiguring the Router Configuring SVCsConfiguring the Router Configuring Signaling on the RoutersRouter# configure terminal Routerconfig# Switch# show atm vc interface atm Configuring the IP Address and ESI AddressRouter# configure terminal MultipointConfiguring the Router Purpose Switch# show interface atmNsap Addresses Router Step Command PurposeDetermining the Nsap Address Router# show interface atmConfigure a Map Group and Map List Configuring SVCs Step Command Router# pingConfiguring PVCs Configuring PVCsConfiguring the ATM Switch Router Vci interface atm card/subcard/port.vpt# vpi vciSwitchconfig-if#atm pvc 2 100 interface atm 0 0 any-vci Configuring the ATM Switch RouterSwitch# show atm vc interface atm 3/0/1 12ATM Switch Router Quick Software Configuration Guide Configuring Soft PVCs Configuring Soft PVCs Step Command PurposeConfiguring Soft PVCs Example Network for Configuring Soft PVCsSwitch# show atm addresses Determining the Destination ATM Switch Router Nsap AddressSwitch# show atm address Configuring the Source ATM Switch Router Switchconfig#Switch# show atm vc interface atm 0/0/0 Configuring Soft PVCs Step Command Configuring PVPs Configuring PVPsAtm Configuring VP Tunnels Configuring VP TunnelsVPIs and VPTs for the Example VP Tunnel Switch a Switch B Switchconfig# interface atm 3/0/2 Switchconfig-if#interface atm 3/0/2.99Switch# show atm interface atm 3/0/2.99 Atm vp24ATM Switch Router Quick Software Configuration Guide Configuring Lane Understanding Lane Components Understanding Lane on ATMUnderstanding Lane on ATM Addressing Implementing LaneSupporting LAN Protocols Implementing LaneConfiguring Lane Router and LAN Switch Requirements Assigning Components to Interfaces and SubinterfacesConfiguring a LEC Configuring a LECConfiguring the Lecs Configuring the LecsConfiguring the ATM Address of the Lecs Switchconfig# atm lecs-address lecsaddressConfiguring the Lecs Database Configuring the Lecs Database PurposeConfiguring the LES/BUS Configuring the LES/BUS Step CommandLane Configuration Examples Lane Configuration ExamplesATMSwitch# configure terminal ATM Switch RouterATMSwitch# show lane default-atm-addresses interface ATM0 ATMSwitch# copy systemrunning-config nvramstartup-configATMSwitch# show lane config LE BUS ATM0.1Router1# more systemrunning-config ATMSwitch# show lane clientRouter1# configure terminal RouterATMconfig-if#lane server-bus ethernet engelan Catalyst 5500 SwitchATM enable ATM# configure terminal ATM# copy systemrunning-config nvramstartup-configATMconfig-subif#lane client ethernet 1 engelan ATM# show lane clientVerifying Connectivity Switch# show laneVerifying Connectivity ATMSwitch# ping ATMSwitch# show lane client 18ATMSwitch Router Quick Software Configuration Guide Configuring Tag Switching Software RestrictionsEnabling Tag Switching on the ATM Interface Configuring Tag Switching on an ATM Switch RouterConfiguring Tag Switching on an ATM Switch Router Switch# show tag-switching interfaces Enabling Tag Switching on the ATM Interface Step CommandSwitchconfig-if#ip unnumbered loopback ExamplesConfiguring the Routing Protocol Configuring the Routing Protocol Switch# show ip ospfConfiguring Tag Switching on a Router Configuring Tag Switching on a RouterTag Switching Configuration Example Tag Switching Configuration ExampleRouter 5-1 Configuration Router# show tag-switching interfaceRouter 5-2 Configuration Router 5-3 ConfigurationRouter 5-5 Configuration ATM Switch Router A5-4 ConfigurationAtmA5-4#configure terminal ATM Switch Router A6-4 Configuration AtmA6-4#configure terminalD E Index ATMSwitch Router Quick Software Configuration Guide Index Index ATMSwitch Router Quick Software Configuration Guide