Extron electronic 50 manual Worksheet example 3 Test configuration

Page 38

Operation, cont’d

Worksheet example 3: Test configuration

The A/V system in this fictional organization needs to be fine tuned on a regular basis. Figure 3-18 shows a typical test configuration, with an Extron video test generator (input 12) generating a test pattern to all monitors (outputs 1, 2, 3, 4, and 6). Sound checks are run from the CD player (input 5) to all audio systems (outputs 3, 4, 6, and 8).

	Camera	Security	Lobby	Podium
	main	camera	security
				mic
	podium	#2	camera

	1	2	3	4

		Input sources
Audio		Class		Class		Class		Class
		Class		Class		Class		Class
		room #1		room #2		room #1		room #2
CD		room #1		room #2		room #1		room #2
CD		VCR		VCR		LD		LD
		VCR		VCR		LD		LD
5	6		7		8		9		10	11

VTG

200

12

1

2

3

4

5

6

7

Main

Lobby

Class

Class

Archive

Main

hall

room #1

room #2

VCR

podium

monitor

monitor

rear proj

rear proj

monitor

Output destinations

Preset #

12

Title: Test configuration

Video:

Audio:

8

Lunch

room

stereo

Fill in the preset number, use colors or dashes, etc. to make connecting lines. Indicate if the configuration is for Video, Audio, or both.

Figure 3-18 — Worksheet example 3: Test configuration

3-18 Matrix 50 Series Switchers • Operation

Image 38

Contents Matrix Audio/Video Switchers Matrix 50 SeriesSicherheitsanleitungen Deutsch Safety Instructions EnglishConsignes de Sécurité Français Instrucciones de seguridad EspañolQuick Start Matrix 50 Series Switchers QS-1Quick Start Matrix 50 Series Switchers, cont’d Table of Contents Table of Contents, cont’d Matrix 50 Series Switchers Table of Contents Iii Iv Matrix 50 Series Switchers Table of Contents One Introductiontroduction, cont’d About the Matrix 50 Series SwitchersMatrix 50 Series Switchers Introduction Features MatrixMatrix 50 switcher Introduction, cont’dMatrix 50 Series Switchers Introduction Introduction, cont’d Two Matrix 50 Series Switchers Installation Installationstallation, cont’dRack Mounting the Switcher Cabling and Rear Panel ViewsAudio input and output connections audio models only Power connectionVideo input and output connections video models only Installation, cont’d RS-232/422 connectionExternal sync connection Simple external sync connection exampleAdditional rear panel views Multiple device external sync connection exampleThree Definitions Front Panel Controls and IndicatorsOperationeration, cont’d Input buttons, output buttons, and LEDsControls Operation, cont’d PowerCreating a configuration Front Panel OperationsExample 1 Creating a set of video and audio ties Example 1 Creating a tieExample 2 Adding a tie to a set of video and audio ties Example 3 Removing a tie from a set of video and audio tiesViewing a configuration Example 3 Selecting audio and selecting inputExample 4 Viewing the current configuration Example 4e Viewing the current configuration, audio only Muting and unmuting video and/or audio Example 5 Muting and unmuting an outputUsing global memory presets 11 Example 5, step d Muting and unmuting outputsExample 6 Saving a preset Example 7 Recalling a presetViewing and adjusting the audio level Example 8 Viewing and adjusting an audio levelExecutive mode front panel security lockout 14 Example 8 Viewing the audio levelPlasma display S-video problem TroubleshootingSystem reset to factory defaults WorksheetsWorksheet example 1 System equipment 16 Worksheet example 1 System equipmentWorksheet example 2 Daily configuration 17 Worksheet example 2 Daily configurationWorksheet example 3 Test configuration 18 Worksheet example 3 Test configurationConfiguration worksheet Operation, cont’d Four Matrix 50 Series Switchers Programmer’s Guide Host-to-Switcher InstructionsSwitcher-Initiated Messages Programmer’ser’sGuide,Guidecont’dSwitcher Error Responses Using the Command/Response TableProgrammer’s Guide, cont’d Command/Response TableCommand Ascii Command Response Additional description Command/response table for SIS commands Cont’d View ties, gain, and presets Five Using the software Matrix Switcher+ Control ProgramInstalling the software MatrixSoftware,cont’dExtron Matrix Switcher+ Control Program window blank Windows buttonsMatrix Software, cont’d Windows menusButton-Label Generator Using emulation modeUsing the help system Extron’s Button-Label Generator window AAppendix a Specificationsecifications, cont’d Matrix 50 Series Switchers SpecificationsAudio input Part Numbers Specifications, cont’dMatrix 50 Series switchers part numbers Matrix 50 Option KitsOptional Accessories CablesVideo Cable Pre-cut cablesExtron Part BNC-4 Mini HR Cable AppendixBB Matrix 50 Series Switchers Reference Information Hardware ProceduresOpening the switcher ReferenceInformation,co t’dClosing the switcher Figure B-2 Side view, Matrix 50 S-video and audio switcherInstalling a video module Reference Information, cont’dRemoving a video module Installing an audio module Removing a video module on page B-5On page B-3 Removing an audio moduleSwapping the serial ports Installing a firmware update Figure B-8 Key and pin 1 markSetting the front panel jumper Replacing the AC fuseMatrix 50 Series Switchers Reference Information B-11 Button LabelsBlank Matrix 50 Series Switchers Reference Information B-13 Figure B-10 Button label blanks, 12-button stripReference Information, cont’d FCC Class a Notice Extron’s Warranty Extron Electronics, USA