Extron electronic 50 manual Installation, cont’d, RS-232/422 connection

Page 18

Installation, cont’d

When making connections for the Matrix 50 Series Switcher from existing audio cables, see figure 2-6. A mono audio connector consists of the tip and sleeve. A stereo audio connector consists of the tip, ring and sleeve. The ring, tip, and sleeve wires are also shown on the captive screw audio connector diagrams, figure 2-5 and figure 2-7.

Tip

Sleeve

Tip

Sleeve

Unbalanced Input

(high impedance)

Tip

Ring

Sleeve (s)

Tip

Ring

Balanced Input

(high impedance)

600 ohms

Tip

Ring

Sleeve (s)

Tip

Ring

600ohms

Balanced Input

(600 ohms)

Figure 2-5 — Captive screw connector wiring for inputs

Tip

Sleeve

Tip (left)

Sleeve (Gnd)

 

 

 

Ring (right)

 

Tip (signal)

 

Tip (left)

 

Sleeve (Gnd)

Sleeve (Gnd)

 

Unbalanced mono

 

Unbalanced stereo

Figure 2-6 — Phono audio connectors

The audio level for each input can be individually set, via the front panel or RS-232/422, to ensure that the level on the output does not vary from input to input. See chapter 3, Operation, chapter 4, Programmer’s Guide, and chapter 5, Matrix Software for details.

5Connections for audio outputs — These 3.5 mm, 5-pole captive screw connectors output the selected unamplified, line level audio. Connect audio devices, such as an audio amplifier or powered speakers. See figure 2-7 to properly wire an output connector.

Tip See caution Sleeve Tip

See caution

Tip

Ring

Sleeve (s)

Tip

Ring

Unbalanced Output

Balanced Output

Figure 2-7 — Captive screw connector wiring for audio output

CAUTION

Connect the sleeve to ground (Gnd). Connecting the sleeve to a negative (-) terminal will damage the audio output circuits.

By default, the audio output follows the video switch. Audio breakaway, commanded via the front panel, under RS-232/422 control, or Windows- based control program, allows you to select from any one of the audio input sources. See chapter 3, Operation, chapter 4, Programmer’s Guide, and chapter 5, Matrix Software for details.

RS-232/422 connection

6Remote/RS-232/RS-422 port — Connect a host device, such as a computer or touch panel control, to the Matrix 50 via

5

1

1

5

this 9-pin D connector for serial

 

 

 

 

RS-232/RS-422 control.

9

6

6

9

If desired, attach an MCP 1000 remote

control panel master unit to the

Female

Male

switcher’s RS-232/RS-422 connector.

2-4 Matrix 50 Series Switchers • Installation

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Matrix Audio/Video Switchers Matrix 50 SeriesSicherheitsanleitungen Deutsch Safety Instructions EnglishConsignes de Sécurité Français Instrucciones de seguridad EspañolQuick Start Matrix 50 Series Switchers QS-1Quick Start Matrix 50 Series Switchers, cont’d Table of Contents Table of Contents, cont’d Matrix 50 Series Switchers Table of Contents Iii Iv Matrix 50 Series Switchers Table of Contents One About the Matrix 50 Series Switchers Matrix 50 Series Switchers IntroductionIntroductiontroduction, cont’d Features MatrixMatrix 50 switcher Introduction, cont’dMatrix 50 Series Switchers Introduction Introduction, cont’d Two Matrix 50 Series Switchers Installation Installationstallation, cont’dRack Mounting the Switcher Cabling and Rear Panel ViewsPower connection Video input and output connections video models onlyAudio input and output connections audio models only Installation, cont’d RS-232/422 connectionExternal sync connection Simple external sync connection exampleAdditional rear panel views Multiple device external sync connection exampleThree Definitions Front Panel Controls and IndicatorsOperationeration, cont’d Input buttons, output buttons, and LEDsControls Operation, cont’d PowerCreating a configuration Front Panel OperationsExample 1 Creating a set of video and audio ties Example 1 Creating a tieExample 2 Adding a tie to a set of video and audio ties Example 3 Removing a tie from a set of video and audio tiesViewing a configuration Example 3 Selecting audio and selecting inputExample 4 Viewing the current configuration Example 4e Viewing the current configuration, audio only Muting and unmuting video and/or audio Example 5 Muting and unmuting an outputUsing global memory presets 11 Example 5, step d Muting and unmuting outputsExample 6 Saving a preset Example 7 Recalling a presetViewing and adjusting the audio level Example 8 Viewing and adjusting an audio levelExecutive mode front panel security lockout 14 Example 8 Viewing the audio levelPlasma display S-video problem TroubleshootingSystem reset to factory defaults WorksheetsWorksheet example 1 System equipment 16 Worksheet example 1 System equipmentWorksheet example 2 Daily configuration 17 Worksheet example 2 Daily configurationWorksheet example 3 Test configuration 18 Worksheet example 3 Test configurationConfiguration worksheet Operation, cont’d Four Matrix 50 Series Switchers Programmer’s Guide Host-to-Switcher InstructionsSwitcher-Initiated Messages Programmer’ser’sGuide,Guidecont’dSwitcher Error Responses Using the Command/Response TableCommand/Response Table Command Ascii Command Response Additional descriptionProgrammer’s Guide, cont’d Command/response table for SIS commands Cont’d View ties, gain, and presets Five Using the software Matrix Switcher+ Control ProgramInstalling the software MatrixSoftware,cont’dExtron Matrix Switcher+ Control Program window blank Windows buttonsMatrix Software, cont’d Windows menusUsing emulation mode Using the help systemButton-Label Generator Extron’s Button-Label Generator window AAppendix a Specificationsecifications, cont’d Matrix 50 Series Switchers SpecificationsAudio input Part Numbers Specifications, cont’dMatrix 50 Series switchers part numbers Matrix 50 Option KitsOptional Accessories CablesPre-cut cables Extron Part BNC-4 Mini HR CableVideo Cable AppendixBB Matrix 50 Series Switchers Reference Information Hardware ProceduresOpening the switcher ReferenceInformation,co t’dClosing the switcher Figure B-2 Side view, Matrix 50 S-video and audio switcherInstalling a video module Reference Information, cont’dRemoving a video module Installing an audio module Removing a video module on page B-5On page B-3 Removing an audio moduleSwapping the serial ports Installing a firmware update Figure B-8 Key and pin 1 markSetting the front panel jumper Replacing the AC fuseMatrix 50 Series Switchers Reference Information B-11 Button LabelsBlank Matrix 50 Series Switchers Reference Information B-13 Figure B-10 Button label blanks, 12-button stripReference Information, cont’d FCC Class a Notice Extron’s Warranty Extron Electronics, USA
Top Page Image Contents