ATTO Technology VT-Class manual Drive Management Commands, Ecc

Page 7

Temperature

VirtualDriveInfo

ZoneInfo

ZoneState

6.8 Drive Management Commands

ATADiskState

AutoRebuild

ClearDiskReservedAreaData

DriveCopy

DriveCopyHalt

DriveCopyResume

DriveCopyStatus

DriveInfo

DriveSledPower

DriveWipe

ECC

IdeTransferRate

IdeWriteCache

InquiryData

LUNInfo

LUNState

MediumType

PartitionInfo

QuickTape

RAID5ClearData

RAID5ClearDataStatus

RAIDInterleave

RAIDHaltRebuild

RAIDManualRebuild

RAIDRebuildState

RAIDRebuildStatus

RAIDResumeRebuild

RebuildPriority

ResolveLUNConflicts

RestoreModePages

SledFaultLED

TapeDriveInfo

TapeVolumeBlockSize

TapeVolumeInfo

TapeWriteProtect

VirtualDriveInfo

ZoneAddDevice

ZoneAddHost

ZoneAddPort

ZoneClearAll

ZoneCommit

ZoneCreate

ZoneDelete

ZoneInfo

ZoneRemoveDevice

ZoneRemoveHost

ZoneRemovePort

ZoneRetrieve

ZoneState

Diamond Storage Array Installation and Operation Manual

Image 7

Contents Diamond Storage Array VT-Class Page Page Contents ExpressNAV Pages Atto ExpressNAV Browser-based InterfaceDiagnostic Commands Fibre Channel Configuration CommandsSerial Port Configuration Commands Maintenance Services CommandsECC Drive Management CommandsVirtual Tape Configuring the Diamond-VTDiagnostics, Upgrade and Maintenance Troubleshooting Resetting DefaultsAppendix G Part numbers Xiv Appendix H Warranty Appendix D Sample Zoning Command SequencesAppendix E Specifications Xii Appendix F Product Safety XiiiDisclaimer PrefaceAtto Technology, Inc Page Diamond Storage Array-VT Product Overview Diamond-VT featuresScsi model Fibre Channel model400MB/sec Diamond-VT Technical OverviewRS-232 EthernetATA Interface Engine AIE The interface to each Adxt Powers ATA to New LevelsConnect to Ethernet Installation InstructionsPhysical setup Set up the Ethernet connectionRAID Level 10 with Hot Spare sleds Set up Virtual Tape configurationConfiguration examples Connect to Ethernet, on page 5, followFloor model Diamond-VT ComponentsRack mount model Floor Model Diamond-VT Physical SetupRack Mount Physical setup Autoconfiguration Connecting a Fibre Channel ArrayManual configuration Fibre Channel connections Bits Connecting a Scsi ArrayTo connect the Scsi Diamond-VT Bus speed, MB/sec Bus width Max. bus lengths Max. deviceScsi connections RS-232 port Accessing the Diamond-VTCommand Line Interface Atto ExpressNAVSnmp Details In-band CLI Over Fibre ChannelInitiator Host Diamond-VT Initiator/Host Diamond-VT Serial Port Access Serial port access To use Snmp Ethernet Access Telnet and Snmp ProtocolsTo connect to the Ethernet port To use TelnetTraps are generated for the following situations Navigating ExpressNAV Atto ExpressNAV Browser-based InterfaceBrowser compatibility Parameter name Submit button Reset buttonExpressNAV Pages Partitions Tape VolumesConfiguration Logical UnitsSaveConfiguration command CLI Interface via ASCII-based CommandsReady Hostname Return type/mode Return format/contentCommand Defaults Example Summary of CLI CommandsCLI index Zoneaddhost zone1 General Use Commands Ethernet Commands SNMPTraps SNMPUpdatesTelnetPassword TelnetTimeoutFibre Channel Configuration Commands FcWWName FcPortListFcPortName FcScsiBusyStatusSerialPortEcho Serial Port Configuration CommandsSerialPortBaudRate SerialPortHandshakeMaintenance Services Commands Diagnostic Commands RAID5ClearDataStatus PowerAudibleAlarmSledFaultLED TapeVolumeInfoDrive Management Commands IdeWriteCache DriveWipeLUNState IdeTransferRateRAIDManualRebuild RAID5ClearDataRAIDInterleave RAIDHaltRebuildTapeWriteProtect RestoreModePagesTapeVolumeBlockSize RebuildPriorityZoneRemoveDevice ZoneClearAllZoneCreate ZoneDeleteCLI configure drives Hot Spare sleds Configuring the Diamond-VTVirtual Tape Volumes RAID LevelEnhancing performance InterleaveVirtual Tape Optional Hot Spare Sled To set up RAID Level 10 with Hot Spare sledsDevice portion defines the LUNs Planned configuration is a work-in-processZones Principles of ZoningStatus and Sense Data Factors to considerType ZoneInfo To change current zones Configuring ZoningTo create a zone To remove zonesZone definition tables The Zone commands ErrorsUpdating firmware via the RS-232 serial port Updating FirmwareUpdating firmware via the optional Ethernet card Type put ....ima Cd c\diamond\flashEthernet Monitoring Port and CLI If the optional Diagnostics, Upgrade and MaintenancePower On Self Test Post Each time RS-232 Monitoring Port and CLI One tool toSystem Fault LED and Error Codes If a serious Power Supply Monitoring The Diamond-VT25C 32C 35C 40C Disk Drive Activity and Disk Fault LEDs Each Monitoring, reporting Specific situations and suggestions TroubleshootingWindows 2000 special instructions Error Messages Command Line Interface messagesType FirmwareRestart in CLI If a power supply failsIf you can’t access the Diamond-VT CLI via Ethernet If you cannot read or write to the Diamond-VTReturn to Default settings Resetting DefaultsFactory Default DefaultCommand Default Rebuilding RAID Level 5 and 10 Configurations To synchronize mirrored drives manually Hardware Maintenance Hardware maintenance Disk Drives Hot Swap Operating InstructionsTo replace a blower assembly Power SuppliesBlower Assemblies Scsi protocol Appendix a GlossaryFibre Channel technology SAN technologyAppendix Appendix B ATA Disk Technology FeatureFibre Channel Appendix C LunInfo for a Jbod setup PartitionInfo active 59 LunInfoZoneInfo TapeVolumeInfoViii Symmetric Model Appendix D Sample Zoning Command SequencesFirst time configuration after download Simple configurationZoneAddPort zone2 ZoneCreate zone3 Asymmetric ModelZoneClearAll ZoneCreate zone1 ZoneAddPort zone1 ZoneCreate zone2Combined Symmetric/Asymmetric Model Environmental and physical Appendix E SpecificationsRack Mount Dimensions Floor Mount DimensionsRadio and television interference Appendix F Product SafetySafety compliances EMC specificationsDescription All models Appendix G Part numbersManufacturer limited warranty Appendix H WarrantyContact Atto Technology, Inc