Extron electronic 50 manual Switcher Error Responses, Using the Command/Response Table

Page 43

The switcher does not expect a response from the host, but, for example, the host program might request a new status.

Switcher Error Responses

When the switcher receives an SIS command and determines that it is valid, it performs the command and sends a response to the host device. If the switcher is unable to perform the command because the command is invalid or contains invalid parameters, the switcher returns an error response to the host. The error response codes are:

E01 — Invalid input channel number (too large)

E10 — Invalid command

E11 — Invalid preset number (too large)

E12 — Invalid output number (too large)

E13 — Invalid value (out of range)

E14 — Illegal command for this configuration

E17 — Timeout (only caused by direct write of global presets)

Using the Command/Response Table

The command/response table begins on the next page. Lower case letters are acceptable in the command field only where indicated. Symbols are used throughout the table to represent variables in the command/response fields. Command and response examples are shown throughout the table.

ASCII to HEX Conversion Table

Space

Matrix 50 Series Switchers • Programmer’s Guide

4-3

Image 43

Contents Matrix 50 Series Matrix Audio/Video SwitchersInstrucciones de seguridad Español Safety Instructions EnglishConsignes de Sécurité Français Sicherheitsanleitungen DeutschQS-1 Quick Start Matrix 50 Series SwitchersQuick Start Matrix 50 Series Switchers, cont’d Table of Contents Table of Contents, cont’d Matrix 50 Series Switchers Table of Contents Iii Iv Matrix 50 Series Switchers Table of Contents One Matrix 50 Series Switchers Introduction About the Matrix 50 Series SwitchersIntroductiontroduction, cont’d Matrix FeaturesIntroduction, cont’d Matrix 50 switcherMatrix 50 Series Switchers Introduction Introduction, cont’d Two Cabling and Rear Panel Views Installationstallation, cont’dRack Mounting the Switcher Matrix 50 Series Switchers InstallationVideo input and output connections video models only Power connectionAudio input and output connections audio models only RS-232/422 connection Installation, cont’dSimple external sync connection example External sync connectionMultiple device external sync connection example Additional rear panel viewsThree Input buttons, output buttons, and LEDs Front Panel Controls and IndicatorsOperationeration, cont’d DefinitionsControls Front Panel Operations PowerCreating a configuration Operation, cont’dExample 1 Creating a tie Example 1 Creating a set of video and audio tiesExample 3 Removing a tie from a set of video and audio ties Example 2 Adding a tie to a set of video and audio tiesExample 3 Selecting audio and selecting input Viewing a configurationExample 4 Viewing the current configuration Example 4e Viewing the current configuration, audio only Example 5 Muting and unmuting an output Muting and unmuting video and/or audio11 Example 5, step d Muting and unmuting outputs Using global memory presetsExample 7 Recalling a preset Example 6 Saving a presetExample 8 Viewing and adjusting an audio level Viewing and adjusting the audio level14 Example 8 Viewing the audio level Executive mode front panel security lockoutWorksheets TroubleshootingSystem reset to factory defaults Plasma display S-video problem16 Worksheet example 1 System equipment Worksheet example 1 System equipment17 Worksheet example 2 Daily configuration Worksheet example 2 Daily configuration18 Worksheet example 3 Test configuration Worksheet example 3 Test configurationConfiguration worksheet Operation, cont’d Four Programmer’ser’sGuide,Guidecont’d Host-to-Switcher InstructionsSwitcher-Initiated Messages Matrix 50 Series Switchers Programmer’s GuideUsing the Command/Response Table Switcher Error ResponsesCommand Ascii Command Response Additional description Command/Response TableProgrammer’s Guide, cont’d Command/response table for SIS commands Cont’d View ties, gain, and presets Five MatrixSoftware,cont’d Matrix Switcher+ Control ProgramInstalling the software Using the softwareWindows buttons Extron Matrix Switcher+ Control Program window blankWindows menus Matrix Software, cont’dUsing the help system Using emulation modeButton-Label Generator Extron’s Button-Label Generator window AAppendix a Matrix 50 Series Switchers Specifications Specificationsecifications, cont’dAudio input Matrix 50 Option Kits Specifications, cont’dMatrix 50 Series switchers part numbers Part NumbersCables Optional AccessoriesExtron Part BNC-4 Mini HR Cable Pre-cut cablesVideo Cable AppendixBB ReferenceInformation,co t’d Hardware ProceduresOpening the switcher Matrix 50 Series Switchers Reference InformationFigure B-2 Side view, Matrix 50 S-video and audio switcher Closing the switcherReference Information, cont’d Installing a video moduleRemoving a video module Removing a video module on page B-5 Installing an audio moduleRemoving an audio module On page B-3Swapping the serial ports Figure B-8 Key and pin 1 mark Installing a firmware updateReplacing the AC fuse Setting the front panel jumperButton Labels Matrix 50 Series Switchers Reference Information B-11Blank Figure B-10 Button label blanks, 12-button strip Matrix 50 Series Switchers Reference Information B-13Reference Information, cont’d FCC Class a Notice Extron’s Warranty Extron Electronics, USA