Extron electronic 50 Example 1 Creating a set of video and audio ties, Example 1 Creating a tie

Page 25

2.Select to configure video, audio, or both by pressing the Video and/or Audio buttons.

3.Select the desired input and output(s) by pressing the input and output buttons.

4.	Press and release the Enter button.
5.	Repeat steps 1 through 4 to create additional ties until the desired
	configuration is complete.

1. Only one video input and one audio input can be tied to an output.

2.If a tie is made between an input and an output, and the selected output was previously tied to another input, the older tie is broken in favor of the newer tie.

3.To indicate current ties, output LEDs light when an input is selected. To clear unwanted outputs, press and release the associated output buttons.

4.If, when you configure video and audio ties, the Audio LED blinks and the Video LED is on after you select an input or output, the LEDs indicate audio breakaway, meaning that the audio ties are not the same as the video ties for that input.

5.If an input with no tie is selected, only that input’s LED lights.

6.When the Video and Audio LEDs are on, if an input with an audio tie but no video tie is selected, the input’s LED lights and the Audio LED blinks.

7.As each output is selected, the associated output LED blinks to indicate a tentative tie. LEDs for output(s) that were already tied to the input light steadily. Outputs that are already tied can be left on, along with new blinking selections, or toggled off by pressing the associated output button.

Example 1: Creating a set of video and audio ties

See figure 3-3 and the following steps for an example in which input 5 is tied to outputs 3, 4, and 8 on a 12x8 Matrix 50 switcher with audio.

This example assumes that there are no ties in the current configuration.

5

LED key:

= off,

= on, B = blinking,

Press

Press

Press

F

= flash once

B

C

VIDEO

AUDIO

INPUTS

1

2

3

4

5

6

7

8

9

10

11

12

CONTROL

I/O

1

2

3

4

5

6

7

8

ENTER PRESET VIEW

ESC

VIDEO

AUDIO

OUTPUTS

Press

B

Press

B

B

Press

Press

F Press

		D	E
3	4	8	ENTER

A

ESC

Figure 3-3 — Example 1: Creating a tie

APress and release the Esc button. The Esc LED flashes once.

BTo select video and audio for the tie, if necessary, press and release the Video and Audio buttons until the Video and Audio LEDs light.

Matrix 50 Series Switchers • Operation

3-5

Image 25

Contents Matrix 50 Series Matrix Audio/Video SwitchersConsignes de Sécurité Français Safety Instructions EnglishSicherheitsanleitungen Deutsch Instrucciones de seguridad EspañolQS-1 Quick Start Matrix 50 Series SwitchersQuick Start Matrix 50 Series Switchers, cont’d Table of Contents Table of Contents, cont’d Matrix 50 Series Switchers Table of Contents Iii Iv Matrix 50 Series Switchers Table of Contents One Matrix 50 Series Switchers Introduction About the Matrix 50 Series SwitchersIntroductiontroduction, cont’d Matrix FeaturesIntroduction, cont’d Matrix 50 switcherMatrix 50 Series Switchers Introduction Introduction, cont’d Two Rack Mounting the Switcher Installationstallation, cont’dMatrix 50 Series Switchers Installation Cabling and Rear Panel ViewsVideo input and output connections video models only Power connectionAudio input and output connections audio models only RS-232/422 connection Installation, cont’dSimple external sync connection example External sync connectionMultiple device external sync connection example Additional rear panel viewsThree Operationeration, cont’d Front Panel Controls and IndicatorsDefinitions Input buttons, output buttons, and LEDsControls Creating a configuration PowerOperation, cont’d Front Panel OperationsExample 1 Creating a tie Example 1 Creating a set of video and audio tiesExample 3 Removing a tie from a set of video and audio ties Example 2 Adding a tie to a set of video and audio tiesExample 3 Selecting audio and selecting input Viewing a configurationExample 4 Viewing the current configuration Example 4e Viewing the current configuration, audio only Example 5 Muting and unmuting an output Muting and unmuting video and/or audio11 Example 5, step d Muting and unmuting outputs Using global memory presetsExample 7 Recalling a preset Example 6 Saving a presetExample 8 Viewing and adjusting an audio level Viewing and adjusting the audio level14 Example 8 Viewing the audio level Executive mode front panel security lockoutSystem reset to factory defaults TroubleshootingPlasma display S-video problem Worksheets16 Worksheet example 1 System equipment Worksheet example 1 System equipment17 Worksheet example 2 Daily configuration Worksheet example 2 Daily configuration18 Worksheet example 3 Test configuration Worksheet example 3 Test configurationConfiguration worksheet Operation, cont’d Four Switcher-Initiated Messages Host-to-Switcher InstructionsMatrix 50 Series Switchers Programmer’s Guide Programmer’ser’sGuide,Guidecont’dUsing the Command/Response Table Switcher Error ResponsesCommand Ascii Command Response Additional description Command/Response TableProgrammer’s Guide, cont’d Command/response table for SIS commands Cont’d View ties, gain, and presets Five Installing the software Matrix Switcher+ Control ProgramUsing the software MatrixSoftware,cont’dWindows buttons Extron Matrix Switcher+ Control Program window blankWindows menus Matrix Software, cont’dUsing the help system Using emulation modeButton-Label Generator Extron’s Button-Label Generator window AAppendix a Matrix 50 Series Switchers Specifications Specificationsecifications, cont’dAudio input Matrix 50 Series switchers part numbers Specifications, cont’dPart Numbers Matrix 50 Option KitsCables Optional AccessoriesExtron Part BNC-4 Mini HR Cable Pre-cut cablesVideo Cable AppendixBB Opening the switcher Hardware ProceduresMatrix 50 Series Switchers Reference Information ReferenceInformation,co t’dFigure B-2 Side view, Matrix 50 S-video and audio switcher Closing the switcherReference Information, cont’d Installing a video moduleRemoving a video module Removing a video module on page B-5 Installing an audio moduleRemoving an audio module On page B-3Swapping the serial ports Figure B-8 Key and pin 1 mark Installing a firmware updateReplacing the AC fuse Setting the front panel jumperButton Labels Matrix 50 Series Switchers Reference Information B-11Blank Figure B-10 Button label blanks, 12-button strip Matrix 50 Series Switchers Reference Information B-13Reference Information, cont’d FCC Class a Notice Extron’s Warranty Extron Electronics, USA