Extron electronic 50 manual Worksheet example 2 Daily configuration

Page 37

Worksheet example 2: Daily configuration

Figure 3-17 continues from worksheet example 1 by showing the video and audio ties that make up the configuration of preset 3, a solid ink line shows video ties, and a dashed pencil line shows the audio ties. In this example, the image of the presenter, from the main podium camera (input 1) is displayed on the main podium monitor (output 6) and taped on the VCR (output 5) for a tape archive. The audio from the presenter’s microphone (input 4) is also routed to the podium monitor (output 6) and the VCR (output 5). Videotaped material from two VCRs (inputs 6 and 7) is displayed on two rear projection displays (outputs 3 and 4). Classical music from the CD player (input 5) is played on the lunch room stereo (output 8). Meanwhile security cameras (inputs 2 and 3) are routed to two local monitors (outputs 1 and 2).

	Camera	Security	Lobby	Podium
	main	camera	security
				mic
	podium	#2	camera

	1	2	3	4

		Input sources
Audio		Class		Class		Class		Class
		Class		Class		Class		Class
		room #1		room #2		room #1		room #2
CD		room #1		room #2		room #1		room #2
CD		VCR		VCR		LD		LD
		VCR		VCR		LD		LD
5	6		7		8		9		10	11

VTG

200

12

1

2

3

4

5

6

7

Main

Lobby

Class

Class

Archive

Main

hall

room #1

room #2

VCR

podium

monitor

monitor

rear proj

rear proj

monitor

Output destinations

Preset #

3

Title: Daily configuration

Video:

Audio:

8

Lunch

room

stereo

Fill in the preset number, use colors or dashes, etc. to make connecting lines. Indicate if the configuration is for Video, Audio, or both.

Figure 3-17 — Worksheet example 2: Daily configuration

Matrix 50 Series Switchers • Operation 3-17

Image 37

Contents Matrix 50 Series Matrix Audio/Video SwitchersConsignes de Sécurité Français Safety Instructions EnglishSicherheitsanleitungen Deutsch Instrucciones de seguridad EspañolQS-1 Quick Start Matrix 50 Series SwitchersQuick Start Matrix 50 Series Switchers, cont’d Table of Contents Table of Contents, cont’d Matrix 50 Series Switchers Table of Contents Iii Iv Matrix 50 Series Switchers Table of Contents One Matrix 50 Series Switchers Introduction About the Matrix 50 Series SwitchersIntroductiontroduction, cont’d Matrix FeaturesIntroduction, cont’d Matrix 50 switcherMatrix 50 Series Switchers Introduction Introduction, cont’d Two Rack Mounting the Switcher Installationstallation, cont’dMatrix 50 Series Switchers Installation Cabling and Rear Panel ViewsVideo input and output connections video models only Power connectionAudio input and output connections audio models only RS-232/422 connection Installation, cont’dSimple external sync connection example External sync connectionMultiple device external sync connection example Additional rear panel viewsThree Operationeration, cont’d Front Panel Controls and IndicatorsDefinitions Input buttons, output buttons, and LEDsControls Creating a configuration PowerOperation, cont’d Front Panel OperationsExample 1 Creating a tie Example 1 Creating a set of video and audio tiesExample 3 Removing a tie from a set of video and audio ties Example 2 Adding a tie to a set of video and audio tiesExample 3 Selecting audio and selecting input Viewing a configurationExample 4 Viewing the current configuration Example 4e Viewing the current configuration, audio only Example 5 Muting and unmuting an output Muting and unmuting video and/or audio11 Example 5, step d Muting and unmuting outputs Using global memory presetsExample 7 Recalling a preset Example 6 Saving a presetExample 8 Viewing and adjusting an audio level Viewing and adjusting the audio level14 Example 8 Viewing the audio level Executive mode front panel security lockoutSystem reset to factory defaults TroubleshootingPlasma display S-video problem Worksheets16 Worksheet example 1 System equipment Worksheet example 1 System equipment17 Worksheet example 2 Daily configuration Worksheet example 2 Daily configuration18 Worksheet example 3 Test configuration Worksheet example 3 Test configurationConfiguration worksheet Operation, cont’d Four Switcher-Initiated Messages Host-to-Switcher InstructionsMatrix 50 Series Switchers Programmer’s Guide Programmer’ser’sGuide,Guidecont’dUsing the Command/Response Table Switcher Error ResponsesCommand Ascii Command Response Additional description Command/Response TableProgrammer’s Guide, cont’d Command/response table for SIS commands Cont’d View ties, gain, and presets Five Installing the software Matrix Switcher+ Control ProgramUsing the software MatrixSoftware,cont’dWindows buttons Extron Matrix Switcher+ Control Program window blankWindows menus Matrix Software, cont’dUsing the help system Using emulation modeButton-Label Generator Extron’s Button-Label Generator window AAppendix a Matrix 50 Series Switchers Specifications Specificationsecifications, cont’dAudio input Matrix 50 Series switchers part numbers Specifications, cont’dPart Numbers Matrix 50 Option KitsCables Optional AccessoriesExtron Part BNC-4 Mini HR Cable Pre-cut cablesVideo Cable AppendixBB Opening the switcher Hardware ProceduresMatrix 50 Series Switchers Reference Information ReferenceInformation,co t’dFigure B-2 Side view, Matrix 50 S-video and audio switcher Closing the switcherReference Information, cont’d Installing a video moduleRemoving a video module Removing a video module on page B-5 Installing an audio moduleRemoving an audio module On page B-3Swapping the serial ports Figure B-8 Key and pin 1 mark Installing a firmware updateReplacing the AC fuse Setting the front panel jumperButton Labels Matrix 50 Series Switchers Reference Information B-11Blank Figure B-10 Button label blanks, 12-button strip Matrix 50 Series Switchers Reference Information B-13Reference Information, cont’d FCC Class a Notice Extron’s Warranty Extron Electronics, USA