EMC DS-16B manual Operation Menu Port Enable, Port Enable Accept? Yes No, Close Telnet Session

Page 45

Switch Management

Port Enable Pressing <Enter> while the Port Enable message is displayed opens a submenu where you select the port.

Operation Menu:

Port Enable

Pressing <Enter> while the selected port is displayed, enables the selected port. The LED associated with selected port changes from amber to green indicating the port has been enabled. When FL_Ports are enabled, the port initializes the loop attempting to be the master.

Port Enable

Accept? Yes No

Close Telnet Session

Reboot Pressing <Enter> while the Reboot message is displayed causes the switch to reboot immediately.

Operation Menu:

Reboot

Rebooting the switch causes it to immediately exit all current processes and states, and start the POST process. Exercise caution using the reboot command on a switch connected to the Fabric.

Pressing <Enter> while the screen above is selected, displays:

Reboot

Accept? Yes No

Selecting Yes causes the switch to immediately reboot. Selecting No or pressing <Tab/Esc> exits this function.

DS-16B Switch Menus

Image 45

Contents Hardware Reference Manual Departmental Switch Model DS-16BCopyright 2000 EMC Corporation. All rights reserved Departmental Switch Model DS-16B Hardware Reference Manual Trademark Information FCC Warning USA only Departmental Switch Model DS-16B Hardware Reference Manual Contents Chapter Front Panel Diagnostics Chapter Switch ManagementAppendix a Specifications Appendix B Switch SupportAppendix C Error Messages Departmental Switch Model DS-16B Hardware Reference Manual Figures Figures Preface For Information On See Related Publications Conventions Used in This ManualExamples of specific command entries that you Command line arguments when used in textArguments used in examples of command line Ask for Customer ServiceDepartmental Switch Model DS-16B Hardware Reference Manual Introduction System Components IntroductionFeatures DS-16B SwitchFollowing features IntroductionManageability PerformanceUnit may be managed in band or out of band via Telnet, via Ethernet portFabric Operating System ComponentsSystem GBICsInstallation Unpacking the Switch Site Considerations Power RequirementsCooling RequirementsTo install the adhesive rubber feet Installation ConsiderationsStandalone Fiber ChannelEthernet Verify Power-On SelfConnection Test PostDepartmental Switch Model DS-16B Hardware Reference Manual Switch Management SES Comparing Switch Management Access MethodsControl Buttons Managing Through Front Panel ButtonsActivating Menu Select Menu Configuration MenuDisplay Front panel buttons activates the displayFollowing menus are controlled using the front panel buttons DS-16B Switch MenusShows the front panel commands and their equivalent CommandsTelnet command Menu Front Panel Telnet Command DefaultUnset QuickLoop Port Configure QuickLoop Partner WWN Cmem Data Retention Test Configuration Menu Configuration menu SeeRatov Edtov Ethernet IP address 10 Configuration menuTo enter an IP address Ethernet Subnetmask noneFibre Channel IP Address To update the Fibre Channel’s IP addressFibre Channel IP address Fibre Channel SubnetmaskTo enter the gateway address Gateway addressDomain BBcreditRatov Ratov Pressing Enter while Ratov is selected, displaysEdtov Pressing Enter while Edtov is selected, displays EdtovOperating modes for the switch are Operating ModeFor the corresponding operating mode Operating modes are determined by the host adapter. The sixVC Class 2 VC Link CtlVC Class 3 VC MulticastReset to Default Accept? Yes No VC Priorities 0,1,2,2,2,2,3,3Frame Collection Method? Bundle/Piling Allows you to select commands Default valuesOperation Menu Menu. Pressing Enter while the Operation Menu is selectedOperation Menu Switch Offline Switch OnlineOperation Menu Switch Online Operation Menu Port DisablePort Enable Accept? Yes No Operation Menu Port EnableOperation Menu Reboot Reboot Accept? Yes NoStatus Menu Switch Name sw15Menu is informational only you cannot make changes to Status Menu SeeWorldwide Name 1000606900e Booted At Sat Sep 19 183420Firmware Version Current Date Mon Oct 21 102335Powered Time 137 days Boot Prom Date Jun 12 084829 PSTFlash Date Jun 12 084829 PST Up Time DayPort Throughput 75MB/s Module TypeL3Temperature Sensor Approximate Locations on Motherboard Temperature 36 34 37 36Feb 12 084829 Err SENSOR-FAILED-3 Error Log Selecting Error Log, then pressing Enter, displaysTest Menu LicensesLicenses 01f Front Panel Diagnostics Diagnostic Front Panel DiagnosticsThis section gives a diagnostic overview and discusses OverviewFault Diagnostic FrontRemoving Power Panel DisplaysIndicators Status and Activity IndicatorsFront Panel LED Port Color and flash speed of each port’s LED, as describedDiagnostics Post Power-OnDiagnostic Tests Switch Online Accept? Yes No Switch Offline Accept? Yes NoSystem Memory Test at 0x1021d460 len Offline Tests Offline & Online TestsRelated error messages DIAG-REGERR, DIAG-REGERRUNRST Related error messages DIAG-MEMORY, DIAG-MEMSZIf the memory tests OK, the front panel displays 0x10199a10 len 13091456 ramTest passedCentral MemTest passed Related error messages DIAG-CMBISTRO, DIAG-CMBISRFPort Loopback Test Aborted Related error messages DIAG-INIT, DIAG-PORTDIEDSpinSilk Press any button to terminate Push Button Test To exit Specifications General Specifications Table A-1 shows the switch specificationsSpecifications Description Table A-2 shows Fabric management specifications Fabric Management SpecificationsSafety Specifications Table A-3 Shows Safety specificationsSafety Switch’s primary operating environments are server rooms SpecificationsSpecification Value Optical PortDimensions Power SupplyRack Mount Dimensions Table Top DimensionsSwitch Support Support Tool Switch SupportError Messages Front Panel Error Message FormatsMessage Formats Feb 12To display error message from the front panel Failed test Replace Diagnostic Error Message FormatsError Message Error Number Test Name Error NameNumbers DIAG-CMBISRTO DIAG-TIMEOUTDIAG-CMBISRF DIAG-LCMEMTXDIAG-ERRSTAT CRC DIAG-ERRSTAT EncinDIAG-ERRSTAT Trunc DIAG-ERRSTAT 2LONGDIAG-ERRSTATCRL DIAG-ERRSTATENCINDIAG-ERRSTATTRUNC DIAG-ERRSTAT2LONGDIAG-PORTSTOPPED Message Description Probable Cause Action Error Message TablesCMI message received failed bad DIAG-ERRSTAT Asic failure Replace Err#1F26 Message Description Probable Cause RPC, Svcexit FLASH, BadmirrorRPC, Svcreg FCIU, IUBAD, L, SFCPH, EXCHBAD, L, S FCIU, IUCOUNT, L, SFCPH, EXCHFREE, L, S MQ, QWRITE, L, MSYS FLASHRD, Logerror SYS BADPTR, LogerrorSYS FLASHWR, Logerror TIMERS, MSG,LOGWARNINGLogerror MCAST, NoparentlsrUCAST, RRTIM, Logcritical Sales and Service Locations Locations International SalesDepartmental Switch Model DS-16B Hardware Reference Manual Departmental Switch Model DS-16B Hardware Reference Manual Index Index Departmental Switch Model DS-16B Hardware Reference Manual Departmental Switch Model DS-16B Hardware Reference Manual