Extron electronic 50 manual Swapping the serial ports

Page 66
Matrix 50 Series Switchers • Reference Information
9.
Reconnect the input and output cables.
If you choose to check for proper operation before putting the cover back on, ensure that tools and hands are outside the switcher, and then connect the power cord to the unit and to an AC source. The switcher should power up normally. Unplug the AC power cord, and reinstall the switcher.
7. Attach the power cord to the switcher and to the AC power source. Ensure the switcher is working properly.
8. If the switcher was removed from a rack, remove its power cord, reattach the switcher to the rack, and reconnect the power cord.
Self-latching receptacle
6. Reinstall the switcher’s cover. See Closing the switcher on page B-3.
Self-latching receptacle Ribbon cable
5. Plug the cable in to the desired receptacle by aligning the holes in the connector with the pins in the RS-232 or RS-422 receptacle, and pressing evenly until the receptacle tabs lock into place.
Connector
Ribbon cable
4.
Remove the RS-232/RS-422 ribbon cable by pressing the two RS-232/RS-422 receptacle tabs outward as shown at the left, and pull up evenly
on the cable connector to remove it from the current receptacle.
Figure B-7 — Front panel board, Matrix 50 Series switcher
3. On the side of the front panel board that faces the rear of the switcher, locate the RS-232/RS-422 ribbon cable. The RS-422 ribbon cable receptacle, which is normally empty, is located to the left of the RS-232 ribbon cable receptacle.

Reference Information, cont’d

9.

If not already done, reconnect the AC power, input, and output cables.

Swapping the serial ports

The Matrix 50 switchers are factory configured for RS-232 use. If you want to use RS-422 and the switcher is configured for RS-232, or if you want to use RS-232 and the switcher is configured for RS-422, do the following:

1.Follow the instructions in Opening the switcher on page B-2 to remove the top cover.

2.Locate the switcher’s front panel board (figure B-7).

Label includes

Key Extron part number &

Software version (Vx.xx)

 

Pin 1 (red stripe on ribbon cable )

 

JMP9

19-965-01 Vx.xx

JMP8

 

JMP7

 

JMP6

 

JMP5

 

JMP4

 

JMP3

 

JMP2

 

J1 RS-422

Slots for removing IC

receptacle

J2 RS-232

with PLCC IC puller

receptacle

 

U7

 

 

19-965-01 Vx.xx

B-8

Page 65 Page 67
Image 66
Page 65 Page 67
Contents Matrix Audio/Video Switchers Matrix 50 SeriesSicherheitsanleitungen Deutsch Safety Instructions EnglishConsignes de Sécurité Français Instrucciones de seguridad EspañolQuick Start Matrix 50 Series Switchers QS-1Quick Start Matrix 50 Series Switchers, cont’d Table of Contents Table of Contents, cont’d Matrix 50 Series Switchers Table of Contents Iii Iv Matrix 50 Series Switchers Table of Contents One About the Matrix 50 Series Switchers Matrix 50 Series Switchers IntroductionIntroductiontroduction, cont’d Features MatrixMatrix 50 switcher Introduction, cont’dMatrix 50 Series Switchers Introduction Introduction, cont’d Two Matrix 50 Series Switchers Installation Installationstallation, cont’dRack Mounting the Switcher Cabling and Rear Panel ViewsPower connection Video input and output connections video models onlyAudio input and output connections audio models only Installation, cont’d RS-232/422 connectionExternal sync connection Simple external sync connection exampleAdditional rear panel views Multiple device external sync connection exampleThree Definitions Front Panel Controls and IndicatorsOperationeration, cont’d Input buttons, output buttons, and LEDsControls Operation, cont’d PowerCreating a configuration Front Panel OperationsExample 1 Creating a set of video and audio ties Example 1 Creating a tieExample 2 Adding a tie to a set of video and audio ties Example 3 Removing a tie from a set of video and audio tiesViewing a configuration Example 3 Selecting audio and selecting inputExample 4 Viewing the current configuration Example 4e Viewing the current configuration, audio only Muting and unmuting video and/or audio Example 5 Muting and unmuting an outputUsing global memory presets 11 Example 5, step d Muting and unmuting outputsExample 6 Saving a preset Example 7 Recalling a presetViewing and adjusting the audio level Example 8 Viewing and adjusting an audio levelExecutive mode front panel security lockout 14 Example 8 Viewing the audio levelPlasma display S-video problem TroubleshootingSystem reset to factory defaults WorksheetsWorksheet example 1 System equipment 16 Worksheet example 1 System equipmentWorksheet example 2 Daily configuration 17 Worksheet example 2 Daily configurationWorksheet example 3 Test configuration 18 Worksheet example 3 Test configurationConfiguration worksheet Operation, cont’d Four Matrix 50 Series Switchers Programmer’s Guide Host-to-Switcher InstructionsSwitcher-Initiated Messages Programmer’ser’sGuide,Guidecont’dSwitcher Error Responses Using the Command/Response TableCommand/Response Table Command Ascii Command Response Additional descriptionProgrammer’s Guide, cont’d Command/response table for SIS commands Cont’d View ties, gain, and presets Five Using the software Matrix Switcher+ Control ProgramInstalling the software MatrixSoftware,cont’dExtron Matrix Switcher+ Control Program window blank Windows buttonsMatrix Software, cont’d Windows menusUsing emulation mode Using the help systemButton-Label Generator Extron’s Button-Label Generator window AAppendix a Specificationsecifications, cont’d Matrix 50 Series Switchers SpecificationsAudio input Part Numbers Specifications, cont’dMatrix 50 Series switchers part numbers Matrix 50 Option KitsOptional Accessories CablesPre-cut cables Extron Part BNC-4 Mini HR CableVideo Cable AppendixBB Matrix 50 Series Switchers Reference Information Hardware ProceduresOpening the switcher ReferenceInformation,co t’dClosing the switcher Figure B-2 Side view, Matrix 50 S-video and audio switcherInstalling a video module Reference Information, cont’dRemoving a video module Installing an audio module Removing a video module on page B-5On page B-3 Removing an audio moduleSwapping the serial ports Installing a firmware update Figure B-8 Key and pin 1 markSetting the front panel jumper Replacing the AC fuseMatrix 50 Series Switchers Reference Information B-11 Button LabelsBlank Matrix 50 Series Switchers Reference Information B-13 Figure B-10 Button label blanks, 12-button stripReference Information, cont’d FCC Class a Notice Extron’s Warranty Extron Electronics, USA
Top Page Image Contents