Schneider Electric VW3A3310d user manual Entering IP addresses in the terminal, Configuring Bootp

Page 18

8. Configuration

b Entering IP addresses in the terminal

In the [1.9 - COMMUNICATION] (COM-)menu, [ETHERNET] (EtH-)submenu, enter the following IP addresses:

-[IP card] (IPC1) (IPC2) (IPC3) (IPC4).

-[IP Mask] (IPM1) (IPM2) (IPM3) (IPM4).

-[IP Gate] (IPG1) (IPG2) (IPG3) (IPG4) (not always required).

Note: Some controllers, such as Prosoft® and DeltaV® modules, require a Modbus address to be set in addition to the IP address. This address must be set in menu 1.9 of the drive, as well as in the software for the master device.

Turn the drive off and then back on again (control voltage if a separate power supply is being used), otherwise the IP addresses are not taken into account.

Note: Before entry begins, the IP address displayed is the active IP address.

If this address is modified, the new IP address entered is displayed. This IP address will be effective the next time the drive is turned on.

b Configuring BOOTP

The BOOTP service is used to assign IP addresses from the MAC address. The MAC address consisting of 6 octets (00-80-F4-80-xx-yy) must be entered in the BOOTP server. The MAC address appears on the label attached to the Ethernet card.

In the [1.9 - COMMUNICATION] (COM-)menu, [ETHERNET] (EtH-)submenu:

•Leave the IP address [IP card] (IPC1) (IPC2) (IPC3) (IPC4) at the value [0.0.0.0] (0) (0) (0) (0).

•Do not enable the FDR service: [FDR validation] (FdrU) = [No] (nO).

b Configuring FDR

The FDR service (based on DHCP) is used to assign the IP addresses and other parameters from the device name that must be entered in the drive and in the FDR server (DHCP).

In the [1.9 - COMMUNICATION] (COM-)menu, [ETHERNET] (EtH-)submenu:

•Leave the IP address [IP card] (IPC1) (IPC2) (IPC3) (IPC4) at the value [0.0.0.0] (0) (0) (0) (0).

•Enable the FDR service: [FDR validation] (FdrU) = [Yes] (YES).

For the FDR function, select the drive configuration as either:

•Local: [FDR Local Config.] (LCFG) = [Yes] (YES).

•Downloaded. In this case, it is essential to consult the “FDR Service” section.

Enter the device name, [DEVICE NAME], in the [7. DISPLAY CONFIG.] menu, [7.1 USER PARAMETERS] submenu. This menu is only accessible in expert mode: In the [2 ACCESS LEVEL] (LAC-)menu, set the level to [expert] (EPr).

Turn the drive off and then back on again (control voltage if a separate power supply is being used), otherwise the device name is not taken into account.

Note: The FDR function cannot be fully configured using the integrated display terminal as it does not provide access to the device name.

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Altivar 61 Page Table of contents Table of contents Important Information Please NoteBefore you begin Hazard of Electric SHOCK, EXPLOSION, or ARC FlashProgramming Manual Installation ManualDocumentation structure ATV61Introduction PresentationNotation Receipt Hardware setupInstalling the card in the drive Hardware descriptionPin Signal Connecting to the Ethernet networkCard RJ45 connector pinout Example of connection to an Ethernet networkEthernet network connection elements Ethernet menu Access to Ethernet menu via graphic display terminalAccess to Ethernet menu via the integrated display terminal ENTEthernet menu parameters IPP4 Code Description IPPIPP1 0.0.0 0 0 0 IPP2 IPP3 IPFFdrt FdrAFdrS FdrEConfiguration List of functions to be configuredAssigning IP addresses Configuring IP addressesPower-up Initialization Static Addressing DynamicEntering IP addresses in the terminal Configuring BootpConfiguring FDR IP card IPC1 IPC2 IPC3 IPC4 IP Mask IPM1 IPM2 IPM3 IPM4Configuring IO Scanning Reserving controlControl via Ethernet or the terminals in I/O profile Configuring the controlControl via Ethernet in I/O profile Parameter Value CommentControl via Ethernet in CiA402 Drivecom profile Control via Ethernet or the terminals in CiA402 profileProfile Separate Network management Configuring communication interruption managementCommunication monitoring CommunicationDrive response COM. Fault ManagementExternal Fault RDY NETConfiguring monitored parameters Format Range Terminal displayDiagnostics Signalling LEDsColor/ state Description Integrated display Available informationMonitoring the control Terminal Workshop Web serverExtended communication interruption Troubleshooting communication interruptionsEthernet communication interruption type CodeTroubleshooting the card Client Service Number of connections Software setupList of services supported TCP connectionsModbus TCP frames Unit ID Modbus TCP server Accessible parametersModbus TCP server Drive Modbus serversIPC1.IPC2.IPC3.IPC4 Address Size Description Access Possible values, commentsEthernet card parameters IPM1.IPM2.IPM3.IPM4IPP1.IPP2.IPP3.IPP4 IPF1.IPF2.IPF3.IPF4FDR autosave Code Modbus name Description Size of data Decimal List of Modbus functions supportedRead Holding Registers 3 function Byte MeaningWrite Single Register 6 function Write Multiple Registers 16 = 16#10 function Read/Write Multiple Registers 23 = 16#17 function 16#17Read Device Identification 43 = 16#2B function Bytes Meaning With the VW3A3310d Ethernet cardIO Scanning service Periodic variablesAddress Description Default value Address tableFDR service Local configuration First use Downloaded configurationDrive parameters configuration IP assignment Save DownloadingDownload the IP addresses Save the drive configuration parameters in the FDR serverReplacing a drive Check that the system is operationalPeriodic saving Other commandsConfiguration file LimitationsStandard web server Home menu Monitoring menu Diagnostics menuSetup menu Security submenu Documentation menu Web server functionsApplets Access to the web server Username and passwordWeb server user interface Home menuMonitoring menu Altivar Viewer Data Viewer Altivar Chart Diagnostics menuSetup menu Ethernet StatisticsHttp password and Data write password pages FDR Agent Lcfg = No nOError Code Local ConfigFile Error Restore CounterIO Scanner Enabling IO Scanning Assigning the IO Scanning periodic variablesTime out MasterMail Important NoticeDocumentation menu Access FTP serverFTP functionality Comment FunctionsFile system DIRFile management Downloading from the web serverPrinciple File name 32 characters maxWeb server Type File name Standard web server resourcesType File name Size Complete URL Bytes Complete URL BytesSnmp agent PresentationTree structure Objects Description Access Default value Objects handledATV Setup using PL7 Defining the hardware configurationBootp configuration Configuring Modbus messaging ModbusMulti Configuring periodic variables PLC Configuring the Dhcp address server FDR Setup using Concept Setup using ProWORX NxT Hardware configuration Traffic Cop Network configurationTCP/IP configuration O Scanner configuration Page 30072-452-37 2008-02
Top Page Image Contents