Extron electronic 50 manual Optional Accessories, Cables

Page 57

Optional Accessories

Extron Part	Part #
Rack/desk mounting kit	70-077-03
Captive screw audio connector	10-319-10
SVHS - BNC adapter	26-353-01
RCA-to-BNC adapter	10-264-01
MKP 1000
Gray	60-239-01
Black	60-239-02
White	60-239-03
MKP 1000M (master)	60-298-01
MKP 1000S (slave)	60-298-02

Cables

When using signals with a scanning frequency of 15-125 kHz and running distances of 100 feet or more, use high resolution BNC cables to achieve maximum performance. Either BNC-4 Mini HR cable or BNC-5 Mini HR cable can be used for composite video.

Bulk cable

	Extron Part	Part #
	RG6 super high resolution cable
	RG6-1 bulk , 500’	22-098-02
	RG6-1 bulk , 1000’	22-098-03
	RG6-4 bulk , 500’	22-099-02
	RG6-5 bulk , 500’	22-100-02
	RG6 male crimp connectors, qty. 50	100-075-51

	BNC-2 Mini HR Cable
	BNC-2 Mini HR bulk, 250’	22-123-02
	BNC-2 Mini HR bulk, 500’	22-123-03

	BNC-4 Mini HR Cable
	BNC-4 Mini HR bulk, 500’	22-032-02
	BNC-4 Mini HR bulk, 1000’	22-032-03

	BNC-5 Mini HR Cable
	BNC-5 Mini HR bulk, 500’	22-020-02
	BNC-5 Mini HR bulk, 1000’	22-020-03

	Plenum BNC-5 Mini HR Cable
	Plenum BNC-5 Mini HR bulk, 500’	22-103-02
	Plenum BNC-5 Mini HR bulk, 1000’	22-103-03
Assorted connectors
	Extron Part	Part #
	BNC connectors
	BNC Mini HR crimp connectors, qty. 50	100-074-51
	RG6 male crimp connectors, qty. 50	100-075-51
	BNC bulkhead connectors, qty. 50
	(for custom wall plates)	100-076-51

Matrix 50 Series Switchers • Specifications

A-5

Image 57

Contents Matrix 50 Series Matrix Audio/Video SwitchersConsignes de Sécurité Français Safety Instructions EnglishSicherheitsanleitungen Deutsch Instrucciones de seguridad EspañolQS-1 Quick Start Matrix 50 Series SwitchersQuick Start Matrix 50 Series Switchers, cont’d Table of Contents Table of Contents, cont’d Matrix 50 Series Switchers Table of Contents Iii Iv Matrix 50 Series Switchers Table of Contents One About the Matrix 50 Series Switchers Matrix 50 Series Switchers IntroductionIntroductiontroduction, cont’d Matrix FeaturesIntroduction, cont’d Matrix 50 switcherMatrix 50 Series Switchers Introduction Introduction, cont’d Two Rack Mounting the Switcher Installationstallation, cont’dMatrix 50 Series Switchers Installation Cabling and Rear Panel ViewsPower connection Video input and output connections video models onlyAudio input and output connections audio models only RS-232/422 connection Installation, cont’dSimple external sync connection example External sync connectionMultiple device external sync connection example Additional rear panel viewsThree Operationeration, cont’d Front Panel Controls and IndicatorsDefinitions Input buttons, output buttons, and LEDsControls Creating a configuration PowerOperation, cont’d Front Panel OperationsExample 1 Creating a tie Example 1 Creating a set of video and audio tiesExample 3 Removing a tie from a set of video and audio ties Example 2 Adding a tie to a set of video and audio tiesExample 3 Selecting audio and selecting input Viewing a configurationExample 4 Viewing the current configuration Example 4e Viewing the current configuration, audio only Example 5 Muting and unmuting an output Muting and unmuting video and/or audio11 Example 5, step d Muting and unmuting outputs Using global memory presetsExample 7 Recalling a preset Example 6 Saving a presetExample 8 Viewing and adjusting an audio level Viewing and adjusting the audio level14 Example 8 Viewing the audio level Executive mode front panel security lockoutSystem reset to factory defaults TroubleshootingPlasma display S-video problem Worksheets16 Worksheet example 1 System equipment Worksheet example 1 System equipment17 Worksheet example 2 Daily configuration Worksheet example 2 Daily configuration18 Worksheet example 3 Test configuration Worksheet example 3 Test configurationConfiguration worksheet Operation, cont’d Four Switcher-Initiated Messages Host-to-Switcher InstructionsMatrix 50 Series Switchers Programmer’s Guide Programmer’ser’sGuide,Guidecont’dUsing the Command/Response Table Switcher Error ResponsesCommand/Response Table Command Ascii Command Response Additional descriptionProgrammer’s Guide, cont’d Command/response table for SIS commands Cont’d View ties, gain, and presets Five Installing the software Matrix Switcher+ Control ProgramUsing the software MatrixSoftware,cont’dWindows buttons Extron Matrix Switcher+ Control Program window blankWindows menus Matrix Software, cont’dUsing emulation mode Using the help systemButton-Label Generator Extron’s Button-Label Generator window AAppendix a Matrix 50 Series Switchers Specifications Specificationsecifications, cont’dAudio input Matrix 50 Series switchers part numbers Specifications, cont’dPart Numbers Matrix 50 Option KitsCables Optional AccessoriesPre-cut cables Extron Part BNC-4 Mini HR CableVideo Cable AppendixBB Opening the switcher Hardware ProceduresMatrix 50 Series Switchers Reference Information ReferenceInformation,co t’dFigure B-2 Side view, Matrix 50 S-video and audio switcher Closing the switcherReference Information, cont’d Installing a video moduleRemoving a video module Removing a video module on page B-5 Installing an audio moduleRemoving an audio module On page B-3Swapping the serial ports Figure B-8 Key and pin 1 mark Installing a firmware updateReplacing the AC fuse Setting the front panel jumperButton Labels Matrix 50 Series Switchers Reference Information B-11Blank Figure B-10 Button label blanks, 12-button strip Matrix 50 Series Switchers Reference Information B-13Reference Information, cont’d FCC Class a Notice Extron’s Warranty Extron Electronics, USA