ATTO Technology VT-Class PowerAudibleAlarm, RAID5ClearDataStatus, RAIDRebuildStatus, SerialNumber

Page 51

PowerAudibleAlarm

Silences the audible alarm for a current power supply failure. The alarm will be activated on the next power failure.

Immediate command: PowerAudibleAlarm disabled

RAID5ClearDataStatus

Displays the status of RAID5 Clear Data processing. S represents the sled number, D represents the drive number. Applies to RAID5 only

Set syntax: RAID5ClearDataStatus

RAIDRebuildStatus

Displays the RAID1, RAID 5 or RAID 10 Rebuild Status Summary. If no RAID groups are defined, the header information is displayed with no data. The status summary contains the RAID1, RAID 5 or RAID 10.The RAIDRebuildStatus command has no effect on the state of any rebuild in progress.

Member index and the following fields in tabular form:

•Status : OK, DEGRADED, IN PROGRESS, or

FAULTED

•Sled Number : Location of the sled

•Current LBA: Logical block currently being rebuilt

•Maximum LBA: Last logical block to be rebuilt

•Status OK: the RAID1 Mirror is in sync and no rebuild activity is occurring. The Current LBA, Maximum LBA and percentage complete values are not displayed.

•Status Degraded: the RAID1 Mirror is out of sync and is waiting to be rebuilt.

•Status In Progress: the RAID1 Mirror is out of sync and a rebuild is occurring on the respective drive.

•Status Faulted: the RAID1 Mirror is out of sync and an error occurred in an attempt to synchronize the drives in the RAID 1 group.

SerialNumber

View the board serial number, a 10-character field. The first four alphanumeric characters are an abbreviation representing the product name. The remaining six digits are the individual unit’s number.

Get syntax: get SerialNumber

SledFaultLED

Changes the state of the selected sled LED to the indicated state. Choose the sled number, 1-12,or all, turn on or off

Default: off

Set syntax: set SledFaultLED [ all 1 2 3 4 5 6 7 8 9 10 11 12] [ on off]

SMARTData

Displays the current SMART (Self-Monitoring Analysis and Reporting Technology) data for the specified drive.

Immediate command: SMARTData [sled#] [drive #]

TapeDriveInfo

Displays information about the named Tape Drive including LUN, Tape Volume ID and state of the tape drive.

Get syntax: TapeDriveInfo [tape drive #]

TapeVolumeInfo

Displays information about the named Tape Volume including Volume ID, LUN, Virtual Disk ID, Partition ID, Total capacity and percentage of capacity used.

Get syntax: TapeVolumeInfo [tape volume #]

Temperature

Returns the current internal temperature of this Diamond Storage Array in degrees Celsius. The value is read only.

Get syntax: get Temperature

VirtualDriveInfo

Displays the named Virtual Drive definitions.

Get syntax: VirtualDriveInfo [activeplanned] [Virtual Drive ID]

ZoneInfo

Displays the named zones’ definitions. Information about the Active Zone Configuration is the default; if you want information about the Planned Zone Configuration, type ZoneInfo Planned zone_name.

Zone syntax: ZoneInfo [Planned] [zone_name] [all]

ZoneState

Changes the specific state of a zone. The ZoneState command must be entered as enabled to activate the zone before using the ZoneCommit command (which makes the Planned Zone Configuration the Active configuration).

Default: disabled

Set syntax: ZoneState zone_name [enableddisabled]

Get syntax: ZoneInfo

40 CLI: diagnostics

Page 50 Page 52
Image 51
Page 50 Page 52
Contents Diamond Storage Array VT-Class Page Page Contents ExpressNAV Pages Atto ExpressNAV Browser-based InterfaceDiagnostic Commands Fibre Channel Configuration CommandsSerial Port Configuration Commands Maintenance Services CommandsECC Drive Management CommandsVirtual Tape Configuring the Diamond-VTDiagnostics, Upgrade and Maintenance Troubleshooting Resetting DefaultsAppendix G Part numbers Xiv Appendix H Warranty Appendix D Sample Zoning Command SequencesAppendix E Specifications Xii Appendix F Product Safety XiiiPreface DisclaimerAtto Technology, Inc Page Diamond Storage Array-VT Product Overview Diamond-VT featuresScsi model Fibre Channel model400MB/sec Diamond-VT Technical OverviewRS-232 EthernetATA Interface Engine AIE The interface to each Adxt Powers ATA to New LevelsConnect to Ethernet Installation InstructionsPhysical setup Set up the Ethernet connectionRAID Level 10 with Hot Spare sleds Set up Virtual Tape configurationConfiguration examples Connect to Ethernet, on page 5, followFloor model Diamond-VT ComponentsRack mount model Diamond-VT Physical Setup Floor ModelRack Mount Physical setup Connecting a Fibre Channel Array AutoconfigurationManual configuration Fibre Channel connections Bits Connecting a Scsi ArrayTo connect the Scsi Diamond-VT Bus speed, MB/sec Bus width Max. bus lengths Max. deviceScsi connections RS-232 port Accessing the Diamond-VTCommand Line Interface Atto ExpressNAVSnmp In-band CLI Over Fibre Channel DetailsInitiator Host Diamond-VT Initiator/Host Diamond-VT Serial Port Access Serial port access To use Snmp Ethernet Access Telnet and Snmp ProtocolsTo connect to the Ethernet port To use TelnetTraps are generated for the following situations Atto ExpressNAV Browser-based Interface Navigating ExpressNAVBrowser compatibility Parameter name Submit button Reset buttonExpressNAV Pages Partitions Tape VolumesConfiguration Logical UnitsCLI Interface via ASCII-based Commands SaveConfiguration commandReady Hostname Return type/mode Return format/contentCommand Defaults Example Summary of CLI CommandsCLI index Zoneaddhost zone1 General Use Commands Ethernet Commands SNMPTraps SNMPUpdatesTelnetPassword TelnetTimeoutFibre Channel Configuration Commands FcWWName FcPortListFcPortName FcScsiBusyStatusSerialPortEcho Serial Port Configuration CommandsSerialPortBaudRate SerialPortHandshakeMaintenance Services Commands Diagnostic Commands RAID5ClearDataStatus PowerAudibleAlarmSledFaultLED TapeVolumeInfoDrive Management Commands IdeWriteCache DriveWipeLUNState IdeTransferRateRAIDManualRebuild RAID5ClearDataRAIDInterleave RAIDHaltRebuildTapeWriteProtect RestoreModePagesTapeVolumeBlockSize RebuildPriorityZoneRemoveDevice ZoneClearAllZoneCreate ZoneDeleteCLI configure drives Hot Spare sleds Configuring the Diamond-VTVirtual Tape Volumes RAID LevelEnhancing performance InterleaveVirtual Tape Optional Hot Spare Sled To set up RAID Level 10 with Hot Spare sledsDevice portion defines the LUNs Planned configuration is a work-in-processZones Principles of ZoningFactors to consider Status and Sense DataType ZoneInfo To change current zones Configuring ZoningTo create a zone To remove zonesZone definition tables The Zone commands ErrorsUpdating Firmware Updating firmware via the RS-232 serial portUpdating firmware via the optional Ethernet card Type put ....ima Cd c\diamond\flashEthernet Monitoring Port and CLI If the optional Diagnostics, Upgrade and MaintenancePower On Self Test Post Each time RS-232 Monitoring Port and CLI One tool toPower Supply Monitoring The Diamond-VT System Fault LED and Error Codes If a serious25C 32C 35C 40C Disk Drive Activity and Disk Fault LEDs Each Monitoring, reporting Specific situations and suggestions TroubleshootingWindows 2000 special instructions Error Messages Command Line Interface messagesType FirmwareRestart in CLI If a power supply failsIf you can’t access the Diamond-VT CLI via Ethernet If you cannot read or write to the Diamond-VTReturn to Default settings Resetting DefaultsFactory Default DefaultCommand Default Rebuilding RAID Level 5 and 10 Configurations To synchronize mirrored drives manually Hardware Maintenance Hardware maintenance Disk Drives Hot Swap Operating InstructionsPower Supplies To replace a blower assemblyBlower Assemblies Scsi protocol Appendix a GlossaryFibre Channel technology SAN technologyAppendix Feature Appendix B ATA Disk TechnologyFibre Channel Appendix C LunInfo for a Jbod setup PartitionInfo active 59 LunInfoZoneInfo TapeVolumeInfoViii Symmetric Model Appendix D Sample Zoning Command SequencesFirst time configuration after download Simple configurationZoneAddPort zone2 ZoneCreate zone3 Asymmetric ModelZoneClearAll ZoneCreate zone1 ZoneAddPort zone1 ZoneCreate zone2Combined Symmetric/Asymmetric Model Environmental and physical Appendix E SpecificationsRack Mount Dimensions Floor Mount DimensionsRadio and television interference Appendix F Product SafetySafety compliances EMC specificationsDescription All models Appendix G Part numbersAppendix H Warranty Manufacturer limited warrantyContact Atto Technology, Inc
Top Page Image Contents