ATTO Technology VT-Class manual Physical setup

Page 21
Stand-by
On
Power Switch Positions
3 Make sure the power switches on the power supplies on the rear of the unit are in the stand- by position. Plug in the power cords to the back of the unit, then into an appropriate power source (100-240 VAC). The power source must
be connected to a protective earth ground and comply with local electrical codes. Improper grounding may result in an electrical shock or damage to the
1 Insert the proper connector into the Host Interface Card in the back of the Diamond-VT. (See Connecting a Fibre Channel Array on page 11 or Connecting a SCSI Array on page 13).
2 Connect the cable (Fibre Channel or SCSI) from your host system to the Host Interface Card connector on the back of the Diamond- VT. The cable you use depends upon your application, the environment and distance.
unit.
Exhibit 3.2-1 Back side of a rack mount, Fibre Channel Diamond-VT with blower assemblies on top, power supplies at the bottom, separated by the Host Interface Card.
5 Reboot your computer
6 Determine the best configuration for your needs and refer to the rest of this manual for more detailed explanations and configuration information.
When the power is turned on, the LEDs on the front of the Diamond-VT flashes twice. Drives spin up in groups of three, about every one to two seconds. The individual LEDs blink. After all available drives have spun up, the individual drive LEDs stays lit. When all available drives are operational, the ready LED on the top front panel of the management card remains lit.
4 Press the stand-by power switch for each power supply to the ON position. When the green power LED on the back of the unit is lit, the power supply is fully operational and delivering power to the system. The power LED on the front of the array lights once the firmware begins to execute.
General Instructions

10 Physical setup

Image 21
Contents Diamond Storage Array VT-Class Page Page Contents ExpressNAV Pages Atto ExpressNAV Browser-based InterfaceSerial Port Configuration Commands Fibre Channel Configuration CommandsMaintenance Services Commands Diagnostic CommandsECC Drive Management CommandsDiagnostics, Upgrade and Maintenance Troubleshooting Configuring the Diamond-VTResetting Defaults Virtual TapeAppendix E Specifications Xii Appendix D Sample Zoning Command SequencesAppendix F Product Safety Xiii Appendix G Part numbers Xiv Appendix H WarrantyPreface DisclaimerAtto Technology, Inc Page Diamond Storage Array-VT Product Overview Diamond-VT featuresScsi model Fibre Channel modelRS-232 Diamond-VT Technical OverviewEthernet 400MB/secATA Interface Engine AIE The interface to each Adxt Powers ATA to New LevelsPhysical setup Installation InstructionsSet up the Ethernet connection Connect to EthernetConfiguration examples Set up Virtual Tape configurationConnect to Ethernet, on page 5, follow RAID Level 10 with Hot Spare sledsFloor model Diamond-VT ComponentsRack mount model Diamond-VT Physical Setup Floor ModelRack Mount Physical setup Connecting a Fibre Channel Array AutoconfigurationManual configuration Fibre Channel connections To connect the Scsi Diamond-VT Connecting a Scsi ArrayBus speed, MB/sec Bus width Max. bus lengths Max. device BitsScsi connections Command Line Interface Accessing the Diamond-VTAtto ExpressNAV RS-232 portSnmp In-band CLI Over Fibre Channel DetailsInitiator Host Diamond-VT Initiator/Host Diamond-VT Serial Port Access Serial port access To connect to the Ethernet port Ethernet Access Telnet and Snmp ProtocolsTo use Telnet To use SnmpTraps are generated for the following situations Atto ExpressNAV Browser-based Interface Navigating ExpressNAVBrowser compatibility Parameter name Submit button Reset buttonExpressNAV Pages Configuration Tape VolumesLogical Units PartitionsCLI Interface via ASCII-based Commands SaveConfiguration commandReady Hostname Return type/mode Return format/contentCommand Defaults Example Summary of CLI CommandsCLI index Zoneaddhost zone1 General Use Commands Ethernet Commands TelnetPassword SNMPUpdatesTelnetTimeout SNMPTrapsFibre Channel Configuration Commands FcPortName FcPortListFcScsiBusyStatus FcWWNameSerialPortBaudRate Serial Port Configuration CommandsSerialPortHandshake SerialPortEchoMaintenance Services Commands Diagnostic Commands SledFaultLED PowerAudibleAlarmTapeVolumeInfo RAID5ClearDataStatusDrive Management Commands LUNState DriveWipeIdeTransferRate IdeWriteCacheRAIDInterleave RAID5ClearDataRAIDHaltRebuild RAIDManualRebuildTapeVolumeBlockSize RestoreModePagesRebuildPriority TapeWriteProtectZoneCreate ZoneClearAllZoneDelete ZoneRemoveDeviceCLI configure drives Virtual Tape Volumes Configuring the Diamond-VTRAID Level Hot Spare sledsEnhancing performance InterleaveVirtual Tape Optional Hot Spare Sled To set up RAID Level 10 with Hot Spare sledsZones Planned configuration is a work-in-processPrinciples of Zoning Device portion defines the LUNsFactors to consider Status and Sense DataType ZoneInfo To create a zone Configuring ZoningTo remove zones To change current zonesZone definition tables The Zone commands ErrorsUpdating Firmware Updating firmware via the RS-232 serial portUpdating firmware via the optional Ethernet card Type put ....ima Cd c\diamond\flashPower On Self Test Post Each time Diagnostics, Upgrade and MaintenanceRS-232 Monitoring Port and CLI One tool to Ethernet Monitoring Port and CLI If the optionalPower Supply Monitoring The Diamond-VT System Fault LED and Error Codes If a serious25C 32C 35C 40C Disk Drive Activity and Disk Fault LEDs Each Monitoring, reporting Windows 2000 special instructions Error Messages TroubleshootingCommand Line Interface messages Specific situations and suggestionsIf you can’t access the Diamond-VT CLI via Ethernet If a power supply failsIf you cannot read or write to the Diamond-VT Type FirmwareRestart in CLIFactory Default Resetting DefaultsDefault Return to Default settingsCommand Default Rebuilding RAID Level 5 and 10 Configurations To synchronize mirrored drives manually Hardware Maintenance Hardware maintenance Disk Drives Hot Swap Operating InstructionsPower Supplies To replace a blower assemblyBlower Assemblies Fibre Channel technology Appendix a GlossarySAN technology Scsi protocolAppendix Feature Appendix B ATA Disk TechnologyFibre Channel Appendix C LunInfo for a Jbod setup PartitionInfo active 59 LunInfoZoneInfo TapeVolumeInfoViii First time configuration after download Appendix D Sample Zoning Command SequencesSimple configuration Symmetric ModelZoneClearAll ZoneCreate zone1 Asymmetric ModelZoneAddPort zone1 ZoneCreate zone2 ZoneAddPort zone2 ZoneCreate zone3Combined Symmetric/Asymmetric Model Rack Mount Dimensions Appendix E SpecificationsFloor Mount Dimensions Environmental and physicalSafety compliances Appendix F Product SafetyEMC specifications Radio and television interferenceDescription All models Appendix G Part numbersAppendix H Warranty Manufacturer limited warrantyContact Atto Technology, Inc