Extron electronic 50 manual Example 4e Viewing the current configuration, audio only

Page 29

DPress and release the input 5 button (figure 3-8). The input 5 LED lights.

If ties are established for input 5, all output LEDs toggle; outputs with no ties turn off and the LEDs associated with all outputs tied to input 5 (audio, video, or audio and video ties) light. If no ties are established for input 5, all output LEDs turn off.

If audio is broken away, the Audio LED blinks.

				5
			Press
			D
					INPUTS
1	2	3	4	5	6	7
1	2	3	4	5	6	7
			OUTPUTS

	LED key:			= off,	= on, B = blinking
							B	D
						VIDEO	AUDIO
8	9	10	11	12
					CONTROL	I/O
8					ENTER PRESET VIEW ESC	VIDEO	AUDIO

D

1

3

4

8

Figure 3-8 — Example 4d: Viewing the current configuration, video and audio

A set of ties can also be viewed by selecting a tied output. To demonstrate this, note the number of a lit output LED, and press and release the output button for an unlit (untied) output LED. Observe that all of the untied outputs light. Then press the output button for the output LED noted previously and observe that the selected output LED, the tied input LED (input 5), and the output LEDs light for all of the outputs that are tied to the input.

EPress and release the Video button to toggle the Video LED off (figure 3-9). If audio is broken away, the Audio LED stops blinking and lights steadily.

								LED key:			= off,	= on
					INPUTS
1	2	3	4	5	6	7	8	9	10	11	12
1	2	3	4	5	6	7	8
			OUTPUTS
									E
		3					8

	Press
	E
		VIDEO	AUDIO
CONTROL		I/O
ENTER PRESET VIEW	ESC	VIDEO	AUDIO

Figure 3-9 — Example 4e: Viewing the current configuration, audio only

If audio ties are established for input 5, the output LEDs for all audio outputs tied to input 5 light. If no ties are established for input 5, all output LEDs turn off.

FPress and release the Video and Audio buttons to toggle the Video LED on and the Audio LED off (figure 3-10).

If video ties are established for input 5, the output LEDs for all video outputs tied to input 5 light. If no ties are established for input 5, all output LEDs turn off.

Matrix 50 Series Switchers • Operation

3-9

Image 29

Contents Matrix 50 Series Matrix Audio/Video SwitchersConsignes de Sécurité Français Safety Instructions EnglishSicherheitsanleitungen Deutsch Instrucciones de seguridad EspañolQS-1 Quick Start Matrix 50 Series SwitchersQuick Start Matrix 50 Series Switchers, cont’d Table of Contents Table of Contents, cont’d Matrix 50 Series Switchers Table of Contents Iii Iv Matrix 50 Series Switchers Table of Contents One Introductiontroduction, cont’d About the Matrix 50 Series SwitchersMatrix 50 Series Switchers Introduction Matrix FeaturesIntroduction, cont’d Matrix 50 switcherMatrix 50 Series Switchers Introduction Introduction, cont’d Two Rack Mounting the Switcher Installationstallation, cont’dMatrix 50 Series Switchers Installation Cabling and Rear Panel ViewsAudio input and output connections audio models only Power connectionVideo input and output connections video models only RS-232/422 connection Installation, cont’dSimple external sync connection example External sync connectionMultiple device external sync connection example Additional rear panel viewsThree Operationeration, cont’d Front Panel Controls and IndicatorsDefinitions Input buttons, output buttons, and LEDsControls Creating a configuration PowerOperation, cont’d Front Panel OperationsExample 1 Creating a tie Example 1 Creating a set of video and audio tiesExample 3 Removing a tie from a set of video and audio ties Example 2 Adding a tie to a set of video and audio tiesExample 3 Selecting audio and selecting input Viewing a configurationExample 4 Viewing the current configuration Example 4e Viewing the current configuration, audio only Example 5 Muting and unmuting an output Muting and unmuting video and/or audio11 Example 5, step d Muting and unmuting outputs Using global memory presetsExample 7 Recalling a preset Example 6 Saving a presetExample 8 Viewing and adjusting an audio level Viewing and adjusting the audio level14 Example 8 Viewing the audio level Executive mode front panel security lockoutSystem reset to factory defaults TroubleshootingPlasma display S-video problem Worksheets16 Worksheet example 1 System equipment Worksheet example 1 System equipment17 Worksheet example 2 Daily configuration Worksheet example 2 Daily configuration18 Worksheet example 3 Test configuration Worksheet example 3 Test configurationConfiguration worksheet Operation, cont’d Four Switcher-Initiated Messages Host-to-Switcher InstructionsMatrix 50 Series Switchers Programmer’s Guide Programmer’ser’sGuide,Guidecont’dUsing the Command/Response Table Switcher Error ResponsesProgrammer’s Guide, cont’d Command/Response TableCommand Ascii Command Response Additional description Command/response table for SIS commands Cont’d View ties, gain, and presets Five Installing the software Matrix Switcher+ Control ProgramUsing the software MatrixSoftware,cont’dWindows buttons Extron Matrix Switcher+ Control Program window blankWindows menus Matrix Software, cont’dButton-Label Generator Using emulation modeUsing the help system Extron’s Button-Label Generator window AAppendix a Matrix 50 Series Switchers Specifications Specificationsecifications, cont’dAudio input Matrix 50 Series switchers part numbers Specifications, cont’dPart Numbers Matrix 50 Option KitsCables Optional AccessoriesVideo Cable Pre-cut cablesExtron Part BNC-4 Mini HR Cable AppendixBB Opening the switcher Hardware ProceduresMatrix 50 Series Switchers Reference Information ReferenceInformation,co t’dFigure B-2 Side view, Matrix 50 S-video and audio switcher Closing the switcherReference Information, cont’d Installing a video moduleRemoving a video module Removing a video module on page B-5 Installing an audio moduleRemoving an audio module On page B-3Swapping the serial ports Figure B-8 Key and pin 1 mark Installing a firmware updateReplacing the AC fuse Setting the front panel jumperButton Labels Matrix 50 Series Switchers Reference Information B-11Blank Figure B-10 Button label blanks, 12-button strip Matrix 50 Series Switchers Reference Information B-13Reference Information, cont’d FCC Class a Notice Extron’s Warranty Extron Electronics, USA