Extron electronic 50 manual Viewing a configuration, Example 3 Selecting audio and selecting input

Page 27

CPress and release the input 5 button. The input 5 LED lights. If the steps in Example 1 have been completed, the output 3, output 4, and output 8 LEDs light to indicate ties created in Example 1.

The output 1 LED does not light, even if the steps in Example 2 have been completed, because Example 2 added a video tie only.

				5					LED key:		= off,	= on,
									LED key:		= off,	= on,
			Press								F = flash once
						C
					INPUTS
1	2	3	4	5	6	7	8	9	10	11	12

Press

B

AUDIO

CONTROL				I/O

1 2

3

4

5

6

7

8

OUTPUTS

ENTER PRESET VIEW ESC

VIDEO AUDIO

	C	C	Press	F
3	4	8

ESC

A

Figure 3-5 — Example 3: Selecting audio and selecting input 5

DPress and release the output 4 button (figure 3-6). The output 4 LED turns off, while the output 3 and output 8 LEDs remain lit.

5

LED key: = off, = on

1 2 3

1

2

3

3

		INPUTS								AUDIO
4	5	6	7	8	9	10	11	12		AUDIO
									CONTROL	I/O
4	5	6	7	8					ENTER PRESET VIEW ESC	VIDEO AUDIO
OUTPUTS
	Press			8					Press
									Press
	D
	D								E
4									ENTER

Figure 3-6 — Example 3d: Removing an audio tie

EPress and release the Enter button. The input and output LEDs turn off. The current configuration is now video input 5 tied to video output 1, output 3, output 4, and output 8; and audio input 5 tied to audio output 3 and output 8.

Viewing a configuration

The current configuration can be viewed using the front panel buttons. The view-only mode prevents inadvertent changes to the current configuration on a 12x8 Matrix 50 switcher with audio. View-only mode also provides a way to mute video and audio outputs (see Muting and unmuting video and/or audio in this chapter.

To view the current configuration, do the following:

1. Press the Esc button to clear any input LEDs, output LEDs, or control LEDs that may be on.

Matrix 50 Series Switchers • Operation

3-7

Image 27

Contents Matrix 50 Series Matrix Audio/Video SwitchersInstrucciones de seguridad Español Safety Instructions EnglishConsignes de Sécurité Français Sicherheitsanleitungen DeutschQS-1 Quick Start Matrix 50 Series SwitchersQuick Start Matrix 50 Series Switchers, cont’d Table of Contents Table of Contents, cont’d Matrix 50 Series Switchers Table of Contents Iii Iv Matrix 50 Series Switchers Table of Contents One About the Matrix 50 Series Switchers Matrix 50 Series Switchers IntroductionIntroductiontroduction, cont’d Matrix FeaturesIntroduction, cont’d Matrix 50 switcherMatrix 50 Series Switchers Introduction Introduction, cont’d Two Cabling and Rear Panel Views Installationstallation, cont’dRack Mounting the Switcher Matrix 50 Series Switchers InstallationPower connection Video input and output connections video models onlyAudio input and output connections audio models only RS-232/422 connection Installation, cont’dSimple external sync connection example External sync connectionMultiple device external sync connection example Additional rear panel viewsThree Input buttons, output buttons, and LEDs Front Panel Controls and IndicatorsOperationeration, cont’d DefinitionsControls Front Panel Operations PowerCreating a configuration Operation, cont’dExample 1 Creating a tie Example 1 Creating a set of video and audio tiesExample 3 Removing a tie from a set of video and audio ties Example 2 Adding a tie to a set of video and audio tiesExample 3 Selecting audio and selecting input Viewing a configurationExample 4 Viewing the current configuration Example 4e Viewing the current configuration, audio only Example 5 Muting and unmuting an output Muting and unmuting video and/or audio11 Example 5, step d Muting and unmuting outputs Using global memory presetsExample 7 Recalling a preset Example 6 Saving a presetExample 8 Viewing and adjusting an audio level Viewing and adjusting the audio level14 Example 8 Viewing the audio level Executive mode front panel security lockoutWorksheets TroubleshootingSystem reset to factory defaults Plasma display S-video problem16 Worksheet example 1 System equipment Worksheet example 1 System equipment17 Worksheet example 2 Daily configuration Worksheet example 2 Daily configuration18 Worksheet example 3 Test configuration Worksheet example 3 Test configurationConfiguration worksheet Operation, cont’d Four Programmer’ser’sGuide,Guidecont’d Host-to-Switcher InstructionsSwitcher-Initiated Messages Matrix 50 Series Switchers Programmer’s GuideUsing the Command/Response Table Switcher Error ResponsesCommand/Response Table Command Ascii Command Response Additional descriptionProgrammer’s Guide, cont’d Command/response table for SIS commands Cont’d View ties, gain, and presets Five MatrixSoftware,cont’d Matrix Switcher+ Control ProgramInstalling the software Using the softwareWindows buttons Extron Matrix Switcher+ Control Program window blankWindows menus Matrix Software, cont’dUsing emulation mode Using the help systemButton-Label Generator Extron’s Button-Label Generator window AAppendix a Matrix 50 Series Switchers Specifications Specificationsecifications, cont’dAudio input Matrix 50 Option Kits Specifications, cont’dMatrix 50 Series switchers part numbers Part NumbersCables Optional AccessoriesPre-cut cables Extron Part BNC-4 Mini HR CableVideo Cable AppendixBB ReferenceInformation,co t’d Hardware ProceduresOpening the switcher Matrix 50 Series Switchers Reference InformationFigure B-2 Side view, Matrix 50 S-video and audio switcher Closing the switcherReference Information, cont’d Installing a video moduleRemoving a video module Removing a video module on page B-5 Installing an audio moduleRemoving an audio module On page B-3Swapping the serial ports Figure B-8 Key and pin 1 mark Installing a firmware updateReplacing the AC fuse Setting the front panel jumperButton Labels Matrix 50 Series Switchers Reference Information B-11Blank Figure B-10 Button label blanks, 12-button strip Matrix 50 Series Switchers Reference Information B-13Reference Information, cont’d FCC Class a Notice Extron’s Warranty Extron Electronics, USA