ATTO Technology VT-Class manual Ethernet Commands

Page 44

6.3 Ethernet Commands

Ethernet configuration commands configure the Ethernet and TCP/IP parameters for the Diamond Storage Array with an optional Ethernet management services card.

EthernetSpeed

Specifies the speed of the Ethernet Network to which the Diamond Storage Array is connected. Choices are: [10100 Auto] where 10= 10 baseT, 100= 100 baseT

Default: auto

Set syntax: set EthernetSpeed [10 100 Auto]

Get syntax: get EthernetSpeed Requires a SaveConfiguration command Returns: [10 100 UNKNOWN]

If auto enabled, value in parentheses indicates current speed

IPDHCP

Selecting DHCP allow the Diamond Storage Array to request an IP address from the network. It requires that the Diamond be attached to a network with at least one DHCP server. The network must have at least one DHCP server.

Default: disabled

Set syntax: set IPDHCP [enabled disabled]

Get syntax: get IPDHCP

Requires a SaveConfiguration command

Exit

Exits the current Ethernet telnet CLI session; it has no effect if used during a serial or in-band CLI session.

Immediate command: Exit

FTPPassword

Specifies a password of up to 32 characters for an FTP session.

Default: diamond

Set syntax: set FTPPassword

Requires a SaveConfiguration Restart command

IPAddress

Specifies the IP Address of the Diamond Storage Array on the Ethernet network. If DHCP is enabled, the assigned address of the Diamond will be displayed. Setting this value always modifies the internal NVRAM value of the IP address.If IPDHCP is enabled (see below), get command reports current IP address assigned by DHCP server

Default IP Address: 10.0.0.1

Set syntax: set IPAddress xxx.xxx.xxx.xxx

Get syntax: get IPAddress

Requires a SaveConfiguration command

IPGateway

Specifies the IP Gateway for the Diamond Storage Array on the Ethernet network. If IPDHCP is enabled (see above), get command reports current IP gateway assigned by DHCP server. Must conform to xxx.xxx.xxx.xxx standard network IP addressing.

Default: 0.0.0.0

Set syntax: set IPGateway xxx.xxx.xxx.xxx

Get syntax: get IPGateway

Requires a SaveConfiguration command

IPSubnetMask

Specifies the IP Subnet Mask for the Diamond Storage Array on the Ethernet network. If DHCP is enabled, the assigned subnet mask for the unit will be displayed.

Setting this value always modifies the internal NVRAM value of the IP Subnet Mask.If IPDHCP is enabled (see above), get command reports current subnet mask assigned by DHCP server.

Default: 255.255.255.0

Set syntax: set IPSubnetMask xxx.xxx.xxx.xxx

Get syntax: get IPSubnetMask Requires a SaveConfiguration command

SNMPTrapAddress

Sets up IP trap address and trap level.

Default: 10.0.0.1

Set syntax: set SNMPTrapAddress [Index:1-6] [Address: xxx.xxx.xxx.xxx] Level: Critical Warning All None]...

Requires a SaveConfiguration Restart command Get syntax: get SNMPTrapAddress

33

ATTO Technology Inc.

Page 43 Page 45
Image 44
Page 43 Page 45
Contents Diamond Storage Array VT-Class Page Page Contents Atto ExpressNAV Browser-based Interface ExpressNAV PagesFibre Channel Configuration Commands Serial Port Configuration CommandsMaintenance Services Commands Diagnostic CommandsDrive Management Commands ECCConfiguring the Diamond-VT Diagnostics, Upgrade and Maintenance TroubleshootingResetting Defaults Virtual TapeAppendix D Sample Zoning Command Sequences Appendix E Specifications XiiAppendix F Product Safety Xiii Appendix G Part numbers Xiv Appendix H WarrantyAtto Technology, Inc PrefaceDisclaimer Page Diamond-VT features Diamond Storage Array-VT Product OverviewFibre Channel model Scsi modelDiamond-VT Technical Overview RS-232Ethernet 400MB/secAdxt Powers ATA to New Levels ATA Interface Engine AIE The interface to eachInstallation Instructions Physical setupSet up the Ethernet connection Connect to EthernetSet up Virtual Tape configuration Configuration examplesConnect to Ethernet, on page 5, follow RAID Level 10 with Hot Spare sledsDiamond-VT Components Floor modelRack mount model Rack Mount Diamond-VT Physical SetupFloor Model Physical setup Manual configuration Connecting a Fibre Channel ArrayAutoconfiguration Fibre Channel connections Connecting a Scsi Array To connect the Scsi Diamond-VTBus speed, MB/sec Bus width Max. bus lengths Max. device BitsScsi connections Accessing the Diamond-VT Command Line InterfaceAtto ExpressNAV RS-232 portSnmp Initiator Host Diamond-VT In-band CLI Over Fibre ChannelDetails Initiator/Host Diamond-VT Serial Port Access Serial port access Ethernet Access Telnet and Snmp Protocols To connect to the Ethernet portTo use Telnet To use SnmpTraps are generated for the following situations Browser compatibility Atto ExpressNAV Browser-based InterfaceNavigating ExpressNAV Reset button Parameter name Submit buttonExpressNAV Pages Tape Volumes ConfigurationLogical Units PartitionsReady CLI Interface via ASCII-based CommandsSaveConfiguration command Return type/mode Return format/content HostnameSummary of CLI Commands Command Defaults ExampleCLI index Zoneaddhost zone1 General Use Commands Ethernet Commands SNMPUpdates TelnetPasswordTelnetTimeout SNMPTrapsFibre Channel Configuration Commands FcPortList FcPortNameFcScsiBusyStatus FcWWNameSerial Port Configuration Commands SerialPortBaudRateSerialPortHandshake SerialPortEchoMaintenance Services Commands Diagnostic Commands PowerAudibleAlarm SledFaultLEDTapeVolumeInfo RAID5ClearDataStatusDrive Management Commands DriveWipe LUNStateIdeTransferRate IdeWriteCacheRAID5ClearData RAIDInterleaveRAIDHaltRebuild RAIDManualRebuildRestoreModePages TapeVolumeBlockSizeRebuildPriority TapeWriteProtectZoneClearAll ZoneCreateZoneDelete ZoneRemoveDeviceCLI configure drives Configuring the Diamond-VT Virtual Tape VolumesRAID Level Hot Spare sledsInterleave Enhancing performanceVirtual Tape To set up RAID Level 10 with Hot Spare sleds Optional Hot Spare SledPlanned configuration is a work-in-process ZonesPrinciples of Zoning Device portion defines the LUNsType ZoneInfo Factors to considerStatus and Sense Data Configuring Zoning To create a zoneTo remove zones To change current zonesErrors Zone definition tables The Zone commandsUpdating firmware via the optional Ethernet card Updating FirmwareUpdating firmware via the RS-232 serial port Cd c\diamond\flash Type put ....imaDiagnostics, Upgrade and Maintenance Power On Self Test Post Each timeRS-232 Monitoring Port and CLI One tool to Ethernet Monitoring Port and CLI If the optional25C 32C 35C 40C Power Supply Monitoring The Diamond-VTSystem Fault LED and Error Codes If a serious Disk Drive Activity and Disk Fault LEDs Each Monitoring, reporting Troubleshooting Windows 2000 special instructions Error MessagesCommand Line Interface messages Specific situations and suggestionsIf a power supply fails If you can’t access the Diamond-VT CLI via EthernetIf you cannot read or write to the Diamond-VT Type FirmwareRestart in CLIResetting Defaults Factory DefaultDefault Return to Default settingsCommand Default Rebuilding RAID Level 5 and 10 Configurations To synchronize mirrored drives manually Hardware Maintenance Hardware maintenance Hot Swap Operating Instructions Disk DrivesBlower Assemblies Power SuppliesTo replace a blower assembly Appendix a Glossary Fibre Channel technologySAN technology Scsi protocolAppendix Fibre Channel FeatureAppendix B ATA Disk Technology Appendix C LunInfo for a Jbod setup LunInfo PartitionInfo active 59TapeVolumeInfo ZoneInfoViii Appendix D Sample Zoning Command Sequences First time configuration after downloadSimple configuration Symmetric ModelAsymmetric Model ZoneClearAll ZoneCreate zone1ZoneAddPort zone1 ZoneCreate zone2 ZoneAddPort zone2 ZoneCreate zone3Combined Symmetric/Asymmetric Model Appendix E Specifications Rack Mount DimensionsFloor Mount Dimensions Environmental and physicalAppendix F Product Safety Safety compliancesEMC specifications Radio and television interferenceAppendix G Part numbers Description All modelsContact Atto Technology, Inc Appendix H WarrantyManufacturer limited warranty
Top Page Image Contents