ATTO Technology VT-Class manual Appendix E Specifications, Environmental and physical

Page 93

Appendix E Specifications

Environmental and physical

•Humidity: 10-85% non-condensing

•Normal operating temperature at sea level: 5- 40o C

•Storage temperature: -25-60oC

•AC input voltage 100-240V rated

•50/60 Hz

Rack Mount Dimensions

•Height: 131mm (5.16”) 3U

•Width: 447mm (17.60”)

•Depth: 585mm (23.03”)

•Approximately 39 kg (86 pounds) fully loaded with 24 drives

Floor Mount Dimensions

•Height: 524mm (20.62”) 3U

•Width: 137mm (5.39”)

•Depth: 595mm (23.42”)

•Approximately 42 kg (92 pounds) fully loaded with 24 drives

A-xii Appendix

Image 93

Contents Diamond Storage Array VT-Class Page Page Contents ExpressNAV Pages Atto ExpressNAV Browser-based InterfaceSerial Port Configuration Commands Fibre Channel Configuration CommandsMaintenance Services Commands Diagnostic CommandsECC Drive Management CommandsDiagnostics, Upgrade and Maintenance Troubleshooting Configuring the Diamond-VTResetting Defaults Virtual TapeAppendix E Specifications Xii Appendix D Sample Zoning Command SequencesAppendix F Product Safety Xiii Appendix G Part numbers Xiv Appendix H WarrantyPreface DisclaimerAtto Technology, Inc Page Diamond Storage Array-VT Product Overview Diamond-VT featuresScsi model Fibre Channel modelRS-232 Diamond-VT Technical OverviewEthernet 400MB/secATA Interface Engine AIE The interface to each Adxt Powers ATA to New LevelsPhysical setup Installation InstructionsSet up the Ethernet connection Connect to EthernetConfiguration examples Set up Virtual Tape configurationConnect to Ethernet, on page 5, follow RAID Level 10 with Hot Spare sledsFloor model Diamond-VT ComponentsRack mount model Diamond-VT Physical Setup Floor ModelRack Mount Physical setup Connecting a Fibre Channel Array AutoconfigurationManual configuration Fibre Channel connections To connect the Scsi Diamond-VT Connecting a Scsi ArrayBus speed, MB/sec Bus width Max. bus lengths Max. device BitsScsi connections Command Line Interface Accessing the Diamond-VTAtto ExpressNAV RS-232 portSnmp In-band CLI Over Fibre Channel DetailsInitiator Host Diamond-VT Initiator/Host Diamond-VT Serial Port Access Serial port access To connect to the Ethernet port Ethernet Access Telnet and Snmp ProtocolsTo use Telnet To use SnmpTraps are generated for the following situations Atto ExpressNAV Browser-based Interface Navigating ExpressNAVBrowser compatibility Parameter name Submit button Reset buttonExpressNAV Pages Configuration Tape VolumesLogical Units PartitionsCLI Interface via ASCII-based Commands SaveConfiguration commandReady Hostname Return type/mode Return format/contentCommand Defaults Example Summary of CLI CommandsCLI index Zoneaddhost zone1 General Use Commands Ethernet Commands TelnetPassword SNMPUpdatesTelnetTimeout SNMPTrapsFibre Channel Configuration Commands FcPortName FcPortListFcScsiBusyStatus FcWWNameSerialPortBaudRate Serial Port Configuration CommandsSerialPortHandshake SerialPortEchoMaintenance Services Commands Diagnostic Commands SledFaultLED PowerAudibleAlarmTapeVolumeInfo RAID5ClearDataStatusDrive Management Commands LUNState DriveWipeIdeTransferRate IdeWriteCacheRAIDInterleave RAID5ClearDataRAIDHaltRebuild RAIDManualRebuildTapeVolumeBlockSize RestoreModePagesRebuildPriority TapeWriteProtectZoneCreate ZoneClearAllZoneDelete ZoneRemoveDeviceCLI configure drives Virtual Tape Volumes Configuring the Diamond-VTRAID Level Hot Spare sledsEnhancing performance InterleaveVirtual Tape Optional Hot Spare Sled To set up RAID Level 10 with Hot Spare sledsZones Planned configuration is a work-in-processPrinciples of Zoning Device portion defines the LUNsFactors to consider Status and Sense DataType ZoneInfo To create a zone Configuring ZoningTo remove zones To change current zonesZone definition tables The Zone commands ErrorsUpdating Firmware Updating firmware via the RS-232 serial portUpdating firmware via the optional Ethernet card Type put ....ima Cd c\diamond\flashPower On Self Test Post Each time Diagnostics, Upgrade and MaintenanceRS-232 Monitoring Port and CLI One tool to Ethernet Monitoring Port and CLI If the optionalPower Supply Monitoring The Diamond-VT System Fault LED and Error Codes If a serious25C 32C 35C 40C Disk Drive Activity and Disk Fault LEDs Each Monitoring, reporting Windows 2000 special instructions Error Messages TroubleshootingCommand Line Interface messages Specific situations and suggestionsIf you can’t access the Diamond-VT CLI via Ethernet If a power supply failsIf you cannot read or write to the Diamond-VT Type FirmwareRestart in CLIFactory Default Resetting DefaultsDefault Return to Default settingsCommand Default Rebuilding RAID Level 5 and 10 Configurations To synchronize mirrored drives manually Hardware Maintenance Hardware maintenance Disk Drives Hot Swap Operating InstructionsPower Supplies To replace a blower assemblyBlower Assemblies Fibre Channel technology Appendix a GlossarySAN technology Scsi protocolAppendix Feature Appendix B ATA Disk TechnologyFibre Channel Appendix C LunInfo for a Jbod setup PartitionInfo active 59 LunInfoZoneInfo TapeVolumeInfoViii First time configuration after download Appendix D Sample Zoning Command SequencesSimple configuration Symmetric ModelZoneClearAll ZoneCreate zone1 Asymmetric ModelZoneAddPort zone1 ZoneCreate zone2 ZoneAddPort zone2 ZoneCreate zone3Combined Symmetric/Asymmetric Model Rack Mount Dimensions Appendix E SpecificationsFloor Mount Dimensions Environmental and physicalSafety compliances Appendix F Product SafetyEMC specifications Radio and television interferenceDescription All models Appendix G Part numbersAppendix H Warranty Manufacturer limited warrantyContact Atto Technology, Inc