Extron electronic 50 manual Reference Information, cont’d, Installing a video module

Page 62

Reference Information, cont’d

Installing a video module

1.Follow the instructions in Opening the switcher on page B-2 to remove the top cover.

2.Remove the bus ribbon cable that connects the video and audio modules to the front panel board by pressing the two receptacle

Ribbon cable

tabs on the top cable outward, as shown at the left, and

pulling back gently on the cable connector to remove it

Connector

from the receptacle. Do this for each video or audio

Self-latching receptacle

board connection and move the ribbon cable out of the

way.

3.

Follow the instructions in Removing a video module on page B-5 to remove any

existing video modules and set them aside.

4.

Remove any plastic plugs that are located where they will block the

installation of video modules to be installed by

Locking

squeezing the locking tabs together and pushing the

tabs

plug out through the back of the chassis.

Squeeze

If you are also installing or removing an audio

module, see Installing an audio module, step

3, on page B-6 or Removing an audio

module on page B-7, before continuing to

install the video modules. Return here when

finished with the audio module procedure.

5.

Mount the new video module(s) and any module(s) removed in step 3,

starting at the lowest required video module location. For example, if

upgrading the switcher from composite video to S-video, mount a video module in the second location, and the next module in the top location, leaving the bottom video module location empty.

a. Insert the video module into the Matrix 50 switcher chassis and position the module such that its BNC connectors protrude through the holes in the switcher’s rear panel in the proper module location (figure B-3).

1 hex nut on each BNC connector

Plug

Figure B-3 — Installing a video module

b. Using an Extron BNC extraction tool (part #100-096-01) or a 9/16”, deep well socket with thin walls, secure the video module to the switcher’s rear panel by installing a hex nut on each BNC connector on the video module.

B-4 Matrix 50 Series Switchers • Reference Information

Image 62

Contents Matrix Audio/Video Switchers Matrix 50 SeriesSicherheitsanleitungen Deutsch Safety Instructions EnglishConsignes de Sécurité Français Instrucciones de seguridad EspañolQuick Start Matrix 50 Series Switchers QS-1Quick Start Matrix 50 Series Switchers, cont’d Table of Contents Table of Contents, cont’d Matrix 50 Series Switchers Table of Contents Iii Iv Matrix 50 Series Switchers Table of Contents One Introductiontroduction, cont’d About the Matrix 50 Series SwitchersMatrix 50 Series Switchers Introduction Features MatrixMatrix 50 switcher Introduction, cont’dMatrix 50 Series Switchers Introduction Introduction, cont’d Two Matrix 50 Series Switchers Installation Installationstallation, cont’dRack Mounting the Switcher Cabling and Rear Panel ViewsAudio input and output connections audio models only Power connectionVideo input and output connections video models only Installation, cont’d RS-232/422 connectionExternal sync connection Simple external sync connection exampleAdditional rear panel views Multiple device external sync connection exampleThree Definitions Front Panel Controls and IndicatorsOperationeration, cont’d Input buttons, output buttons, and LEDsControls Operation, cont’d PowerCreating a configuration Front Panel OperationsExample 1 Creating a set of video and audio ties Example 1 Creating a tieExample 2 Adding a tie to a set of video and audio ties Example 3 Removing a tie from a set of video and audio tiesViewing a configuration Example 3 Selecting audio and selecting inputExample 4 Viewing the current configuration Example 4e Viewing the current configuration, audio only Muting and unmuting video and/or audio Example 5 Muting and unmuting an outputUsing global memory presets 11 Example 5, step d Muting and unmuting outputsExample 6 Saving a preset Example 7 Recalling a presetViewing and adjusting the audio level Example 8 Viewing and adjusting an audio levelExecutive mode front panel security lockout 14 Example 8 Viewing the audio levelPlasma display S-video problem TroubleshootingSystem reset to factory defaults WorksheetsWorksheet example 1 System equipment 16 Worksheet example 1 System equipmentWorksheet example 2 Daily configuration 17 Worksheet example 2 Daily configurationWorksheet example 3 Test configuration 18 Worksheet example 3 Test configurationConfiguration worksheet Operation, cont’d Four Matrix 50 Series Switchers Programmer’s Guide Host-to-Switcher InstructionsSwitcher-Initiated Messages Programmer’ser’sGuide,Guidecont’dSwitcher Error Responses Using the Command/Response TableProgrammer’s Guide, cont’d Command/Response TableCommand Ascii Command Response Additional description Command/response table for SIS commands Cont’d View ties, gain, and presets Five Using the software Matrix Switcher+ Control ProgramInstalling the software MatrixSoftware,cont’dExtron Matrix Switcher+ Control Program window blank Windows buttonsMatrix Software, cont’d Windows menusButton-Label Generator Using emulation modeUsing the help system Extron’s Button-Label Generator window AAppendix a Specificationsecifications, cont’d Matrix 50 Series Switchers SpecificationsAudio input Part Numbers Specifications, cont’dMatrix 50 Series switchers part numbers Matrix 50 Option KitsOptional Accessories CablesVideo Cable Pre-cut cablesExtron Part BNC-4 Mini HR Cable AppendixBB Matrix 50 Series Switchers Reference Information Hardware ProceduresOpening the switcher ReferenceInformation,co t’dClosing the switcher Figure B-2 Side view, Matrix 50 S-video and audio switcherInstalling a video module Reference Information, cont’dRemoving a video module Installing an audio module Removing a video module on page B-5On page B-3 Removing an audio moduleSwapping the serial ports Installing a firmware update Figure B-8 Key and pin 1 markSetting the front panel jumper Replacing the AC fuseMatrix 50 Series Switchers Reference Information B-11 Button LabelsBlank Matrix 50 Series Switchers Reference Information B-13 Figure B-10 Button label blanks, 12-button stripReference Information, cont’d FCC Class a Notice Extron’s Warranty Extron Electronics, USA