Extron electronic manual Button Labels, Matrix 50 Series Switchers Reference Information B-11

Page 69

JMP9

JMP8

JMP7

JMP6

		Switcher type	Matrix size	JMP2 JMP3 JMP4 JMP5 JMP6 JMP7 JMP8							JMP9

			8 x 4	X X O O O O X O
			8 x 8	O X X O O O X O
		Video only	12 x 4	O	X	O	O	O	O	X	O
			12 x 8	X O X O O O X O

			8 x 4	O O X X O O X O
		Video &	8 x 8	X O O X O O X O
		Video &
		audio	12 x 4	X	X	O	X	O	O	X	O
	JMP5		12 x 8	O O O X O O X O
	JMP4		12 x 8	O O O X O O X O

			8 x 4	O X O O X O X O
	JMP3		8 x 4	O X O O X O X O
	JMP3
	JMP2		8 x 8	X O O O X O X O
	JMP2
		Audio only	12 x 4	O O O O X O X O
		Audio only
			12 x 8	X X X X O O X O
				X = jumper installed, O = jumper removed

Figure B-9 — Jumper settings, Matrix 50 series switchers

If you choose to check for proper operation before putting the cover back on, ensure that tools and hands are outside the switcher and then perform step 4. After recognizing the new configuration, the switcher should power up normally. Unplug the AC power cord, and reinstall the switcher.

4.Reinitialize the switcher to recognize the new configuration as follows: a. Connect the power cord to the AC power source.

b. Press and hold the Enter button while you connect the power cord to the switcher.

c. Observe that the Input, Output, Preset, View, and Esc LEDs all flash.

	d. Release the Enter button.
5.	Ensure that the switcher is working properly.

6.If the switcher was removed from a rack, remove its power cord, reattach the switcher to the rack, and reconnect the power cord.

7.	Reconnect the input and output cables.

Button Labels

Figure B-10 provides blanks of a 12-button strip of button labels. Feel free to photocopy them or cut them out of the manual, write button information in each button area as desired, and put them in the switcher’s label window. For 8-button strips and 4-button strips, use scissors to trim the blank to the appropriate length.

Matrix 50 Series Switchers • Reference Information B-11

Image 69

Contents Matrix 50 Series Matrix Audio/Video SwitchersConsignes de Sécurité Français Safety Instructions EnglishSicherheitsanleitungen Deutsch Instrucciones de seguridad EspañolQS-1 Quick Start Matrix 50 Series SwitchersQuick Start Matrix 50 Series Switchers, cont’d Table of Contents Table of Contents, cont’d Matrix 50 Series Switchers Table of Contents Iii Iv Matrix 50 Series Switchers Table of Contents One About the Matrix 50 Series Switchers Matrix 50 Series Switchers IntroductionIntroductiontroduction, cont’d Matrix FeaturesIntroduction, cont’d Matrix 50 switcherMatrix 50 Series Switchers Introduction Introduction, cont’d Two Rack Mounting the Switcher Installationstallation, cont’dMatrix 50 Series Switchers Installation Cabling and Rear Panel ViewsPower connection Video input and output connections video models onlyAudio input and output connections audio models only RS-232/422 connection Installation, cont’dSimple external sync connection example External sync connectionMultiple device external sync connection example Additional rear panel viewsThree Operationeration, cont’d Front Panel Controls and IndicatorsDefinitions Input buttons, output buttons, and LEDsControls Creating a configuration PowerOperation, cont’d Front Panel OperationsExample 1 Creating a tie Example 1 Creating a set of video and audio tiesExample 3 Removing a tie from a set of video and audio ties Example 2 Adding a tie to a set of video and audio tiesExample 3 Selecting audio and selecting input Viewing a configurationExample 4 Viewing the current configuration Example 4e Viewing the current configuration, audio only Example 5 Muting and unmuting an output Muting and unmuting video and/or audio11 Example 5, step d Muting and unmuting outputs Using global memory presetsExample 7 Recalling a preset Example 6 Saving a presetExample 8 Viewing and adjusting an audio level Viewing and adjusting the audio level14 Example 8 Viewing the audio level Executive mode front panel security lockoutSystem reset to factory defaults TroubleshootingPlasma display S-video problem Worksheets16 Worksheet example 1 System equipment Worksheet example 1 System equipment17 Worksheet example 2 Daily configuration Worksheet example 2 Daily configuration18 Worksheet example 3 Test configuration Worksheet example 3 Test configurationConfiguration worksheet Operation, cont’d Four Switcher-Initiated Messages Host-to-Switcher InstructionsMatrix 50 Series Switchers Programmer’s Guide Programmer’ser’sGuide,Guidecont’dUsing the Command/Response Table Switcher Error ResponsesCommand/Response Table Command Ascii Command Response Additional descriptionProgrammer’s Guide, cont’d Command/response table for SIS commands Cont’d View ties, gain, and presets Five Installing the software Matrix Switcher+ Control ProgramUsing the software MatrixSoftware,cont’dWindows buttons Extron Matrix Switcher+ Control Program window blankWindows menus Matrix Software, cont’dUsing emulation mode Using the help systemButton-Label Generator Extron’s Button-Label Generator window AAppendix a Matrix 50 Series Switchers Specifications Specificationsecifications, cont’dAudio input Matrix 50 Series switchers part numbers Specifications, cont’dPart Numbers Matrix 50 Option KitsCables Optional AccessoriesPre-cut cables Extron Part BNC-4 Mini HR CableVideo Cable AppendixBB Opening the switcher Hardware ProceduresMatrix 50 Series Switchers Reference Information ReferenceInformation,co t’dFigure B-2 Side view, Matrix 50 S-video and audio switcher Closing the switcherReference Information, cont’d Installing a video moduleRemoving a video module Removing a video module on page B-5 Installing an audio moduleRemoving an audio module On page B-3Swapping the serial ports Figure B-8 Key and pin 1 mark Installing a firmware updateReplacing the AC fuse Setting the front panel jumperButton Labels Matrix 50 Series Switchers Reference Information B-11Blank Figure B-10 Button label blanks, 12-button strip Matrix 50 Series Switchers Reference Information B-13Reference Information, cont’d FCC Class a Notice Extron’s Warranty Extron Electronics, USA